Grundfos Control MPC-Serie Installationsanleitung Seite 16

Continued from page 15
1 ->
16
4. Settings
4.1 Primary controller
4.1.1 PI controller
4.1.2 Alternative setpoints
4.1.2.1
4.1.3 External setpoint influence
4.1.3.1
4.1.4 Primary sensor
4.1.5 Secondary sensor
4.1.6 Clock program
4.1.7 Proportional pressure
4.1.8 S-system configuration
4.1.9 Setpoint ramp
4.2 Pump cascade control
Min. time between start/stop
4.2.1
Max. number of starts/hour
4.2.3 Standby pumps
4.2.4 Forced pump changeover
4.2.5 Pump test run
4.2.7 Pump stop attempt
4.2.8 Pump start and stop speed
4.2.9 Min. performance
4.2.10 Compensation for pump start-up time
4.3 Secondary functions
4.3.1 Stop function
4.3.1.1
4.3.2 Pilot pump
4.3.3 Soft pressure build-up
4.3.5 Emergency run
4.3.7 Digital inputs
4.3.8 Analog inputs
Setting, AI1 (CU 352), [51] - AI3, [51, 54, 57]
Setting, AI1 (IO 351-41), [57] - AI2 [57, 60]
Setting, AI1 (IO 351-42), [57] - AI2 [57, 60]
4.3.9 Digital outputs
DO1 (CU 352), [71] is signalling - DO2 [71, 74]
DO1 (IO 351-41), [77] is signalling - DO7 [77-88]
DO1 (IO 351-42), [77] is signalling - DO7 [77-88]
4.3.10 Analog outputs
AO1 (IO 351-41) [18] - AO3 [18, 22, 26]
AO1 (IO 351-42) [18] - AO3 [18, 22, 26]
4.3.11 Counter inputs
Volume counter, DI1 (IO 351-41), [10] - DI2[10, 12]
Volume counter, DI1 (IO 351-42), [10] - DI2[10, 12]
4.3.14 Min., max. and user-defined duty
4.3.14.1
4.3.14.2
4.3.14.3
4.3.18 Pilot pump curve data
4.3.19 Pump curve data
4.3.23
4.3.20 Control source
4.3.22 Fixed inlet pressure
4.3.23 Flow estimation
4.3.24 Reduced operation
4.3.25 Multisensor settings
4.4 Monitoring functions
4.4.1 Dry-running protection
4.4.1.1
4.4.1.2
4.4.1.3
4.4.2 Min. pressure
4.4.3 Max. pressure
4.4.4 External fault
4.4.5 Limit 1 exceeded
4.4.6 Limit 2 exceeded
4.4.7 Pumps outside duty range
4.4.8 Pressure relief
4.4.9 Log values
4.4.10 Fault, primary sensor
4.4.11 Non-return valve
4.5 Functions, CU 352
Change language to the service language (English)
Run wizard again
4.5.1 Display language
4.5.2 Units
4.5.2.1
4.5.2.2
4.5.2.3
4.5.2.4
4.5.2.5
4.5.2.6
4.5.2.7
4.6 Status display menu
Alternative setpoints 2-7
Input value to be influenced by
4.1.3.2 Setting of influence function
Stop parameters
Function, DI1 (CU 352) - DI3, [10, 12, 14]
Function, DI1 (IO 351-41) - DI9, [10-46]
Function, DI1 (IO 351-42) - DI9, [10-46]
Function, AI1 (CU 352) - AI3 [51, 54, 57]
Function, AI1 (IO 351-41) - AI2 [57, 60]
Function, AI1 (IO 351-42) - A2 [57, 60]
Min. duty
Max. duty
Set user-defined duty
Flow estimation
Pressure/level switch
Measurement, inlet pressure
Measurement, tank level
Pressure
Differential pressure
Head
Level 4.5.2.8 Temperature
Flow rate 4.5.2.9 Power
Volume 4.5.2.10 Energy
Specific energy
4.5.3 Date and time
4.5.4 Password
4.5.5 Ethernet
4.5.6 GENIbus number
4.5.9 Software status