Scheppach HP2500S Originalbetriebsanleitung Seite 37

• If possible, keep the packaging until the expiry of the
warranty period.
• Familiarise yourself with the product by means of the
operating instructions before using for the first time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Spare parts
can be obtained from your specialist dealer.
• When ordering please provide our article number as
well as type and year of manufacture for the product.
m WARNING!
The product and the packaging material are not
children's toys! Do not let children play with plas-
tic bags, films or small parts! There is a danger of
choking or suffocating!
8. Layout
You will need the following tool to assemble the plate com-
pactor HP2500S:(*not included in the scope of delivery)
• Allen screw AF6*
You will need the following tool to assemble the plate
compactor HP3000S:(*not included in the scope of de-
livery)
• Open-ended spanner AF17
8.1 Mounting the handle (1) (HP2500 S: Fig. 3 + 4)
(HP3000S: Fig. 3a + 4a)
1. Undo the fixing screws (1a).
2. Turn the handle (1) as shown and secure it with the
fixing screws (1a), washers (1b) and spring washers
(1c).
8.2 Fitting the drive mechanism (Fig. 5)
1. Tilt the plate compactor forward using the handle (1).
2. Align the drive unit in the hole provided and carefully
lower the plate compactor.
3. You can now transport the plate compactor.
Attention: Before compacting, always remove the
drive mechanism and store it in a place outside the
working area.
When changing the machine position, it can be
equipped with the enclosed wheel kit (see 9.2 Installing
the drive mechanism).
8.3 Fitting the rubber pad (HP 2500S: Fig. 6)
(HP3000S: Fig.6a)
When using the plate compactor on paving stones, fit the
rubber pad with fastening bar (20) to prevent chipping
and scratching of the stone surface.
Attention! Use the rubber pad only for bedding in con-
crete blocks, concrete slabs and similar.
Remove the rubber pad when compacting gravel, grit
and the like.
1. To mount the rubber pad with fastening bar (20),
place the machine with the base plate (10) on the
rubber pad with fastening bar (20).
2. Align the rubber pad with fastening bar (20) so that
the holes match the screw points on the device.
3a. HP2500S: Secure the rubber pad with fastening
bar (20) at the front using three M10 x 20 mm hex-
agon screws (21), three small washers (21b) at the
top, three large washers (21c) at the bottom and
three lock nuts (21a).
3b. HP3000S: Secure the rubber pad with fastening
bar (20) at the front using four M10 x 20 mm hex-
agon screws (21), four small washers (21b) at the
top, four large washers (21c) at the bottom and four
lock nuts (21a).
4. Tighten all the screws well.
9. Before commissioning
m Attention!
Always make sure the product is fully assembled
before commissioning!
m WARNING!
Health hazard!
Inhalation of petrol/lubricating oil vapours and exhaust
gases can cause serious damage to health, uncon-
sciousness and in extreme cases death.
- Do not breathe petrol/lubricating oil vapours and
exhaust gases.
- Operate the product outdoors only.
NOTE!
Product damage
Using the product without or with too little engine and
gearbox oil can result in engine damage.
- Fill with petrol and oil before commissioning. The
product is supplied without engine and gearbox oil.
NOTE!
Environmental damage!
Spilled oil can pollute the environment permanently.
The liquid is highly toxic and can quickly lead to water
pollution.
- Fill/empty oil only on level, paved surfaces.
- Use a filling nozzle or funnel.
www.scheppach.com GB | 37