Assigning I.link Components; Listening To Playback From An I.link Component - Yamaha DSP-Z9 Bedienungsanleitung

Assigning i.LINK components

When an i.LINK component is connected, this unit
automatically recognizes the connection and registers the
connected component. Registered i.LINK components,
such as CD or DVD players, can be assigned to a specific
input. Assigning an i.LINK component to a specific input
allows you to select the video input signals from that
component together with the audio signals received via the
i.LINK connection for simultaneous playback.
Notes
• If you connect an i.LINK component that does not support
i.LINK (AUDIO), or an i.LINK component that does not
support audio signal transmission, the connected component
will be registered with this unit, but cannot be assigned to a
specific input.
• i.LINK components without a vendor or model name, such as
IEEE1394 repeater/hub, are not registered.
PURE DIRECT
REC OUT/ZONE 2
SOURCE/REMOTE
DTV/LD DVD
CABLE MD/TAPE
SPEAKERS
2CH/MULTI CH
A B SAT CD-R INPUT MODE
INPUT SELECTOR
VCR 1 CD
TUNER
VCR 2
DVR PHONO
VIDEO AUX
STANDBY
/ON
SILENT OPTIMIZER
MIC
PHONES S VIDEO
1 2 3
1
Turn on the power for this unit and the
connected i.LINK component.
The i.LINK component is automatically recognized.
"Link Check" flashes on the front panel display
during this procedure.
MULTI CH V–AUX DVR VCR 2 VCR 1 SAT CABLE
i . L I N K I n f o .
L i n k C h e c k
After the i.LINK component is recognized, the name (model
number) and name of the assigned input are displayed.
MULTI CH V–AUX DVR VCR 2 VCR 1 SAT CABLE
D V D - A A A A A
- >
MULTI CH V–AUX DVR VCR 2 VCR 1 SAT CABLE
i . L I N K A s s i g n ?
- > I n p u t S e l e c t o r
VOLUME
MULTI JOG BALANCE
MULTI CH DSP
INPUT STRAIGHT PROGRAM
TONE
CONTROL
EFFECT
VIDEO AUX
VIDEO L AUDIO R OPTICAL
CD
DTV/LD DVD MD/TAPE CD–R TUNER PHONO
VOLUME
LFE
L C R
SL SR
DTV/LD DVD MD/TAPE CD–R TUNER CD PHONO
VOLUME
LFE
D V D
L C R
SL SR
CD
DTV/LD DVD MD/TAPE CD–R TUNER PHONO
VOLUME
LFE
L C R
SL SR
2
Rotate INPUT SELECTOR to select the input
to which you want to assign the i.LINK
component.
3
After selecting, press PURE DIRECT to
complete the assignment.
If two or more i.LINK components are connected
simultaneously, repeat steps 2 and 3 to assign input
for the other i.LINK components.
y
• If you do not want to assign a specific input, select
"MULTI CH" in step 2, then press PURE DIRECT. If you do
this, the i.LINK component is assigned to MULTI CH INPUT.
Even after you assign the i.LINK component to a specific input,
you can still use MULTI CH INPUT to select i.LINK (AUDIO)
components using INPUT SELECTOR.
• After recognition in step 1 is complete, the i.LINK component
is automatically assigned to MULTI CH INPUT if no operation
is performed within 10 seconds.
• You can change the input assignment using the i.LINK Select
menu (see page 99).
Listening to playback from an
i.LINK component
Perform the following steps to listen to playback from a
registered i.LINK component.
If the i.LINK component has been assigned to a
specific input
1
Rotate INPUT SELECTOR to select the input
assigned to the i.LINK component.
2
Press INPUT MODE repeatedly to set "Auto"
or "i.LINK" as the input mode.
MULTI CH V–AUX DVR VCR 2 VCR 1 SAT CABLE
I n p u t
A u t o : - - -
MULTI CH V–AUX DVR VCR 2 VCR 1 SAT CABLE
I n p u t
i . L I N K : - - -
3
Start playback on the connected i.LINK
component.
Refer to the operating instructions supplied with the
component.
USING i.LINK
DTV/LD DVD MD/TAPE CD–R TUNER CD PHONO
VOLUME
D V D
LFE
L C R
SL SR
or
DTV/LD DVD MD/TAPE CD–R TUNER CD PHONO
VOLUME
D V D
LFE
L C R
SL SR
97