Coltene BioSonic UC150 Benutzerhandbuch Seite 12

• The BioSonic UC150 should always be covered while operating to trap aerosols in the tank. The
BioSonic UC150 is equipped with a hinged cover for easy one hand opening. The cover also
conveniently lifts off for cleaning in spaces with low cabinets above the unit.
• Do not place additional instruments into a cleaning load mid-cycle. The additional instruments
may not be cleaned as effectively as those in the original load. Additional instruments may also
impact the cleaning efficacy of the original load by covering soiled instruments and increasing
the mass of the load.
Heater Operation
Certain models of the BioSonic UC150 are equipped with a heater to accelerate heating of the
solution in the tank. Selecting a temperature instructs the heater to activate during the next
cleaning cycle and remain active until the temperature is reached.
NOTE: The heater feature is not designed to maintain the selected temperature, but rather
activate at the start of the next cleaning cycle and deactivate once the set temperature is
reached. Thermostatic control is not a feature of the BioSonic UC150.
00 vector graphics: single-icons and screen buttons
CAUTION!
Activate the Heat Feature
In order to obtain the activation code, visit http://biosonic.coltene.com or email customer service
at info.us@coltene.com or info.ch@coltene.com.
NOTE: The temperature in the tank is displayed in the top bar of the LCD screen. Pressing the
key to activate this feature will bring up a new screen on the display. The first time this feature is
activated, the user must enter the activation code. Press
function will now be available for use.
01-logo-loading
Set the Desired Temperature
00 vector graphics: single-icons and screen buttons
02-logo-information • Press the
• Select "HEATER ON" to activate heating function. Press
12
The heating function of the BioSonic UC150 (if enabled) takes place until the set
temperature is reached only. If the set temperature is reached before the end of
the cleaning cycle, the heater will shut off, but the cycle will continue. Through
prolonged use, the natural cavitation process will continue to heat the solution
beyond the desired temperature, but at a decreased rate without the heater.
When this happens, the unit is still functioning properly.
30-settings
31-temperature-large
32-temperature-medium
33-temperature-small
34-program-light
35-program-regular
36-program-heavy
37-program-my
38-timer-medium
39-timer-large
40-solution
03-product-name
41-degas
button. Set the temperature between 25°C (75°F) and 60°C (140°F). 09-1-A-button-heater- rst
09-2-A-button-heater-after-code
09-B-button-heater-feedback
hot surface
10-A-button-solution-degas
30-settings
10-B-button-solution-degas-feedback
12-A-button-language-measurest
31-temperature-large
12-B-button-language-measures-feedback
32-temperature-medium
13-A-button-date-time
13-B-button-date-time-feedback
33-temperature-small
14-A-button-my-setup
42-log
43-information
44-close-lid
45-lid-is-open
46-lid-was-open
47-repair
48-software-update
50-A-button-standby
50-B-button-standby-feedback
51-statusbar-standby-closed
52-statusbar-standby-opened
60-attention
61-instructions
62-A-button-ok
62-B-button-ok-feedback
warning/caution
42-log
43-information
44-close-lid
45-lid-is-open
20-A-button-checked
20-B-button-checked-feedback
21-A-button-save
21-B-button-save-feedback
00 vector graphics: logo and buttons
22-A-button-home
22-B-button-home-feedback
01-logo-loading
23-A-button-back
23-B-button-back-feedback
02-logo-information
24-A-button-download
24-B-button-download-feedback
04-A-button-program-light
04-B-button-program-light-feedback
once the code is entered. The heating 25-A-button-play
25-B-button-play-feedback
05-A-button-program-regular
05-B-button-program-regular-feedback
26-A-button-pause
06-A-button-program-heavy
26-B-button-pause-feedback
06-B-button-program-heavy-feedback
07-A-button-program-my
07-B-button-program-my-feedback
11-A-button-settings
20.10.2016
11-B-button-settings-feedback
08-A-button-log
to accept the temperature. 20-A-button-checked
08-B-button-log-feedback
20-B-button-checked-feedback
21-A-button-save
21-B-button-save-feedback
22-A-button-home
CB
M 1:1
0
0
0
0
1
1