Recording - Yamaha DSP-Z9 Bedienungsanleitung

RUNNING H/F 1
You can use the REC OUT/ZONE 2 control to record one
source while watching and/or listening to another source.
Recording adjustments and other operations are
performed from the recording components. Refer to the
operating instructions for these components.
.
PURE DIRECT
REC OUT/ZONE 2
SOURCE/REMOTE
DTV/LD DVD
CABLE MD/TAPE
SPEAKERS
2CH/MULTI CH
A B SAT CD-R
INPUT SELECTOR
VCR 1 CD
TUNER
VCR 2
DVR PHONO
VIDEO AUX
STANDBY
/ON
SILENT OPTIMIZER
MIC
PHONES
1 2
1
Turn on this unit's power and all connected
components.
2
Select the source component you want to
record from by using REC OUT/ZONE 2.
• To record the current input source you are watching
or listening to, set REC OUT/ZONE 2 to
SOURCE/REMOTE.
REC OUT/ZONE 2
SOURCE/REMOTE
DTV/LD
CABLE
SAT
VCR 1
VCR 2
DVR
VIDEO AUX
• To record a source other than the one you are
watching or listening to, set REC OUT/ZONE 2 to
the source you want to record.
REC OUT/ZONE 2
SOURCE/REMOTE
DTV/LD
CABLE
SAT
VCR 1
VCR 2
DVR
VIDEO AUX
After making this setting, you can change the source
you are listening to and/or watching without affecting
the recording by rotating INPUT (or pressing one of
the input selector buttons on the remote control).
Note
The source you record and the source in Zone 2 are always
identical.
46

RECORDING

VOLUME
MULTI JOG
BALANCE
MULTI CH DSP
INPUT MODE INPUT STRAIGHT PROGRAM
TONE
CONTROL
EFFECT
VIDEO AUX
S VIDEO VIDEO L AUDIO R OPTICAL
DVD
MD/TAPE
CD-R
CD
TUNER
PHONO
DVD
MD/TAPE
CD-R
CD
TUNER
PHONO
3
Start playback (or select a broadcast station)
on the source component.
4
Start recording on the recording component.
y
To record audio and video from different sources, set REC OUT/
ZONE 2 to SOURCE/REMOTE, select a video source first, then
select an audio source (see page 39).
Notes
• Do a test recording before you start an actual recording.
• When this unit is set in the standby mode, you cannot record
between other components connected to this unit.
• The setting of TONE CONTROL, VOLUME, "Speaker Level"
(page 69) and programs does not affect the recorded material.
• A source connected to this unit's MULTI CH INPUT jacks
cannot be recorded.
• S video and composite video signals pass independently
through this unit's video circuits. Therefore, when recording or
dubbing video signals, if your video source component is
connected to provide only an S video (or composite video)
signal, you can record only an S video (or composite video)
signal to your VCR.
• A given input source is not output on the same REC OUT
channel. (For example, the signal input from VCR 1 IN is not
output on VCR 1 OUT.)
• Check the copyright laws in your country to record from
records, CDs, radio, etc. Recording of copyrighted material may
infringe copyright laws.
• Dolby Digital RF signals are not output from the DIGITAL
OUTPUT jacks.
• Signals input through an i.LINK connection are only output to
the DIGITAL OUTPUT jacks when REC OUT/ZONE 2 is set
to SOURCE/REMOTE (priority is given to input signals from
the OPTICAL and COAXIAL jacks).
• Audio signals from CD or DVD video discs input through an
i.LINK connection are only output if they come un-encrypted
from the playback device. In other words, copy-protected
signals input through an i.LINK connection will not be output
to the REC OUT jacks.
If you play back a video source that uses scrambled or
encoded signals to prevent it from being dubbed, the
picture itself may be disturbed due to those signals.