Understanding The "Settings" Sub-Menu; Selecting The Display Language - Hürner HWT 400–WeldControl Bedienungsanleitung

4.1.2 Understanding the "Settings" Sub-menu

"Check Code Expiry on" means that the welder identification code has
to be current and not expired (default period of validity 2 years
from code issuance), or the welding operation cannot be started,
"off," that the validity of the code is not checked at all.
"Memory Control on" means that when the system memory is full of
reports, the unit will be blocked until the reports are printed or
downloaded, "off," that it works but that the oldest report will
be overwritten.
"Automode on" means that in butt-welding operations the Automode
feature for the easy management of the welding process (see
Sect. 4.3.4) can be used, "off," that the feature is not available.
"Manual Input on" means that the manual input of welding param-
eters or computed parameters is possible, "off," that the manual
input is not allowed.
"Check Ambient Temperature on" means that the outside tempera-
ture is measured before welding, "off," that it not; if the tem-
perature is below 0°C (32°F), welding should be performed only
after taking appropriate steps (heating, tent, for instance).
"Additional Cylinder on" means that the supporting cylinder that
ensures better positional stability of the components during
facing and jointing in operations > 250 mm will be installed on the
clamps and used (see Sect. 3.3, 4.3.4 ff.), "off," that it will not be
used and is not connected to the hydraulic circuit of the system.
"Welder Code Options – M – " means that by pressing the MENU
key, the user can access a sub-menu that allows determining
when the welder code, if it is enabled at "Recording," has to be
entered:always, i. e. before evey single welding operation, only
before the first welding operation after switching the unit on or
only after the first welding operation of a new day/date.
"Language – M – " means that by pressing the MENU key, the user
can access a sub-menu for selecting the display and report lan-
guage (see Sect. 4.1.3).
"Date/Time – M – " means that by pressing the MENU key, the user
can access a sub-menu for setting the clock (see Sect. 4.1.4).
"Buzzer Volume – M – " means that by pressing the MENU key, the
user can access a sub-menu for setting the volume of the status
buzzer (see Sect. 4.1.5).
"Temperature Unit – M – " means that by pressing the MENU key, the
user can access a sub-menu for selecting centigrade or Fahrenheit
as the unit for the temperature.
"Pressure Unit – M – " means that by pressing the MENU key, the user
can access a sub-menu for selecting bars or pounds per square
inch (psi) as the unit for the pressure.
"Length Unit – M – " means that by pressing the MENU key, the user
can access a sub-menu for selecting millimeters or inches as the
unit for the length.
"Inventory Number – M – " means that by pressing the MENU key,
the user can access a sub-menu for entering the number under
which the unit is inventorized with the operating company.
"Number of Tags – M – " means that by pressing the MENU key, the
user can access a sub-menu for entering the number of tags that
are printed automatically after welding with the optional label
tag printer if such a printer is connected.
"Standard – M – " means that by pressing the MENU key, the user can
access a sub-menu for selecting the standard (guideline, norma-
tive scheme) applicable to the welding operation.

4.1.3 Selecting the Display Language

When the "Select Language" sub-menu was selected, the screen
changes and the display reproduced in Display 6 appears.
16
EN
HÜRNER HWT 400–WeldControl User's Manual
H Ü R N E R S c h w e i s s t e c h n i k G m b H
Nieder-Ohmener Str. 26
35325 Mücke, Germany
SETTINGS
***
Check Code Exp. Off
Memory Control
>Automode
Version January 2020
***
On
On
Display 5