Kärcher CB 5/23 Originalbetriebsanleitung Seite 46

Display Fault
210 Wheel washing not facing outward
211 Wheel washing 1 is not facing outward
(traffic light forward + backward are blink-
ing once)
212 Wheel washing 2 is not facing outward
(traffic light forward + backward are blink-
ing twice)
220 Door 1 is not closed
221 Door 1 is not opened
222 Door 2 is not closed
223 Door 2 is not opened
224 Door 3 is not closed
225 Door 3 is not opened
226 Fault door 1, light barrier 1
227 Fault door 1, light barrier 2
228 Fault door 2, light barrier 2
229 Fault door 2, light barrier 1
230 Fault door 3, light barrier 2
231 Fault door 3, light barrier 1
233 Light barrier wheel wash blocked at the
start of the wash
236 Malfunction light barrier dryer 1 front
237 Malfunction light barrier dryer 1 centre
238 Malfunction light barrier dryer 1 rear
247 Error upon writing/reading the USB flash
drive
248 Error upon writing/reading the data mem-
ory of the control
249 Malfunction on machine 2 (cycle opera-
tion)
250 Unit has not been initialised
251 Emergency operations of processed water
are active
255 Error data record/wash counter
300 CAN bus error module A11 no connection
(in the main cabinet CB 5)
301 Excess current outlets CAN bus module
A11 (in the main cabinet CB 5)
302 Proximity switches "Side brush 3 inside"
and "Side-brush 3 outside" engaged at the
same time
303 Proximity switches "Side brush 4 inside"
and "Side-brush 4 outside" engaged at the
same time
306 Alignment side brush 3 too high
307 Alignment side brush 4 too high
308 Alignment side brush 3 too low
309 Alignment side brush 4 too low
310 Performance side brush 3 too low during
wash
311 Performance side brush 4 too low during
wash
314 Side brush 3 limit 4 exceeded for too long Cable, motor or transmission for the ro-
315 Side brush 4 limit 4 exceeded for too long
46
Possible cause
Unit not in normal setting or com-
pressed air supply has been switched
off
Drive-in door did not reach end position Check door
Drive-out door did not reach end posi-
tion
(with CB cycle: middle door/separating
door)
Drive-out door did not reach end posi-
tion
Light barrier is contaminated, blocked
or defective
Measurement drive has not yet been
done
Processed water unit has a fault
Loose connecting chord of the plates,
plates defective
Short circuit, water leakage
Limit switch is defective
Cable, motor or transmission for rota-
tion of the side brush defective
Motor circuit breaker in the main control
cabinet has tripped.
Cable, motor or transmission for rota-
tion of the side brush defective
tation of the side brush defective, or the
type of vehicle is not washable
21
-
EN
Remedy
Check compressed air supply; drive unit
into normal setting
Clean light barrier.
Turn off the equipment, wait, turn on the
equipment.
Repeat process, rewrite the USB flash
drive, use different USB flash drive
Switch off and switch on the unit, repeat
washing process, call Customer Service
Rectify malfunction on machine 2.
Washing is not possible; call Customer
Service
Repair processed water plant; unit an be
used with fresh water in emergency opera-
tions mode
* Emergency operation not possible with
CB 2 and CB 5.
Switch off and switch on the unit, repeat
washing process, call Customer Service
Switch off and switch on the unit, repeat
washing process, call Customer Service
Check limit switch for damages, switch on/
off the unit, repeat washing process
Switch off and switch on the unit, repeat
washing process, call Customer Service
Check the motor circuit breaker in the main
control cabinet.
Switch off and switch on the unit, repeat
washing process, call Customer Service
Drive vehicle out of the plant, switch off
main switch, wait for 10 seconds, switch on
main switch again, press Reset button,
press button Normal setting, repeat wash-
ing procedure.