User Parameters - Omron VARISPEED E7 IP54 Kurzanleitung

User Parameters

Param-
Name
eter No.
Initialize Data
Language
selection for
Digital Opera-
A1-00
tor display
(JVOP-160-
OY only)
Parameter
A1-01
access level
A1-03 Initialize
Sequence / Reference Source
Reference
b1-01 source selec-
tion
RUN com-
b1-02 mand source
selection
Stopping
b1-03 method selec-
tion
Prohibition of
b1-04 reverse opera-
tion
Speed Search
Speed search
selection (cur-
b3-01 rent detection
or speed cal-
culation)
EN-19
Description
0:English
2:German
3:French
4:Italian
5:Spanish
6:Portuguese
0:Monitoring only (Monitoring drive
mode and setting A1-01 and A1-
04.)
1:Used to select user parameters
(Only parameters set in A2-01 to
A2-32 can be read and set.)
2:Advanced
(Parameters can be read and set in
both, quick programming mode (Q)
and advanced programming mode
(A).)
0: No initializing
1110:Initializes using the user
parameters
2220:Initializes using a two-wire
sequence. (Initializes to the factory
setting.)
3330: Initializes using a three-wire
sequence.
Sets the frequency reference input
method.
0:Digital Operator
1:Control circuit terminal (analog
input)
2:Serial communication (RS422 /
485)
3:Option Card
Sets the run command input method.
0:Digital Operator
1:Control circuit terminal (digital
inputs)
2:Serial communication (RS422 /
485)
3:Option Card
Selects the stopping method when
the Run signal is removed
0:Deceleration to stop
1:Coast to stop
2:DC injection to stop
3:Coast to stop with timer (New Run
commands are disregarded while
coasting.)
0:Reverse enabled
1:Reverse disabled
2:Output Phase Rotation (both rota-
tional directions are enabled)
3:Output Phase Rotation with
Reverse disabled.
Enables/disables the speed search
function and sets the speed search
method.
0:Disabled, speed calculation
1:Enabled, speed calculation
2:Disabled, current detection
3:Enabled, current detection
Param-
Name
eter No.
Disables or enables the bi-directional
Bi-directional
capabilities of the speed search func-
b3-14 speed search
tion.
selection
0:Disabled
1:Enabled
PI Control
0:Disabled
PI control
1:Enabled
b5-01 mode selec-
3:PI control enabled (frequency refer-
tion
ence+ PI output)
Sets the proportional gain of the PI
Proportional
b5-02 controller. P control is not performed
(P) gain
when set 0.00.
Sets the integral time of the PI con-
Integral (I)
b5-03 troller. I control is not performed when
time
set to 0.0 sec.
Selects forward/reverse direction for
PI output
PI output.
b5-09 characteris-
0:PI output is forward
tics selection
1:PI output is reverse.
Accel/decel
Sets the accel/decel time for the PI
b5-17 time for PI ref-
Softstarter (SFS).
erence
PI Setpoint
0:Disabled
b5-18
Selection 1:Enabled
b5-19 PI Setpoint PI target value
PI Unit Selects the units for the PI controller
b5-31
Selection values (b5-19, U1-24, U1-38).
Acceleration / Deceleration Settings
Acceleration/ Sets the time to accelerate/decelerate
C1-
Deceleration from 0 Hz to the maximum output fre-
times quency.
S-Curve Settings
S-curve char-
Sets the S-curve characteristic at
C2-
acteristic time
acceleration start and end.
at acceleration
Carrier Frequency
Selects the carrier frequency (factory
setting depends on Inverter capacity)
0: Low noise, low carrier
1: 2.0 kHz
Carrier fre-
2: 5.0 kHz
C6-02 quency selec-
3: 8.0 kHz
tion
4: 10.0 kHz
5: 12.5 kHz
6: 15.0 kHz
F: Programmable pattern
Speed Settings
Multi speed
d1-01
to references 1
d1-04
to 4
Sets the multi-step speed references.
Jog fre-
d1-17 quency refer-
ence
Reference Limits
Frequency ref- Sets the frequency reference upper
d2-01 erence upper limit in percent of the max. output fre-
limit quency (E1-04)
Frequency ref- Sets the frequency reference lower
d2-02 erence lower limit in percent of the max. output fre-
limit quency (E1-04)
Description