Scheppach HMS1070 Original Bedienungsanleitung Seite 30

5 Securely store unused power tools
- Unused power tools should be stored in a dry,
elevated or closed location out of the reach
of children.
6 Do not overload your power tool
- They work better and more safely in the spec-
ified output range.
7 Use the correct power tool
- Do not use low-output machines for heavy
work.
- Do not use the power tool for purposes for
which it is not intended.
- For example, do not use handheld circular
saws for the cutting of branches or logs.
8 Wear suitable clothing
- Do not wear wide clothing or jewellery, which
can become entangled in moving parts.
- When working outdoors, anti-slip footwear is
recommended.
- Tie long hair back in a hair net.
9 Use protective equipment
- Wear safety goggles.
- Wear a mask when carrying out dust-creat-
ing work.
10 Connect the dust extraction device
- If connections for dust extraction and a collect-
ing device are present, make sure that they
are connected and used properly.
11 Do not use the cable for purposes for which it is
not intended
- Do not use the cable to pull the plug out of the
socket. Protect the cable from heat, oil and
sharp edges.
12 Secure the workpiece
- Use the clamping devices or a bench
vice to hold the
In this manner, it is held more securely than
with your hand.
13 Avoid abnormal posture
- Make sure that you have secure footing and
always maintain your balance.
14 Take care of your tools
- Keep cutting tools sharp and clean in order to
be able to work better and more safely.
- Follow the instructions for lubrication and for
tool replacement.
- Check the connection cable of the electric tool
regularly and have it replaced by a recognised
specialist when damaged.
- Check extension cables regularly and replace
them when damaged.
- Keep the handle dry, clean and free of oil and
grease.
30 | GB
workpiece in place.
www.scheppach.com
15 Pull the connector out of the socket
- When the power tool is not in use or prior to
maintenance and when replacing tools such
as saw blades, drills, cutters.
- If the planing shaft jams while working due to
excessive feeding force or the workpiece jam-
ming, switch the device off and disconnect it
from the mains. Remove the workpiece and
make sure that the planing shaft runs freely.
Switch the device on and carry out the cutting
operation again with reduced feeding force.
16 Do not leave a tool key inserted
- Before switching on, make sure that keys and
adjusting tools are removed.
17 Avoid inadvertent starting
- Make sure that the switch is switched off when
plugging the plug into an outlet.
18 Use extension cables for outdoors
- Only use approved and appropriately identi-
fied extension cables for use outdoors.
19 Remain attentive
- Pay attention to what you are doing. Remain
sensible when working. Do not use the power
tool when you are distracted.
20 Check the power tool for potential damage
- Protective devices or other parts with minor
damage must be carefully inspected to ensure
that they function correctly and as intended
prior to continued use of the power tool.
- Check whether the moving parts function fault-
lessly and do not jam or whether parts are
damaged.
- All parts must be correctly mounted and all
conditions must be fulfilled to ensure fault-free
operation of the power tool.
- Damaged protective devices and parts must
be repaired properly or replaced by a recog-
nised specialist workshop unless otherwise
specified in the usage instructions.
- Damaged switches must be replaced at a cus-
tomer service workshop.
- Do not use any power tool on which the switch
cannot be switched on and off.
21 ATTENTION!
- The use of other insertion tools and other ac-
cessories can entail a danger of injury.
22 Have your power tool repaired by a qualified
electrician
- This power tool conforms to the applicable
safety regulations. Repairs may only be per-
formed by an electrician using original spare
parts. Otherwise accidents can occur.