Herunterladen Inhalt Inhalt Diese Seite drucken

Declaration Of Conformity - EDELRID VERTIC TRIPLE LOCK II Bedienungsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
ten confirmation from an authorised body should be is-
sued before further use is allowed.
- if there are doubts concerning safe use;
- if sharp edges have the potential to damage the rope of
hurt the user;
- if visible signs of damage material (e.g. cracks, plastic
deformation);
- if the material shows deep corrosion;
- if the product was exposed to extreme temperatures;
- if the material has come in contact with chemicals;
- if the load bearing straps had contact with a sharp
edge;
- if the product has been subjected to a hard fall load or
high shock loads occurring in a pendulum fall.
Inspection and documentation
In case of commercial use, the product must be inspect-
ed regularly or at least once a year by the manufacturer,
a qualified person or an approved inspection body /
agency; thereafter it may have to be serviced or removed
from use. Legibility of the markings has to be checked.
Such inspections and service must be documented for
each product. The following information must be record-
ed: Product identification and name, manufacturer's
name and contact details, unique identification, date of
manufacture, date of purchase, date of initial use, date of
next regular inspection, result of inspection, and signa-
ture of qualified person responsible. A suitable specimen
is found at www.edelrid.de
In case of commercial use, the relevant information con-
tained in this user manual must be made available to
each user before using the product.
STORAGE, MAINTENANCE AND TRANSPORT
Storage
Store cool, dry, and protected from daylight outside
transport containers. Prevent contact with chemicals.
Maintenance (12.)
Clean contaminated products in hand warm water and
rinse properly. Dry at room temperature, never in dryers or
near heaters/ radiators! Commercial halogen-free disin-
fectants may be used if required. The joints of metal parts
must be cleansed regularly and then be lubricated with
acid-free oil or a lubricant based on Teflon or silicone.
Transport
The product must be kept away from chemicals, dirt and
mechanical damage. For this purpose, a protective bag or
special storage and transport containers should be used.
PRODUCT LABELLING (SEE 1., H)
Marking on the product (EN)
Manufacturer: EDELRID
Model: Vertic TripleLock II and Vertic TripleLock II Black
Figures: Opening and closing of the buckles
Product designation: Fall arrest harness to EN 361:2002,
Work positioning harness to EN 358:2018, Sit harness to
EN 813:2008 and Full body harness to ANSI Z359.11:
2014.
Lot number
0123: The identification of the notified body monitor-
ing the production of the PPE (TÜV SÜD Product Service
GmbH, Ridlerstrasse 65, 80339 München, Deutschland)
The warning message and instructions must be read
and observed
YYYY MM: Year and month of manufacture
EN 813: 2008: Max. user weight, incl. equipment in kg
Gear loops: 25 kg maximum load; Work sit loops: 75 kg
maximum each
Size range of hip belt
Size: 1, 2
A: attachment element to EN 361 (see 1. A)
Marking on the product (ANSI)
Product designation: Full Body Harness to ANSI
Z359.11-2014
Range of user weight: 130 – 310 lbs
Lanyard parking element: see 9

DECLARATION OF CONFORMITY

EDELRID GmbH & Co. KG herewith declares that this
article is in conformity with the essential requirements
and the relevant provisions of EU regulation 2016/425.
The original Declaration of Conformity can be download-
ed at the following site on the internet: http://www.
edelrid.de/...
Our products are made with greatest care. If you find any
justified cause for complaint, please indicate the lot
number of the product concerned.
Technical changes reserved.

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis