Unold BACKMEISTER EDEL 68456 Bedienungsanleitung Seite 36

degree of browning with the BROWNING button. In the
example we will use program 1 = Basic. The program ends
at 7 AM. Then bread will be kept warm for one hour.
Therefore, in order to take out warm, fresh bread at 7:00
AM, in the evening around 8:30 PM you must increase
the program time to 10 hours 30 minutes by repeatedly
pressing the TIME button. To do so, press the „TIME +" and
„TIME -" buttons. The maximum pre-select is 15 hours.
After the timer has been set, press the START/STOP button
to start the time-delayed baking program. The time symbol
flashes until the program starts. The time still remaining
will be shown in the display.
To interrupt the time pre-select, press the START/STOP
button for at least 3 seconds. You can then change the
time pre-select as needed, or start immediately with the
bread baking.
Please note:
When using the timer delay function, do not bake with
perishable ingredients, such as milk, eggs, fruit, yogurt,
onions, etc.
PAUSE
The PAUSE button can be used to briefly interrupt the pro-
gram, for example, to remove the kneader from the dough
or to brush the surface of the bread with water or milk.
Press the PAUSE button to interrupt the running program.
As long as the time display is flashing, the program is in
the pause function. Now, for example, you can remove the
kneader or brush the surface of the bread as desired. Then
close the lid. To end the pause, press the PAUSE button
again. The time display stops flashing and the program
continues. Caution: Only interrupt the program briefly, for
not more than approx. 5 minutes. Longer interruptions can
affect the rising of the dough and ruin the bread.
USER PROGRAMS
In addition to the other numerous programs provided by the
Backmeister also offers two programs that we have named
®
USER PROGRAM and USER PROGRAM GLUTEN-FREE,
because you can program them yourself. You can change
the basic time and program phase settings as programmed
at the factory or leave out various program phases entirely.
This allows you to develop your own individual program for
baking bread or preparing dough. First you should become
familiar with the following information on the basic
programming and use of the USER PROGRAM.
USER PROGRAMMING
Both programs have the following selection possibilities
BROWNING adjustable
Timer adjustable
Levels I and II not adjustable
The pre-programmed sequence is the same as for the
BASIC program. The programmed times of the sequence
are - as specified - adjustable.
USER PROGRAM STANDARD (user program 1)
Phase Pre-set
Total time 3:00 hours
1st kneading 10 minutes
1st rising 20 minutes
36
Adjustable time frame
6-14 minutes
20-60 minutes
2nd 15 minutes
kneading
2nd rising 25 minutes
3rd rising 45 minutes
Baking 65 minutes
Keeping 60 minutes
warm
USER PROGRAM GLUTEN-FREE (user program 2)
Phase Pre-set
Total time 3:00 hours
1st kneading 10 minutes
1st rising 20 minutes
2nd 15 minutes
kneading
2nd rising 25 minutes
3rd rising 45 minutes
Baking 65 minutes
Keeping 60 minutes
warm
Proceed as follows:
Select the desired USER PROGRAM with the respective
button. Select the desired phase with the USER
PROGRAM 1 or 2 button. The symbol for kneading 1 and
the programmed time 0:10 for this phase 0:10 appear on
the display.
The set time can be adjusted via the buttons „TIME +" and
„TIME -". Press the button repeatedly until the desired
time appears on the display (beyond „0", if necessary).
Save the change with the button USER PROGRAM 1 or 2.
Press this button again and the next program phase and
the programmed time will appear on the display: (Rise 1
and 0:20).
If the maximum programmable time for the respective
program phase is exceeded by pressing the buttons „TIME
+" and „TIME -" will appear on the display if this is possible
according to the above listing. This phase is then skipped
during the program.
Each programming (adjustment) must be saved by pressing
the USER PROGRAM 1 or 2 button, so that the next
program phase can be programmed.
Once you have programmed all phases to suit your
preferences, conclude the programming by pressing the
START/STOP button. The programmed time for the user
program appears on the display. The program then starts
either immediately or after the time set via the timer
function.
5-20 minutes
5-120 minutes
0-120 minutes
10-80 minutes
0-60 minutes
Adjustable time frame
0-45 minutes
20-60 minutes
5-20 minutes
5-120 minutes
0-120 minutes
10-100 minutes
0-60 minutes