Kärcher CB 5/23 Originalbetriebsanleitung Seite 42

Display Fault
100 Wheel wash 1 does not drive back to base
setting
101 Wheel wash 2 does not drive back to base
setting
102 Roof brush limit 4 too long exceeded
103 Side brush 1 limit 4 too long exceeded
104 Side brush 2 limit 4 too long exceeded
105 Washing section takes too long
106 Maximum idling time of portal exceeded
107 Frequency converter of lifting motors,
switched off due to excess current in lift/
lower roof-brush
108 Frequency converter lifting motors, shut-
down via excess current raise / lower roof
drier 1
109 Under-voltage has occurred
110 Flow switch of brush washing has been
triggered
112 Fault external high pressure
113 Fault external undercarriage wash
114 Motor circuit breaker for winch by Christ
underbody wash has tripped
115 Motor circuit breaker of pump Christ un-
derbody wash has tripped
116 Limit switch FA by Christ underbody wash
not left / not reached
117 Limit switch FE by Christ underbody wash
not left / not reached
118 Limit switches FA / FE by Christ under-
body wash engaged simultaneously
121 Limit switch roof drier 1, swivelling blade
does not transmit signal
122 Switching handle roof drier 1 engaged
123 Short/ narrow hall side 1 front key has
been pressed
124 Short/ narrow hall side 1 rear key has
been pressed
125 Short/ narrow hall side 2 front key has
been pressed
126 Short/ narrow hall side 2 rear key has
been pressed
127 Vehicle to broad on side 1 key has been
pressed
128 Vehicle to broad on side 2 key has been
pressed
131 Object holds back the side brush during
start-up
133 Water cabinet door opened
134 Proximity switches start driving and end
driving of the vehicle movement device
are engage simultaneously
135 Motor circuit breaker of the hydraulic
pump of the vehicle movement device has
tripped
42
Possible cause
No compressed air, wheel wash has
got jammed in the rim
Cable, motor or gear of rotation roof
brush defective or vehicle of this type
cannot be washed
Cable, motor or gear of rotation side-
brush 1 defective or vehicle of this type
cannot be washed
Cable, motor or gear of rotation side-
brush 2 defective or vehicle of this type
cannot be washed
Washing unit does not move during
washing
Lifting system of roof brush is difficult to
access
Lifting system roof dryer 1 sluggish
Fluctuations in mains voltage
no water during brush washing
Malfunction in the high-pressure sys-
tem
Malfunction in the underbody wash
Limit switch activated through foreign
metal or is defective
Compressed air supply faulty.
Mechanical swivel device drags, end
switch defective.
Check switching bracket and its limit
switch for damages
The switch has been pressed by a per-
son
Vehicle is too broad or has been posi-
tioned much to the left
Vehicle is too broad or has been posi-
tioned much to the right
Object in the washing plant
Limit switch activated through foreign
metal or is defective
17
-
EN
Remedy
Check compressed air supply and com-
pressor; switch off the unit and remove the
wheel wash from the rim; repeat washing
process
Drive vehicle out of the plant, switch off
main switch, wait for 10 seconds, switch on
main switch again, press Reset button,
press button Normal setting, repeat wash-
ing procedure.
Switch off and switch on the unit, repeat
washing process, call Customer Service
Check lifting system, switch off and switch
on the unit, repeat washing process, call
Customer Service
Check power supply, switch on/ off the
unit, repeat washing process
Check supply of fresh and processed wa-
ter, repeat washing process
Check high-pressure system
Check underbody wash
Reset motor protection switch; call Cus-
tomer Service if the problem recurs.
Check limit switch for damage, remove
loose metal parts
Check compressed air supply.
Repair mechanical device, replace end
switch.
Repeat washing process, call Customer
Service
Reset switch manually and press start key
on the wash card reader to continue with
washing
Reposition the vehicle, reset the switch
manually, continue with washing by press-
ing the start key at the wash card reader or
repeat washing process
Remove object
Close water cabinet door
Check limit switch for damage, remove
loose metal parts
Reset motor protection switch; call Cus-
tomer Service if the problem recurs.