Moretti Forni R14E Bedienungsanweisung Seite 24

3.3 The equipment has further settings that are available
from the main menu. To access these functions, press the
"MENU" key then scroll
"SELECTION" keys until the required item. Press "OK" to open
the sub menu.
3.3.1 LIGHTING
Used to switch the lighting on and off inside the baking chamber.
Select this menu item to manage lighting manually. The lighting
status is represented graphically on the display by a check symbol on
the right of the menu item. This check symbol means that the lighting
is on.
3.3.2 HOTKEY
The "Hotkey" function ( "star" key) is a key that can be customised
for direct access to a specific function, as chosen by the user.
Enter the "Hotkey" menu to view the current setting represented by
the selected item. To assign a different function to a "Hotkey", move
the highlighting with the "SELECTION" keys to the required item
and press "OK" to confirm.
If necessary, press "RETURN" until you return to the main screen.
Press the "Hotkey" to directly enable the selected function.
3.3.3 SWITCH ON TIMER
This function can be used to order timed start-up of the oven, setting
up to two different start-up and shut-down times for every day of the
week (fig. 22a).
Scroll through the list on the display using the "SELECTION" keys
to select the following items.
- "Enable/Disable": enables/disables the on timer
"Settings": to manage the on/off times programmed
Scroll through the list with the "SELECTION" keys as far as the
"Enable" and press "OK" to confirm and enable the function. If there
is no on/off set time, you will be redirected to the "Settings" screen
to add at least an on/off set time.
Place the cursor with the "SELECTION" buttons on the time screen
relative to the day of the week to be programmed. The days of the
week are set out on 4 pages. The switch on times are graphically
represented by "ON" and the switch off times by "OFF". Times are
graphically represented as HH:MM. //:// show that switch on/off are
disabled.
Use the "+" and "-" keys to increase/reduce the selected field. In the
HH field, select the "//" symbol to disable a specific timer. At the end
of the setting process, press "OK" to confirm. Press "RETURN" to
go back to the previous screen without confirming the changes.
When the switch on timer is enabled, the top bar contains the "Timer
On" icon (fig 11 part. I), while when the oven is in STOP mode, the
status bar messages also include the next time time the oven will be
switched on, using the format "ON dd hh:mm". While the oven is
switching off, the status bar will read "OFF dd hh:mm".
The settings table needs to be completed with even just one "On" to
activate the function: the oven will switch on at the first "on"
chronologically enabled and which it encounters from the moment it
is enabled
NOTE:
Setting an "On" without setting a subsequent "Off"
will still be considered an active setting: the oven will turn on
automatically at the time set, and will have to be turned off
manually. In the same way, setting "Off" that does not involve a
prior "On" will also be considered an active setting and the oven
will switch off automatically at the set time, if it was manually
switched on beforehand.
At the switch on (or off) time, an intermittent buzzer will sound and
the status icon for the timer will indicate that the oven is about to turn
on (or off). Use the Start/Stop button to switch on (or off).
WARNING!
The sound alarm serves to signal that the
appliance is about to start up and therefore, anyone within its
radius of activity for any reason must move to a safe distance or
disconnect the equipment from the power supply; the above
function and relevant risk must be made known to all those who
might be in the vicinity of the appliance for the purpose of
safeguarding them against accidents or injury.
Once the oven starts up (or shuts down) again at the same time, the
"Timer" function will stay on. Therefore, if no changes are made,
one week later at the same time, the oven will start up (or shut down)
again.
through the list with the
NOTE:
If the operator forces an oven start-up when the
timer is switched on before the set time, then the oven will start
up normally and at the start-up time set for the timer, everything
will proceed as usual (the oven is already on and therefore no
buzzer will sound). The same thing happens if the oven is already
off at the time set for shut down.
NOTE:
If there is a power outage while the timer is being
used (Black-out) no parameters will be changed; the important
thing is for the power to return before the start up time.
NOTE:
The control unit is equipped with an internal timer,
after which the display turns off automatically if the oven is on
STOP mode. Press any button to activate the control unit. If the
main switch is on "1" and the display is off - make sure that the
control unit is not in this status before turning off the switch.
Press any key then proceed as described in point 3.4. to activate
the control unit.
3.3.4 SETTING THE TIME/DATE
To set the time and date, use the "SELECTION" keys to edit any
change. Use the "+" and "-" keys to increase/reduce the selected
field. Press "OK" to confirm the change. Press "RETURN" to go
back to the previous screen without confirming the changes.
The time format is given as HH: MM. The date format is given as
DD/MM/YY.
3.3.5 SETTING THE LANGUAGE:
To change the language settings, scroll through the list with the
"SELECTION" keys to find the required item and press "OK" to
confirm. Press "RETURN" to go back to the previous screen
without confirming the changes.
3.3.6 °C/°F SETTING
The oven can be set to use/view temperatures in centigrade (°C) or
Fahrenheit (°F). The current setting is displayed on the main screen
to the right of the temperature with the appropriate symbol.
To change the current settings, scroll through the list with the
"SELECTION" keys to find the required item and press "OK" to
confirm. Press "RETURN" to go back to the previous screen
without confirming the changes.
3.3.7 ASSISTANCE
This menu contains information about the oven which will be needed
when requesting Assistance.
Scroll through the list on the display using the "SELECTION" keys
to select the following items.
- "Info": displays information about Service, software version
installed and current oven configuration.
-"Update software": starts software update
WARNING!
authorised by the Manufacturer. The operation may compromise
the correct operation of the appliance.
- "Reset": It starts the partial reset of the Manufacturer's default
settings (any Programs present remain stored in memory)
WARNING!
authorised by the Manufacturer. The operation may compromise
the correct operation of the appliance.
- "Factory settings": starts the general default settings process (any
existing Programs are deleted)
WARNING!
authorised by the Manufacturer. The operation may compromise
the correct operation of the appliance.
-"Align": starts the vertical alignment process for the graphic. Use
the "SELECTION" keys to move the corresponding graphic.
-"Alarms": displays any errors. "SELECTION UP" key scrolls
through the list of alarms present. The appliance status, in case there
are pending alarms, is shown on the status bar with the corresponding
status icon (fig.24a pos.M)
"Logfile": starts diagnostic data saving procedure on external USB
device.
-"Advanced": displays the advanced settings of the configuration
page. See point 3.3.7.1.
"Format": starts the formatting process.
UK8
Procedure reserved to trained personnel
Procedure reserved to trained personnel
Procedure reserved to trained personnel