Herunterladen Diese Seite drucken

Grundig VS 680 VPT Serviceanleitung Seite 89

Werbung

Zusatzlich erfolgt bei S-VHS-Betrieb Uber CIC
2950-(5), CT 2973, IC 2805-(14) die Umschal-
tung zwischen
NP und LP, wobei bei LP-
Betrieb ein High-Pegel an IC 2805-(14) an-
steht. Von der NLE-Stufe fir S-VHS,
CIC
2950-(9) gelangt das
BAS-Signal
an CIC
2850-(10).
Bei VHS-Betrieb gelangt das BAS-Signal dber
CD 2859 und die VHS-NLE-Stufe (CC 2859,
CR 2860) an CIC 2850-(11), wo es anschlie-
Bend zum direkten Signal addiert wird.
Um den Rauschanteil
zu vermindern
leitet
man das BAS-Signal uber CIC 2870-(4), ab-
hangig von der Betriebsart, Uber Pin 3, CR
2654, CC 2654 (S-VHS) oder Pin 5, CR 2655,
CC 2655 (VHS) dem Pin 34 des CIC 2850 zu.
Die Umschaltung erfolgt ber den S-VHS-
Status des |C 2805-(13). Im CIC 2850 durch-
lauftdas Signal einen Tiefpass und erreicht die
NC-Stufe (Noise Canceller), wo auch das nor-
male BAS-Signal von Pin 10 ansteht. Das vom
Rauschen befreite BAS-Signal durchlauft im
CIC 2850 noch eine Picture Control-Stufe
deren Wirksamkeit Uber R 2692 und CIC
2850-(36) einstellbar ist. An CIC 2850-(39)
steht ein rausch- und dropout-freies BAS-
Signal, das Gber S 8-5 der Crispening-Schal-
tung auf dem Videobaustein 1 zugefihrt wird
und tiber S 8-6 und Pin 40 wieder das CIC
2850 erreicht. Zwischen CIC 2850-(40) und -
(42) wird das BAS-Signal nochmals verstarkt
und Uber den Emitterfolger CT 2760 und S 6-
7 dem Chromabaustein zugefuhrt.
From the NLE-Stage for S-VHS, CIC 2950-(9)
the CVS signal is fed to CIC 2850-(10).
On VHS mode the CVS signal is fed via CD
2859 and the VHS-NLE stage (CC 2859, CR
2860) to CIC 2850-(11) in which it is added
subsequently to the direct signal.
To reduce the noise components the CVS
signal is fed from CIC 2870-(4), depending on
the operating mode, via Pin 3, CR 2654, CC
2654 (S-VHS) or Pin 5, CR 2655, CC 2655
(VHS) to Pin 34 of CIC 2850. The switchover
is carried out by the S-VHS-Status to IC 2805-
(13). In CIC 2850 the signal passes through a
Low Pass Filter and reaches the NC stage
(Noise Canceller), to which the normal CVS
signal from Pin 10 is also present. The noise
free CVS signal passes through a Picture
Control stage in CIC 2850 whose working
point is adjustable by R 2692 and CIC 2850-
(36). On CIC 2850-(39), a dropout and noise
free CVS signal is present and is fed from S 8-
5 to the Crispening Stage on the Video Module
1 and also via S 8-6 and Pin 40 back to CIC
2850. Between CIC 2850-(40) and -(42) the
CVS signal is amplified again and then fed to
the Chroma Module via the emitter follower CT
2760 and S 6-7.
tazione non lineare viene commutata a secon-
da del funzionamento VHS 0 S-VHS tramite IC
2805-(11), CT 2965, CIC 2950-(7):
VHS: IC 2805-(11) - High;
S-VHS: IC 2805-(11) - Low.
Inoltre, in funzionamento
S-VHS,
attraverso
CIC 2950-(5), CT 2973, IC 2805-(14), avviene
la commutazione tra NP (Normai-Play) ed LP
(Long-Play), per la quale in funzionamento LP
si forma un livello High su IC 2805-(14). Dallo
stadio NLE per S-VHS, CIC 2950-(9), il segna-
le BAS giunge al CIC 2850-(10). In funziona-
mento VHS, il segnale BAS giunge attraverso
CD 2859 e lo stadio NLE VHS (CC 2859, CR
2860), all'integrato CIC 2850-(11), dove viene
sommato al segnale diretto.
Per limitare la componente di fruscio, si invia il
segnale BAS prelevato da CIC 2870-(4), in
base al tipo di funzionamento, al pin 34 di CIC
2850, tramite pin 3, CR 2654, CC 2654 (S-
VHS) 0 pin 5, CR 2655, CC 2655 (VHS). La
commutazione
avviene mediante
IC 2805-
(13) in situazione S-VHS.
Nel CIC 2850, il
segnale percorre un passabasso e raggiunge
lo stadio NC (Noise Canceller) dove si trova
anche il normale segnale BAS applicato al pin
10. !l segnale BAS privo del fruscio attraversa
in questintegrato anche uno stadio di control-
lo dell'immagine, la cui azione é regolabile con
R 2692 e CIC 2850-(36). In CIC 2850-(39) si
trova un segnale BAS sgombro darumore eda
dropout il quale, tramite S 8-5, viene inviato al
circuito Crispening nel modulo video 1 ed
attraverso S 8-6 ed il pin 40 ricondotto al CIC
2850. Tra CIC 2850-(40) e -(42), il segnale
BAS viene nuovamente amplificato e, tramite
linseguitore d'emittitore CT 2760
e S 6-7,
inoltrato al modulo croma.
95

Werbung

loading