Grundfos Control MPC-Serie Installationsanleitung Seite 404

‫ﻣ ﻥ ﺧ ﻼﻝ ﺍﻟﻘﺎﺋﻣ ﺔ، ﺑﺈﻣﻛﺎﻧ ﻙ ﺿ ﺑﻁ ﺍﻟﻭﻅ ﺎﺋﻑ ﺍﻟﻣﺗﻌﻠﻘ ﺔ ﺑﻭﺣ ﺩﺓ ﺍﻟﺗﺣﻛ ﻡ‬
‫ﺍﻷﺳﺎﺳ ﻳﺔ. ﻣ ﻥ ﺍﻟﻣﻬ ﻡ ﻓﻘ ﻁ ﻋﻣ ﻝ ﺇﻋ ﺩﺍﺩﺍﺕ ﻓ ﻲ ﻫ ﺫﻩ ﺍﻟﻘﺎﺋﻣ ﺔ ﺇﺫﺍ ﻛ ﺎﻥ ﺳ ﻳﺗﻡ ﺗﻣﺩﻳ ﺩ‬
:‫ﺍﻟﻌﻣ ﻝ ﺑﻬ ﺫﻩ ﺍﻟﻭﻅ ﺎﺋﻑ ﻣ ﻥ ﺧ ﻼﻝ ﺇﺣ ﺩﻯ ﺍﻟﻭﻅ ﺎﺋﻑ ﺃﺩﻧ ﺎﻩ‬
404
Primary controller (4.1) 8.7.1
8 . 7 . 1
Primary controller 36 ‫ﺷ ﻛﻝ‬
3 6 ‫ﻝ ﻙ ﺵ‬
‫ﺍﻟﻭﺻ ﻑ‬
PI controller •
•
Alternative setpoints •
•
External setpoint influence •
•
Primary sensor •
•
Secondary sensor •
•
Clock program •
•
Proportional pressure •
•
S-system configuration. •
•
:‫ﻓ ﻲ ﻗﺎﺋﻣ ﺔ "ﺍﻹﻋ ﺩﺍﺩﺍﺕ"، ﻳﻣﻛﻧ ﻙ ﺿ ﺑﻁ ﺍﻟﻭﻅ ﺎﺋﻑ ﺍﻟﺗﺎﻟﻳ ﺔ‬
Primary controllerPI controller, Alternative setpoints, External
setpoint influence, Primary sensor, Secondary sensor, Clock
program, Proportional pressure, S-system configuration,
Pump cascade controlMin. time between start/stop, Max.
number of starts/hour, Number of standby pumps, Forced pump
changeover, Pump test run, Pump stop attempt, Pump start
and stop speed, Min. performance, Compensation for pump
Secondary functionsStop function, Pilot pump, Soft pressure
build-up, Digital inputs, Analog inputs, Digital outputs*, Analog
outputs, Counter inputs, Emergency run, Min., max. and user-
defined duty, Pump curve data, Control source, Fixed inlet
pressure, Flow estimation, Reduced operation, Multisensor
Monitoring functionsDry-running protection, Min. pressure,
Max. pressure, External fault, Limit 1 exceeded, Limit 2
exceeded, Pumps outside duty range, Pressure relief, Log
values, Fault, primary sensor, Non-return valve.
Functions, CU 352Display language, Units, Date and time,
Password, Ethernet, GENIbus number Software status, Display
‫ﻳﻣﻛ ﻥ ﺗﺣﺩﻳ ﺩ ﻟﻐ ﺔ ﺍﻟﺧﺩﻣ ﺔ، ﺍﻹﻧﺟﻠﻳﺯﻳ ﺔ ﺍﻟﺑﺭﻳﻁﺎﻧﻳ ﺔ، ﻷﻏ ﺭﺍﺽ ﺍﻟﺧﺩﻣ ﺔ. ﻋ ﺎﺩﺓ‬
.‫ﻣ ﺎ ﻳﺗ ﻡ ﺿ ﺑﻁ ﻛ ﻝ ﻫ ﺫﻩ ﺍﻟﻭﻅ ﺎﺋﻑ ﺑﺷ ﻛﻝ ﺻ ﺣﻳﺢ ﻋﻧ ﺩ ﺑ ﺩء ﺗﺷ ﻐﻳﻝ ﺍﻟﻧﻅ ﺎﻡ‬
Settings (4) 8.7
8 . 7
Settings 35 ‫ﺷ ﻛﻝ‬
3 5 ‫ﻝ ﻙ ﺵ‬
•
Setpoint ramp.
•
•
start-up time.
•
•
settings.
•
•
•
•
1, Display 2, Display 3.
•
•
•