Coltene BioSonic UC150 Benutzerhandbuch Seite 13

00 vector graphics: single-icons and screen buttons
30-settings
• A symbol will be displayed on the top of main screen if heater is selected ON. The heater will
31-temperature-large
now function during the selected cleaning cycle.
32-temperature-medium
00 vector graphics: single-icons and screen buttons
33-temperature-small
• Select "HEATER OFF" if heating is not desired.
34-program-light
30-settings
35-program-regular
• A blinking symbol on the main screen is displayed while the heating is in progress during a
31-temperature-large
36-program-heavy
cleaning cycle. Current temperature information will always be displayed at the top of the LCD
32-temperature-medium
37-program-my
display.
33-temperature-small
38-timer-medium
34-program-light
39-timer-large
NOTE: The heater will not turn on until a cleaning cycle has been initiated. It is, therefore,
35-program-regular
40-solution
recommended that a pre-cycle (with heater activated) be performed when a specific temperature
36-program-heavy
41-degas
is desired. The cycle can be run without cleaning load and the length of the cycle would depend
37-program-my
on the desired temperature.
hot surface
38-timer-medium
39-timer-large
NOTE: The user can change the temperature unit from ºC to ºF using the settings menu.
40-solution
41-degas
9. Cleaning Methods
hot surface
It is the responsibility of the user to verify that a cleaning cycle is effective. The
user must inspect all devices for a satisfactory level of cleaning before continuing
to the next step in the infection control process.
WARNING!
In Tank
Basket Cleaning: Place parts to be cleaned into the basket or use cassettes.
the basket directly into the tank containing BioSonic General Purpose, Germicidal, or Enzymatic
Cleaner. Follow dosage instructions per cleaning solution label. After cleaning, rinse the basket
and instruments thoroughly under running water.
In Beaker
For specialized item cleaning (e.g. prostheses, burs): Place items into a beaker and add desired
cleaning solution (e.g. BioSonic® Cement Remover or BioSonic® General Purpose) according to
the product directions. Suspend the beaker in the tank by using the beaker holder and place the
beaker positioning ring around the beaker so that the bottom 2/3
NOTE: Beaker holder is to be used in conjunction with the basket
removing basket if beakers are left in place.
*see last page for figures
42-log
43-information
44-close-lid
45-lid-is-open
46-lid-was-open
42-log
47-repair
43-information
48-software-update
44-close-lid
50-A-button-standby
50-B-button-standby-feedback
45-lid-is-open
51-statusbar-standby-closed
52-statusbar-standby-opened
46-lid-was-open
60-attention
47-repair
61-instructions
48-software-update
62-A-button-ok
50-A-button-standby
62-B-button-ok-feedback
50-B-button-standby-feedback
warning/caution
51-statusbar-standby-closed
52-statusbar-standby-opened
60-attention
61-instructions
62-A-button-ok
62-B-button-ok-feedback
warning/caution
20-A-button-checked
20-B-button-checked-feedback
21-A-button-save
21-B-button-save-feedback
22-A-button-home
22-B-button-home-feedback
23-A-button-back
20-A-button-checked
23-B-button-back-feedback
20-B-button-checked-feedback
24-A-button-download
21-A-button-save
24-B-button-download-feedback
21-B-button-save-feedback
25-A-button-play
22-A-button-home
25-B-button-play-feedback
22-B-button-home-feedback
26-A-button-pause
23-A-button-back
26-B-button-pause-feedback 23-B-button-back-feedback
24-A-button-download
24-B-button-download-feedback
CB
M 1:1
20.10.2016
25-A-button-play
25-B-button-play-feedback
26-A-button-pause
26-B-button-pause-feedback
20.10.2016
(Figure 8*)
is suspended in the main bath.
rds
(Figure 7*). Use caution when
CB
M 1:1
Then place
13