Electrical Connection; Gas Connection; Function Check; Warning Information - Truma Trumatic E 4000 Gebrauchsanweisung

Electrical
connection
12 V/24 V
Electric cables, switching
units and control units for
heaters must be arranged in
the vehicle in such a way that
their satisfactory operation
cannot be adversely affected
under normal operating con-
ditions. All cables leading to
the outside must be splash
proof at the leadthrough
opening.
Prior to working on electric
components the appliance
must be disconnected from
the power supply. Switching
off at the control panel is not
sufficient!
When carrying out electric
welding work on the body
the appliance connection
must be disconnected from
the vehicle electrical system.
If the connections are
transposed there is a
risk of cable burning. This
also rules out any guarantee
or liability claims!
The red cable is posi-
tive, the blue cable is
negative!
Connect the appliance to the
fused vehicle electrical sys-
tem (central electrical sys-
tem 5 – 10 A) using the 2 x
2
1.5 mm cable, for lengths
2
over 6 m use 2 x 2.5 mm
cable. Negative cable to
central ground. For direct
connection to the battery the
positive and negative cable
must be fused. Connections
in Faston terminals, fully
insulated (motor vehicle flat
connector system, 6.3 mm).
Do not connect any other
consumers to the supply line!
When power supplies
are being used, it must
be noted that the output volt-
age is between 11 V and 15 V
and the alternating current
ripple is < 1.2 Vpp.
Fig. H4: The Truma battery
charger NT 12/ 3-18 (Part no.
39901-01) is recommended
for connecting multiple 12 V
devices. This charger (with
a charging current of 18 A)
is suitable for charging lead-
acid or lead-gel batteries.
Other chargers must only be
used with a 12 V battery as
a buffer. Mains power sup-
plies and other power supply
equipment must have a
controlled 12 V output
(AC component less than
1 Vpp).
16
For saving the battery
we recommend using
solar collectors. Please ask
for information from your
dealer.

Gas connection

The operating pressure
of the 30 mbar gas
supply must correspond with
the operating pressure of the
device (see data plate).
The 8 mm diameter gas sup-
ply pipe must be attached
to the connecting piece with
a cutting ring connection.
Carefully counterhold with
another spanner when
tightening!
The gas connecti on fitting
on the appliance is not to be
shortened or bent.
Prior to connecting the appli-
ance make sure that the gas
lines are free from dirt, chips
and such!
Route the pipes in such a
way that the appliance can be
removed again for servicing.
Keep the number of parting
connections in the gas sup-
ply line in rooms frequented
by people to a technically
feasible minimum.
The gas system must ac-
cord with the technical and
administrative provisions
of the individual country of
use (in Europe, for example,
EN 1949 for motor vehicles
or EN ISO 10239 for boats).
National regulations and rul-
ings (in Germany, for
example, the DVGW work-
sheet G 607 for motor
vehicles or G 608 for boats)
must be respected.

Function check

After installation, the gas
feed line must be tested
for tightness by the pres-
sure-drop method. A test
certificate (in Germany, for
example, in accordance with
DVGW Worksheet G 607 for
motor vehicles or G 608 for
boats) is to be issued.
All equipment functions must
be tested in accordance
with the user manual after
installation.
The operating instructions
and completed guarantee
card are to be given to the
owner of the vehicle.
Take the nameplate of
the operating instruc-
tions and installation instruc-
tions and adhere to a place
on the appliance which is
clearly visible and protected
against damage. The year
of initial operation must be
marked on the data plate.
Warning
information
The installer or vehicle owner
must apply the yellow sticker
with the warning informa-
tion, which is enclosed with
the appliance, to a place in
the vehicle where it is clearly
visible to all users (e.g. on
the wardrobe door)! Ask
Truma to send you stickers,
if necessary.