Deleting A Configuration; Memory Chip Card; Security Adjustments (Security Utilities); Concealing Parameters - IMG STAGE LINE DSM-480LAN Bedienungsanleitung

ration has yet been memorized, the message
GB
shortly appears:
No Stored Programs.
4) Use the rotary knob PM1/ ENTER to select
one of configurations memorized and press
the knob to confirm. To load the configuration
[Enter] to Re call
(indication:
the knob ENTER once again (or cancel the
procedure by pressing the knob ESC).
During loading, the display shows:
Loading New Program....
5) To exit the submenu, press the knob ESC.
After exiting the menu, the name of the last con-
figuration loaded is displayed.

5.5.3 Deleting a configuration

To delete a configuration not required any more
from the memory of the DSM-480LAN:
1) To call the menu, press the knob UTILITY (5).
System Utilities
2) Use the rotary knob PM1/ ENTER (2) to
select the menu item
ties
and press the knob to confirm.
3) Use the rotary knob PM1/ ENTER to select
Delete a Program
the menu item
press the knob to confirm.
4) Use the rotary knob PM1/ ENTER to select
the memory location to be deleted and press
the knob to confirm. To delete the configura-
[Enter] to Delete
tion (indication:
press the knob ENTER once again (or cancel
the procedure by pressing the knob ESC).
During deleting, the display shows:
Deleting Program....
5) To exit the submenu, press the knob ESC.

5.5.4 Memory chip card

As an extension of the memory locations in the
unit, for data back-up or for the transfer of con-
figurations between two units it is possible to
memorize 24 configurations on the supplied
memory chip card. It is also possible to access
the card when the DSM-480LAN is remotely
controlled via a computer (
1) Insert the card with the contacts showing
upwards into the slot PC CARD (3).
PC CARD
2) To call the menu, press the knob UTILITY (5).
System Utilities
3) Use the rotary knob PM1/ ENTER (2) to select
Memory Card Utili-
the menu item
ties
and press the knob to confirm.
4) As described for the internal storage in chap-
ters 5.5.1 to 5.5.3, it is possible to memorize
a configuration on the card, to load a config-
uration from the card or to delete it via the
submenus
Save a Program
,
Recall a Program
Delete a Program.
If there is no card in the unit, the following
error message is shown:
Error: Card not inserted
30
5.6 Security adjustments
(Security Utilities)
The DSM-480LAN can be locked against acci-
dental misadjustment and unauthorized opera-
tion. It is possible to define if the adjustments are
to be visible or concealed when the unit is
locked.
), press

5.6.1 Concealing parameters

To define if the adjustments are to be visible or
concealed when the unit is locked:
1) To call the menu, press the knob UTILITY (5).
System Utilities
2) Use the rotary knob PM1/ ENTER (2) to
select the menu item
ties
3) Confirm the menu item
by pressing the knob ENTER.
4) Use the rotary knob PM2 (4) to define if the
is shown.
adjustments are to be visible (
will be shown
Program Utili-
meter will not be shown
unit is locked. The present adjustment is
marked
and
5) Confirm the selection by pressing the knob
ENTER or cancel the procedure by pressing
the knob ESC.
6) To exit the submenu, press the knob ESC.
),

5.6.2 Locking the unit

To lock the unit against accidental misadjust-
ment:
1) To call the menu, press the knob UTILITY (5).
System Utilities
2) Use the rotary knob PM1/ ENTER (2) to select
the menu item
and press the knob to confirm.
3) Use the rotary knob PM1/ ENTER to select
the menu item
knob to confirm. The display shows:
Lock : Off
(unit not locked)
chapter 6.8.5).
4) Use the rotary knob PM2 (4) to change the
adjustment to:
Lock : On
(lock the unit)
5) Confirm the selection by pressing the knob
ENTER or cancel the procedure by pressing
the knob ESC.
The display shows the symbol
in this way. Now it is not possible any more to
change the adjustments or to mute inputs or out-
is displayed.
puts. It depends on the preadjustment "Show
Parameter" (
for the inputs or outputs are visible.

5.6.2.1 Unlocking the unit

To unlock the unit:
1) Press the knob UTILITY (5). The display
shows:
Lock Unit
Lock : On
,
2) Use the rotary knob PM2 (4) to select
Lock : Off
confirm.
3) To exit the submenu, press the knob ESC.
is shown.
Security Utili-
and press the knob to confirm.
Show Parameter
Parameter
Para-
) or concealed (
) when the
*
.
is shown.
Security Utilities
Lock Unit
and press the
*
Ƈ
for a unit locked
chapter 5.6.1) if the adjustments
*
and press the knob ENTER to

5.6.3 Locking the unit with a password

The unit can be protected against unauthorized
operation with a password. When delivered and
after the reset of the unit ( chapter 5.7) the fol-
000000
lowing password applies:
To make an unauthorized access difficult, it is
indispensable to change this password.

5.6.3.1 Changing a password

1) To call the menu, press the knob UTILITY (5).
System Utilities
is shown.
2) Use the rotary knob PM1/ ENTER (2) to
Security Utili-
select the menu item
ties
and press the knob to confirm.
3) Use the rotary knob PM1/ ENTER to select
User Password
the menu item
the knob to confirm. The display shows:
User Password
[_ ]
The flashing underscore marks the position
for inserting the first character.
4) Enter the present password:
Use the rotary knob PM2 to change the flash-
ing character. Use the rotary knob PM1 to
select the position of the next character to be
entered in each case.
5) To terminate the input, press the knob
ENTER.
When entering an invalid password, the
following message appears:
Password Wrong!
In this case repeat the input from step 3).
When entering a valid password, the fol-
lowing message appears:
New Password
[_ ]
6) Enter the new password here and press the
knob ENTER to confirm. A password may
consist of 6 characters as a maximum.
Note: To make unlocking of the unit possible
even when the unit is remotely controlled via
a computer, the password should only con-
sist of upper-case letters and lower-case let-
ters from the ASCII character set, numbers
and blanks.
7) To exit the submenu, press the knob ESC.
5.6.3.2 Locking the unit
1) To call the menu, press the knob UTILITY (5).
System Utilities
is shown.
2) Use the rotary knob PM1/ ENTER (2) to
System Utili-
select the menu item
ties
and press the knob to confirm.
3) Use the rotary knob PM1/ ENTER to select
Enable Password
the menu item
press the knob to confirm. The display
shows:
Enable Password:
[_ ]
The flashing underscore marks the position
for inserting the first character.
4) Enter the password:
Change the flashing character with the rotary
knob PM2. Select in each case the position of
the next character to be entered with the
rotary knob PM1.
5) To terminate the input, press the knob
ENTER.
and press
and