MADRIX 3 PLEXUS User Manual / Handbuch Table Of Contents / Inhaltsverzeichnis I MADRIX PLEXUS User Manual (English) 1 Overview ........................... 6 2 MADRIX PLEXUS (Hardware) ........................... 8 LCD Graphics Display (PLEXUS Menus) ................................9 Connectivity (Top And Bottom Connections) ................................
Seite 3
4 MADRIX PLEXUS (Firmware) ........................... 270 Firm w are-Versionshinw eise ................................271 Aktualisieren der Firm w are ................................279 MADRIX PLEXUS Updater (Zusatzprogram m ) ................................282 5 Häufig gestellte Fragen (FAQs) ........................... 285 6 Hilfe und Fehlerbehebung ........................... 287 7 Impressum und Urheberrecht ...........................
The MADRIX PLEXUS is a USB 2.0 DMX512 interface. The MADRIX PLEXUS controls up to 2 universes per unit via DMX512 or Art-Net as a versatile stand-alone interface or live controller. It is the first interface to offer stand-alone playback of MADRIX light shows and effects.
Others Blinking/ 'Highlight Device' is active in the Device Manager of MADRIX. Flashing (Flashing can be stopped by pressing a button on the PLEXUS device.) Display How To How To Navigate Through Menus Press 'OK' to open the menu bar. Then, navigate with the help of the arrow buttons. When you have selected your target menu, press 'OK' to enter it.
Seite 12
Configuration. Timers Navigate to the menu 'Stand-Alone' > 'Timers'. All Timers of your current PLEXUS Configuration are listed in this menu. Select a specific Timer with You can check the Type, the Start time, and validity of the Timers (Valid From and Valid Thru).
Seite 13
Please note: You may reset to default values (100%) by pressing ' and ' or ' and ' at the same time for 2 seconds. You can also configure the settings in the PLEXUS Configuration window in MADRIX. For more information, see Managing Devices Further.
DMX-over-Ethernet, are shown. More specifically, this menu contains the universe settings. Technically speaking Art-Net universes range from 0 to 255, but they are displayed on the PLEXUS and in MADRIX from 1 to 256. 'Art-Net -> DMX 1' sets which received Art-Net universe is sent to the first XLR port for DMX output (DMX 1).
Seite 15
MADRIX PC to your PLEXUS device using network cables. In Live Mode, you would then send data over the network to the PLEXUS and the PLEXUS outputs the data to each XLR port, where your LED fixtures, LED controllers, or LED drivers would be connected.
Managing Devices Further. You may change the settings in this menu, on the device (How To Edit Values). You can also configure the settings in the PLEXUS Configuration window in MADRIX. For more information, see Managing Devices Further. IP Address Navigate to the menu 'Network' >...
Seite 17
MADRIX PLEXUS User Manual (English) You may change the settings and the functionality. Press and hold 'OK' for 2 seconds. 'Show As' - Choose the overall display modus (Graphic, Table, Channel). 'Show Values As' - Choose the display modus of values (Hexadecimal, Decimal, Percent).
Seite 18
MADRIX 3 PLEXUS User Manual / Handbuch Please note: You may reset the DMX value to its default value by pressing ' or ' at the same time for 2 seconds. You may change the settings and the functionality. Press and hold 'OK' for 2 seconds.
Seite 19
The PLEXUS menu 'Remote Control' contains 2 entries. Remote Options Navigate to the menu 'Remote Control' > 'Remote Options'. You can send DMX or Art-Net values directly to the MADRIX PLEXUS. In this way, you can control the PLEXUS remotely using a certain set of remote functions.
MADRIX 3 PLEXUS User Manual / Handbuch Monitor Remote Navigate to the menu 'Remote Control' > 'Monitor Remote'. Use this menu to monitor and check incoming DMX data for Remote Control (DMX 1 or DMX 2). All 20 channels can be monitored using hexadecimal values.
Seite 21
Black background and a white font are the default settings. You may change the settings in this menu, on the device (How To Edit Values). You can also configure the settings in the PLEXUS Configuration window in MADRIX. For more information, see Managing Devices Further.
Seite 22
PLEXUS Configuration. The default settings is Enabled. 'Ports' - can be 'Enabled' or 'Disabled'. This activates or deactivates all Ports on the device globally, even if they are configured in your PLEXUS Configuration. The default settings is Enabled. You may change the settings in this menu, on the device (How To Edit Values).
Control Buttons 1.2.3 Navigation And Editing The five control buttons are mainly used to select and enter menus on the PLEXUS device or in order to edit settings. Here are the general How To's again: How To Navigate Through Menus Press 'OK' to open the menu bar.
MADRIX PLEXUS User Manual (English) Button Assignment If you want, you can enable the option 'Rotate 180°' in the PLEXUS menu 'Settings' > 'Device'. This will rotate the display by 180°. The displayed menus will therefore be shown upside down.
The integrated SD card slot is located at the top of the device. In order to access it, please open the metal lid first (See 'How To Open The Metal Lid' on page 6 of the MADRIX PLEXUS Quick Start Guide).
MADRIX PLEXUS User Manual (English) File System If you need to prepare an SD card to be used with your MADRIX PLEXUS or if you would like to clear up your currently used SD card, you may reformat the SD card in Windows.
Extension port specifications: 15-pin, D-Sub, US, female In MADRIX, please open the menu 'Tools' > 'PLEXUS Configuration… ' > 'Extension Ports' to configure each port individually for the corresponding PLEXUSConfiguration. Select a PLEXUS Configuration first. For more information, see Stand-Alone Mode.
You can connect different equipment to these Ports. In general, the Port can work as an input to receive a signal from external equipment. According to your PLEXUS Configuration, it can then trigger a certain action/behavior. Or it can function as output to send a signal to the external equipment, which then can process this signal.
MADRIX PLEXUS User Manual (English) Remote Control 1.2.6 Control Buttons A limited option to control the PLEXUS is to use the control buttons on the device during stand- alone playback. For more information, see Control Buttons. DMX-IN DMX-IN is a way to control the MADRIX software remotely. Learn more about this topic in the...
Incoming DMX data would then additionally be sent through to Art-Net. You may change the settings in this menu, on the device (How To Edit Values). You can also configure the settings in the PLEXUS Configuration window in MADRIX. For more information, see Managing Devices Further.
Seite 39
MADRIX PLEXUS User Manual (English) Function Useful Useful Description Values Live Stand- Mode Alone Mode Scene I 0 - 255 will select a specific Scene. Works in combination with function Scene II. Values of Scene I will be added to function Scene II.
Seite 40
MADRIX 3 PLEXUS User Manual / Handbuch Off: < 128 Stop will interrupt and stop playback. > 127 Off: < 128 Intensity 0 - 255 will change the Brightness level from 0% to a 0 - 100% maximum of 100%. The default value is 100%.
Seite 41
Example: You may wish to exclude Red color values from your visual effects via Remote Control. Using the Remote Command 13 (Intensity Group 1), you can choose to reduce the Red color channel to 0, for example. In this way, the PLEXUS will continue to output your visual effects, but completely without Red.
Seite 42
But if for some reason Direct Remote Control via DMX-IN or Art-Net is not available anymore, you can use different PLEXUS Menus to adjust the settings manually. Remote Control Functionality...
Seite 43
MADRIX PLEXUS User Manual (English) Important Information When using Direct Remote Control, please be aware of other settings of the PLEXUS device. Please pay special attention to the menu 'Network' > 'Art-Net'. Art-Net -> DMX 1 and Art-Net -> DMX 2 specify if incoming Art-Net data is routed to the corresponding XLR port (DMX 1 or DMX 2).
1) Connect your PLEXUS as well as the remote device accessing the PLEXUS to a network (USB will not work). 2) Open a web browser and type in the IP address of your PLEXUS. The IP address can be found and changed in the PLEXUS menu 'Network' > 'IP Address'.
Seite 45
3) Click to search for your connected devices. Please note: Make sure to use one and the same network and check if the PLEXUS device settings and the operating system settings of the remote device are correct. Your device will not appear in the PLEXUS Configuration dialog, as being connected to network, when the network settings are incorrect.
Seite 46
MADRIX 3 PLEXUS User Manual / Handbuch Interactive Remote Control The interactive demonstration in your web browser will look like this: Use your mouse (trackball, touchscreen, or any other input device) to click on the buttons , 'OK', and 'EDIT' for navigation and editing.
You can use MADRIX for the PLEXUS Live Mode, to create PLEXUS Configurations and Stand-Alone Shows, or to configure your device further. 'MADRIX Help And Manual' is the user guide for MADRIX. The MADRIX PLEXUS User Manual includes important features from this software manual. Nevertheless, often you can find more information on the software in the MADRIX Help And Manual.
Please note: Enabled USB drivers are required for Live Mode via USB and the USB connection from your PC to the device. Please make sure to activate the driver for the USB connection in the MADRIX Options. To access the Options of MADRIX, first go to the menu 'Preferences' -> 'Options...' (or 'Ctrl+Alt+O').
The PLEXUS device can be used as a live controller (Live Mode) or stand-alone interface (Stand- Alone Mode). In Live Mode, the PLEXUS allows you to send (or receive) data via MADRIX using up to 1024 DMX channels per device. You can either use 2x DMX-OUT, or 2x DMX-IN, or 1x DMX-OUT and 1x DMX- IN, or Art-Net in Live Mode.
MADRIX PLEXUS User Manual (English) 1.3.2.1 DMX-OUT (Output) Overview The PLEXUS allows you to send data via MADRIX using 1024 DMX channels per device. The MADRIX PLEXUS features two 5-pin, female XLR connectors. Please use XLR adapters if necessary! Usage This chapter describes how DMX512 can be used to connect your MADRIX PC to the MADRIX PLEXUS via USB to output DMX data.
Click this button if your device is not shown in the list in order to search for connected devices. Two list entries will be created for your PLEXUS device, one entry for every DMX port ('DMX 1' and 'DMX 2').
Seite 53
By default, 'Enable' as well as 'Output' should be enabled for every DMX port. Please check if both options, 'Enable' and 'Output', are activated! Your PLEXUS device is now configured to output DMX data. Setting Up The DMX Universe In the next step, set up the DMX 'Universe' for each DMX port. Simply use the two arrow buttons to adjust the values.
Seite 54
Sending full frames means that always the full 512 DMX channels of a DMX universe will be sent with every frame (even when you are using less than 512 channels per universe). Otherwise, MADRIX will send the number of DMX channels that is configured.
Seite 55
It considerably speeds up the procedure of programming the selected DMX512/Art-Net interfaces. In addition, the display of selected PLEXUS devices will flash regularly. Open the 'DMX Watcher' to monitor your DMX output or input. 'Watch Universe' will appear when you have selected a list entry. The DMX Watcher will open with the particular DMX Universe already entered.
Seite 56
MADRIX 3 PLEXUS User Manual / Handbuch Monitoring DMX Output Or DMX Input You can monitor incoming or outgoing DMX values on your device in the PLEXUS menus 'Tools' > 'Monitor DMX 1' and 'Tools' > 'Monitor DMX 2'. Important Notes Please make sure to save your MADRIX Setup after the configuration process.
This chapter describes how DMX-IN can be used to control the MADRIX software remotely. (An XLR port is be used for the connection.) If you want to learn more about directly controlling the MADRIX PLEXUS remotely, please see the chapter Remote Control.
Connecting MADRIX PLEXUS To Your PC Now, please connect the MADRIX directly to a free USB 2.0 port of your computer or use the USB power supply (or USB 2.0) and the network connection for Art-Net. If the MADRIX PLEXUS driver has been installed properly, the status LEDs will light up accordingly, as described in the chapter Troubleshooting.
Seite 60
Choose 'User' if you wish to create your individual remote configuration. For more information and the configurations of the 3 standard protocols, please see the MADRIX Help And Manual. You may also choose a protocol and click 'Edit...' to see the configurations.
MADRIX PLEXUS User Manual (English) Close the window with 'OK'. Monitoring DMX Output Or DMX Input You can monitor incoming or outgoing DMX values on your device in the PLEXUS menus 'Tools' > 'Monitor DMX 1' and 'Tools' > 'Monitor DMX 2'. Important Notes Please make sure to save your MADRIX Setup after the configuration process.
Usage This chapter describes how Art-Net can be used to connect your PC that runs the MADRIX software to the MADRIX PLEXUS via network cables to output DMX data. DMX data is then sent to the device over Ethernet/network. (Your LED fixtures, LED controllers, or LED drivers would be connected to the XLR ports of the PLEXUS device.)
255.0.0.0 It is recommended to use this address area. Please note: Recently, the 2.X network range has been made public. That is why MADRIX PLEXUS will have an IP address in the 10.X address range when shipped. Settings Of The Device...
Seite 64
In this menu, the current settings regarding Art-Net, a network protocol for DMX-over-Ethernet, are shown. More specifically, this menu contains the universe settings. Technically speaking Art- Net universes range from 0 to 255, but they are displayed on the PLEXUS and in MADRIX from 1 to 256.
MADRIX PLEXUS User Manual (English) You may change the settings in this menu, on the device (How To Edit Values). You can also configure the settings in the PLEXUS Configuration window in MADRIX. For more information, see Managing Devices Further.
Activate 'Enable' in the upper right corner. The checkbox will light up green, when activated. Click this button to let MADRIX automatically find your device. Your device will be shown in the list. (The entry 'ArtNet Remote' will be created automatically when activating Art-Net and can be ignored at this stage.)
Seite 67
In MADRIX, navigate to 'Preferences' > 'Device Manager...' (or press 'F4'). Open the first tab 'DMX Devices'. This window shows your connected devices. Two list entries will be created for your PLEXUS device and Art-Net, one entry for each DMX port. At this stage, both ports are deactivated.
Seite 68
MADRIX 3 PLEXUS User Manual / Handbuch Setting Up The DMX Universe In the next step, set up the DMX 'Universe' for each DMX port. Simply use the two arrow buttons to adjust the values. Click 'Apply' afterwards. Make sure that this configuration match the settings of your virtual LED matrix in the Patch.
Seite 69
MADRIX PLEXUS User Manual (English) Further Configuration You can also define the 'Frame Time' in ms for each device. Setting up the frame time can help in different cases. For example, certain LED fixtures might work best with a specific frame rate. Make sure to use the optimal frame rate for your fixtures. Some LED fixtures might have problems with high frame rates.
Seite 70
It considerably speeds up the procedure of programming the selected DMX512/Art-Net interfaces. In addition, the display of selected PLEXUS devices will flash regularly. Switches off all built-in status indicators of a device over Art-Net. MADRIX PLEXUS supports this feature.
Seite 71
Monitoring DMX Output Or DMX Input You can monitor incoming or outgoing DMX values on your device in the PLEXUS menus 'Tools' > 'Monitor DMX 1' and 'Tools' > 'Monitor DMX 2'. Important Notes Please make sure to save your MADRIX Setup after the configuration process.
MADRIX PLEXUS User Manual (English) Sync Mode An automatic sync mode for Art-Net devices is implemented in MADRIX. In this way you can activate or deactivate the usage of sync packages. This Sync Mode is not conform to Art-Net. To work properly it needs to be implemented by the manufacturer.
Seite 74
MADRIX 3 PLEXUS User Manual / Handbuch In MADRIX, navigate to the menu 'Preferences' > 'Device Manager...' > 'Art-Net'. Click 'Sync...' and a new dialog will open. First, select the correct network in the list. Second, activate 'Enable'. Third, choose if you want to activate sync packages to be sent before data is sent ('Pre-Sync').
Stand-Alone Mode of the MADRIX PLEXUS can be used to control LED installations without the need for a computer during the show. The PLEXUS can use an SD card (SD or SDHC) on which a Stand-Alone Show can be saved. But first, it is necessary to create such a Stand-Alone Show.
Seite 76
Convert the Record file (*.mrec) into a DMX Data file (*.dxd). (In MADRIX, use the Recording window for this task.) Step 6) Create a PLEXUS Configuration. This will be your Stand-Alone Show! (In MADRIX, use the PLEXUS Configuration window for this task.) Step 7) Upload your Stand-Alone Show onto the SD card.
Please read the chapter 'Using The Software' > 'Effects' in the MADRIX Help And Manual for Step Step 3) Please read the chapter 'Cue List' in the MADRIX Help And Manual if you wish to do Step 3). Continue with Step 4)
Seite 79
Delete any input to show all files. Managing Files And List Entries Shows MADRIX Record files (*.mrec) in the list that could be found in the specified directory. When activated, the button is green. Disable the option to hide all Record files.
Seite 80
Shows the length of the record, i.e. how long it is. The format is HH: MM:SS:FF (Hours:Minutes:Seconds:Frames). 'KF' Stands for Key Frames. MADRIX will automatically optimize the file size of records if recorded frames are identical. Hence, the total number of frames can be different to the number of recorded key frames. For example, a color change (without a fade) might use only two colors.
MADRIX PLEXUS User Manual (English) Window Size In order to increase the size of the Recording dialog window, please drag the border of the window until the best size is reached. In this way you can see more files in the list.
Seite 82
For the MADRIX PLEXUS a maximum frame rate of 40 FPS is recommended. Otherwise, PLEXUS devices may drop single frames to maintain the timing. PLEXUS devices are likely to drop frames in order to maintain the timing, when all 512 DMX channels of a DMX universe are used. If your DMX universes contain less than 512 channels (324 DMX channels, for example) this behavior is less likely.
Seite 83
Please make sure to configure all available options before recording (see above). Step 1) Begin recording by clicking on 'Start'. MADRIX will start to record the Main Output. Please note: When recording without a Cue List, you can change Storage Places, use the crossfader, use the Master, etc.
Seite 84
MADRIX 3 PLEXUS User Manual / Handbuch Step 3) Simply click 'Stop' to end the process. Please wait a few seconds to let MADRIX process the data. Afterwards you will need to enter a name for the new record. Step 4) Afterwards, you will see your record in the list.
Seite 85
A small preview window is provided in the lower left to inspect the record. Please note: If you see the message !NO MADRIX KEY!, that means that you are using MADRIX in demo mode. However, this is no problem. Your record will NOT include this text!
Seite 86
MADRIX 3 PLEXUS User Manual / Handbuch Use the provided controls to edit your record. That means you can preview, trim, and loop your record. First, select a list entry. Trim the record by setting up a new In Frame and a new Out Frame.
Seite 87
MADRIX PLEXUS User Manual (English) MADRIX will search the Record file in order to find a segment that is loopable. It will automatically set the In Frame and Out Frame afterwards. Use the button 'Export' to export your loop. Before that, you can also insert 'Blend Frames'.
Call up the Recording window again. In MADRIX, please go to the menu 'Window' -> 'Recording...' (or 'Ctrl+Alt+R'). First, select your MADRIX Record file (*.mrec) in the list. Please only select one file from the list! Second, switch to the tab 'PLEXUS Conversion'.
Seite 89
Please make sure that your virtual LED matrix (Patch) is configured correctly before generating DMX Data files (*.dxd). Note: The PLEXUS Conversion tab only factors in the settings of the Patch and not the settings of the Device Manager in MADRIX.
Seite 90
Please note: If your are using more than 2 DMX universes and more than 1 MADRIX PLEXUS at the same time, please make sure to have a list entry for each PLEXUS (You will need 1 list item for each PLEXUS of your installation).
Seite 91
1 should play DMX universe 1 and 2, PLEXUS number 2 should play DMX universe 3 and 4, PLEXUS number 3 should play DMX universe 5 and 6. Then, we need to create 3 list items or use the 'Auto' button.
Seite 92
Generate DMX Data files (*.dxd) for every single effect (each of your recordings). You may create several, different DMX Data files (*.dxd) from one MADRIX Record file (*.mrec). Your MADRIX Record file (*.mrec) will not be deleted when a new DMX Data files (*.dxd) is generated.
Step 6) Creating PLEXUS Configurations (Show Files) Overview To call up the PLEXUS Configuration window, in MADRIX, please go to the menu 'Tools' -> 'PLEXUS Configuration...' (or 'Ctrl+Alt+P'). It is highly recommended to maximize the size of the PLEXUS Configuration window.
Seite 95
MADRIX PLEXUS User Manual (English) The lower section of the PLEXUS Configuration window has two parts. The left part is used to manage your PLEXUS Configurations (create a new Configuration, import/export a Configuration, etc). The right part is used to edit each PLEXUS Configuration individually (add scenes, add events etc).
Seite 96
Configurations. This setting specifies what to do when a new Stand-Alone Show is uploaded to a MADRIX PLEXUS or when a newly recorded SD card is inserted into a MADRIX PLEXUS. Select 'No' and nothing will be played automatically. Select 'Last Scene' and the PLEXUS will continue with the last playes Scene where it last stopped.
Seite 97
Playback is delayed to ensure that all Slave devices are ready in the network after startup. How To Edit PLEXUS Configurations In order to edit your PLEXUS Configurations individually, use the lower right part of the PLEXUS Configuration window. First, create a new PLEXUS Configuration as described above.
Seite 98
Scenes are based on a DMX Data files (*.dxd). Scenes are smaller parts of a whole show. All Scenes together create your Stand-Alone Show. First, please select one PLEXUS Configuration you wish to edit. Creates a new Scene. When creating a new Scene, a new window will open and you will be asked to select a DMX Data file (*.dxd).
Seite 99
MADRIX PLEXUS User Manual (English) Removes a Scene. Select the particular Scene first. Duplicates a Scene. Select the particular Scene first. Enter a new name for the copied Scene in the second step. In addition, please edit the following columns according to your requirements.
Seite 100
First, enter a number of frames. MADRIX will add these frames to the end of the Scene and therefore loops towards the first frame of your Scene. A cross-fade is created. For example, if your record was set to a frame rate of 33 FPS and you enter 66 here, two seconds will be used for a loop towards the first frame.
Seite 101
Removes a Timer. Select the particular Timer first. Duplicates a Timer. Select the particular list item first. A maximum of 1000 Timers can be configured per PLEXUS Configuration to ensure performance. In addition, please edit the following columns according to your requirements.
Seite 102
MADRIX 3 PLEXUS User Manual / Handbuch 'Action' defines the type of Timer. Applicable values are: 'Scene', 'Intensity', 'Speed, 'Next, 'Previous', 'Stop', 'Play', 'Pause', 'Port 1', 'Port 2', 'Port 3', 'Port 4', 'Port 5', 'Port 6', 'Port 7', 'Port 8', 'Port 9', 'Port 10'. 'Scene' will trigger a specific Scene to be played.
Seite 103
Extension Ports: The tab 'Extension Ports' allows you to configure the individual pins of the extension port. First, please select one PLEXUS Configuration you wish to edit. Restores all settings of the currently selected Ports to their default values. This will discard any changes you have made.
Seite 104
DMX Data Files: The tab 'DMX Data Files' shows all DMX Data iles (*.dxd) that are used in the selected PLEXUS Configuration. It represents a database of your DMX Data files within one PLEXUS Configuration.
Seite 105
Removes an existing DMX Data file from the PLEXUS Configuration. shows the indexing number of the Data File. This value cannot be changed. 'In Use' shows how often the Data File is used in your PLEXUS Configuration by Scenes. This value cannot be changed. 'File' shows the exact name of the record file.
Your PLEXUS must be connected via USB or via Ethernet (network). First, select your MADRIX PLEXUS. Second, select your PLEXUS Configuration. Third, click 'Upload' and the PLEXUS Show will be saved on the SD card of your device. Step 8) Activating Stand-Alone Mode Last but not least, you will have to activate Stand-Alone Mode on your MADRIX PLEXUS.
This topic includes tips regarding the PLEXUS Configuration window and working with PLEXUS Configurations and Stand-Alone Shows. You can create a Stand-Alone Show without having connected the PLEXUS to the computer. In order to upload a Stand-Alone Show onto an SD card, either the SD card or the device with the SD card must be connected.
Overview Certain settings of your device can be managed using the PLEXUS Configuration window. To call up the PLEXUS Configuration window, please go to the menu 'Tools' > 'PLEXUS Configuration ' (or 'Ctrl+Alt+P'). It is highly recommended to maximize the size of the PLEXUS Configuration window.
Seite 110
Buttons Scans the USB ports of your computer and the network (Ethernet) for connected PLEXUS devices. If devices are found, they will be shown in the list. This symbol shows that the device is connected via USB. This symbol shows that the device is connected via network (Ethernet).
Seite 111
(as described in the table below). Synchronizes the internal clock of the PLEXUS with the clock of your computer. The computer clock will define the time and date that is used. First, select your PLEXUS devices in the list. Then, click 'Sync Clock.
Seite 112
MADRIX 3 PLEXUS User Manual / Handbuch 'IP Address / defines the network settings regarding IP address, Subnet mask, and Subnet Mask' standard gateway for the device. On the device, use the menu 'Network' > 'IP Address'. 'Intensity' defines the main brightness of the output your device in percent. Applicable values are: 0 - 100%.
Seite 113
MADRIX PLEXUS User Manual (English) 'SD Card' cannot be edited. The 'used space'/'total available space' of your SD card is shown. The values are displayed in GB. 'Remote Control' defines the source for remote control. You can choose to receive remote commands via USB, via Art-Net, or to turn remote control off (Disabled).
Seite 114
MADRIX 3 PLEXUS User Manual / Handbuch 'Art-Net -> DMX defines which Art-Net universe is assigned to the first XLR port for output (DMX 1). On the device, use the menu 'Network' > 'Art-Net'. More information is provided in the chapter Art-Net (Output).
Seite 115
'0°' (no rotation) and '180°' (rotated display). On the device, use the menu 'Settings' > 'Device'. 'Language' defines the language of the PLEXUS menus. Choose from 'English', 'Deutsch' (German), or Español (Spanish). On the device, use the menu 'Settings' > 'Device'.
Seite 116
MADRIX 3 PLEXUS User Manual / Handbuch 'Full Frames defines if the device should always send full frames for the second XLR DMX 2' output. On the device, use the menu 'Settings' > 'DMX'. More information is provided in the chapter LCD Graphics Display (PLEXUS Menus).
Please note that the synchronization works only when all corresponding devices are connected and set up in one and the same network (Ethernet). This includes physical connection (cabling) as well as settings in MADRIX, the PLEXUS devices, and network settings of the operating system.
Seite 118
MADRIX 3 PLEXUS User Manual / Handbuch To call up the PLEXUS Configuration window, please go to the menu 'Tools' > 'PLEXUS Configuration ' (or 'Ctrl+Alt+P'). Select your device in the list. Change the settings for every required device, one at a time.
Seite 119
MADRIX PLEXUS User Manual (English) 'Off' will deactivate any synchronization for the device. 'Master' will set the interface to work as central clock and the main interface in the group (Master interface). 'Slave' will set the interface as Slave interface to synchronize with the 'Master'.
Seite 120
Please continue with the next chapter Group. Group Call up the PLEXUS Configuration window again. Go to the menu 'Tools' > 'PLEXUS Configuration ' (or 'Ctrl+Alt+P'). Select your device in the list. Change the settings for every required device, each at a time.
Seite 121
MADRIX PLEXUS User Manual (English) PLEXUS Device Settings Sync Instead of using the PLEXUS Configuartion window, you may check the settings on the device itself. Navigate to the PLEXUS menu 'Network' > 'Sync'. This menu shows the current settings regarding Master-Slave Synchronization of your current PLEXUS Configuration.
In the future, there could be an update of the software program, a further developed firmware. If there is a new firmware version for the MADRIX PLEXUS, those firmware updates will most likely be implemented directly into the MADRIX software. Hence, there is a chance that a new MADRIX version will include an update for the PLEXUS as well.
Seite 124
Fixed that SD card formatting could fail after a Factory Default Reset. Fixed that Speed could not be set up correctly when using the PLEXUS Configuration Fenster and the USB connection. Improved GUI refreshing of the display for intense processing tasks, such as uploading and downloading.
Seite 125
Changed Art-Net universes to be displayed from 1 to 256, instead from 0 to 255. A multitude of settings can now additionally be set up in the PLEXUS Configuration Fenster in MADRIX, while they were only available on the device before.
Seite 126
Fixed an issue with the clock running out of sync after a while. Fixed an issue with synchronization regarding Master-Slave-Synchronization. The default IP address of a PLEXUS device will now be 10.x.x.x after a reset to factory defaults. Improved display message when the MADRIX PLEXUS is set to standby mode.
Seite 127
Released with: MADRIX 2.14b (2.14.2.1) - December 2012 Also valid for: MADRIX 3.0 (3.0.0.5) - July 2013 / MADRIX 3.0a (3.0.1.0) - September 2013 / MADRIX 3.1 (3.1.0.1) - November 2013 / MADRIX 3.1a (3.1.1.1) - January 2014 / MADRIX 3.2 (3.2.0.3) - March 2014...
Seite 128
Frames in Stand-Alone Mode. This can help with fixtures that require a frame to include all 512 channels. Changed the position and name of the PLEXUS menu Settings > Network to Network > IP Address. Long Configuration names and device names will now be scrolled under menu Information >...
Seite 129
MADRIX PLEXUS User Manual (English) Version 1.08.5780 Released with: MADRIX 3.5a (3.5.1.0) - December 2015 Requires PLEXUS driver 6.0.0518.2 Fixed an issue that could cause a unit to become unresponsive when setting a high speed (400%, for example) in the menu 'Stand-Alone' > 'Intensity/Speed' when playing back very large Scene files.
Seite 130
MADRIX 3 PLEXUS User Manual / Handbuch Version 1.09.6375 Released with: MADRIX 3.6c (3.6.3.0) - October 2016 Requires PLEXUS driver 6.0.0518.2 Devices now use the compilation date of the firmware and set the time to 12:34:00 after changing the battery or using the device for the first time instead of showing only zeros.
1) Please connect your PLEXUS to your PC using USB. 2) In MADRIX, go to the menu 'Tools' > 'PLEXUS Configuration' (or 'Ctrl+Alt+P'). 3) When the device is recognized by MADRIX already, a message may be shown saying that the firmware version is not up-to-date.
Seite 133
The manufacturer may update the hardware design of the device for new units. Please note the following: Hardware model V1.6 ('Model: PLEXUS V1.6') can be updated using firmware version 1.07.4369 or higher without any problems. Hardware model V1.7 ('Model: PLEXUS V1.7') requires at least firmware version 1.06.4260 or higher! Please do not use a previous version.
The MADRIX PLEXUS Updater is a tool for advanced users. It should not be used without reason! This tool should mainly be used, when it is impossible for you to start the MADRIX software for any reason. The MADRIX PLEXUS Updater can be used for several, specific tasks.
Seite 135
'Reset To Factory Default Resets all settings of all PLEXUS devices that are connected to Settings' the computer via USB to the standard values. Use this function to restore the original, functioning state of the device.
Seite 136
MADRIX 3 PLEXUS User Manual / Handbuch Important Note If new drivers and a new firmware are available for the MADRIX PLEXUS, please always update the firmware first and then the drivers! MADRIX PLEXUS Updater does not work when MADRIX is running. Please close MADRIX and restart MADRIX PLEXUS Updater.
Yes. Multiple devices can be used together to control larger LED projects. Can I upgrade the PLEXUS software license? No. One PLEXUS includes a software license for 1024 DMX channels. But you may simply connect more units to access more channels.
Seite 138
Why are recorded Effects called Scenes and not Effects? A Scene for the PLEXUS is created by recording the Main Output of MADRIX. That means you can use MADRIX as usual, for example by using the cross-fader, Master Fader, Speedmaster, Color Filter or by switching effects, etc.
MADRIX PLEXUS User Manual (English) Help And Troubleshooting Description Of Status LED Codes The following tables describe the status codes of the three status LEDs. USB/Power COLOR STATUS LED USB/POWER USB/Power not connected. P o we r e d o ff The device has no power.
Seite 141
Please go to the PLEXUS menu 'Settings' > 'Device'. Set 'Ports' to 'Enabled'. The PLEXUS shows up in the Windows Device Manager. But MADRIX is not able to find the device! 1) Please check if USB drivers are enabled in MADRIX in the MADRIX Options. 2) Please update the drivers of the device as described above.
PLEXUS Configuration window. My LEDs do not show the lighting effects correctly! Please go to the PLEXUS menu 'Settings' > 'DMX'. Set 'DMX 1', 'DMX 2', 'Art-Net 1', 'Art-Net 2' to 'On' and test again. Standby Mode The MADRIX PLEXUS may display 'STANDBY'.
MADRIX PLEXUS User Manual (English) Hard Reset Important Information The following instructions is to be seen with great caution! It is only included for your information until you might need it. Perform a hard reset only when really needed! There are two button combinations in order to perform hard resets.
Seite 144
You may reboot your device using the integrated bootloader to reinstall the PLEXUS firmware. This might be useful if the LCD graphics display (the PLEXUS menus) have stopped working and if you cannot select a different menu anymore, for example.
E-mail: info@madrix.com Copyright MADRIX is a registered trademark of inoage GmbH. All other company names and/or product names are trademarks and/or entered trademarks of their respective holders. The product might not always be conforming to the presentation, features, and performances. Technical data can differ slightly, depending on the operating system and the chosen hardware.
Seite 146
MADRIX 3 PLEXUS User Manual / Handbuch Under no circumstances does inoage GmbH take on the responsibility for liabilities for faults for losses in sales volume or profits, that occur through the usage of the product, through the serviceability, through abuse, happenings, circumstances or actions, that we have no influence on.
Einführung Das MADRIX PLEXUS ist ein USB 2.0/DMX512-Steuerungsgerät (Interface). Das MADRIX PLEXUS steuert bis zu 2 Universen über DMX512 oder Art-Net als vielseitiges Standalone-Gerät oder Live-Gerät. Es ist das erste Interface mit Unterstützung für Standalone- Wiedergabe von MADRIX-Lichtshows und -Effekten.
MADRIX 3 PLEXUS User Manual / Handbuch MADRIX PLEXUS (Gerät) Das Gerät ist als Steuerungsgerät konzipiert und wird als Interface an verschiedene, steuerbare Leuchtprodukte/Controller mit Hilfe von DMX512 (USB-zu-DMX512) bzw. Art-Net (DMX-über-Netzwerk) angeschlossen. Verwenden Sie das Gerät nur zu seinem vorgesehenen Zweck.
MADRIX PLEXUS Handbuch (Deutsch) LCD-Grafikdisplay (Menüstruktur) 2.2.1 Übersicht Dieses Kapitel beschreibt die zahlreichen Menüs des PLEXUS und gibt weitere Informationen zum LCD-Grafikdisplay. Symbole Eine SD-Karte ist in das Gerät eingesteckt. Es befindet sich keine SD-Karte im Gerät. Die Werte in diesem Menü können bearbeitet werden.
MADRIX 3 PLEXUS User Manual / Handbuch Gebrauchsanweisung Wie geht die Menü-Auswahl? Drücken Sie "OK", um das Menü zu öffnen. Nutzen Sie dann die Pfeiltasten zur Navigation. Wenn der gewünschte Menüpunkt ausgewählt ist, drücken sie "OK", um ihn zu aktivieren.
IP-Adresse werden angezeigt. Konfiguration Öffnen Sie das Menü "Informationen" > "Konfiguration". Das Menü enthält Details über die PLEXUS-Konfiguration (die Show) und dazugehörige Einstellungen, welche sich auf der SD-Karte befindet. Hilfe Öffnen Sie das Menü "Informationen" > "Hilfe".
Seite 156
Zeitgeber (Timers) werden in der PLEXUS-Konfiguration in MADRIX erstellt. Ports Öffnen Sie das Menü "Standalone" > "Ports". Alle Ports der aktuellen PLEXUS-Konfiguration werden daraufhin in einer Liste dargestellt. Wählen Sie einen bestimmten Port mit Hilfe der Tasten und . Der Typ, seine Funktion ("Aktion") und weitere Details werden ersichtlich.
Seite 157
MADRIX PLEXUS Handbuch (Deutsch) Ports werden in der PLEXUS-Konfiguration in MADRIX konfiguriert. Helligkeit/Tempo Öffnen Sie das Menü "Standalone" > "Helligkeit/Tempo". Helligkeit und Tempo der Wiedergabe können direkt in diesem Menü beeinflusst werden. Drücken Sie zur Verdunkelung. Drücken Sie zur Erhöhung der Helligkeit.
Dieses Menü beinhaltet die Einstellungen bezüglich Art-Net, einem Standardprotokoll zur Übertragung von DMX-Daten über Netzwerk. Art- Net-Universen reichen technisch von 0 bis 255, werden aber in MADRIX und auf dem PLEXUS von 1 bis 256 angezeigt. "Art-Net -> DMX 1" zeigt an, welches Art-Net-Universum dem ersten XLR-Anschluss zur Ausgabe zugewiesen ist (DMX 1).
Seite 159
Art-Net-Universum angegeben, an welches die Daten gesendet werden sollen. Damit ist Art-Net im Standalone-Modus möglich. Das bedeutet, dass das PLEXUS eine Standalone-Show abspielt und die Daten per Art- Net über das Netzwerk direkt an die LED-Produkte gesendet oder vorher widerrum in DMX-Signale gewandelt werden können. Die Daten werden über Art-Net an das eingestellte Art-Net-Universum im Broadcast-Modus...
Seite 160
MADRIX 3 PLEXUS User Manual / Handbuch Die Einstellungen können ebenso im Fenster "PLEXUS Configuration" in MADRIX angepasst werden. Weitere Informationen finden Sie im Kapitel Weitere Konfigurationsmöglichkeiten. Weitere Informationen über Art-Net erhalten Sie im Kapitel Art-Net (Ausgabe). Synchronisation Öffnen Sie das Menü "Netzwerk" > "Synchronisation".
MADRIX PLEXUS Handbuch (Deutsch) Das Werkzeuge-Menü Das Menü "Werkzeuge" enthält vier Einträge. Anzeige DMX 1 Öffnen Sie das Menü "Werkzeuge" > "Anzeige DMX 1". Dieses Menü stellt die Ein- bzw. Ausgabe von DMX-Daten des ersten XLR-Anschlusses grafisch zur Überprüfung dar (DMX 1).
Seite 162
MADRIX 3 PLEXUS User Manual / Handbuch Nutzen Sie , um im Modus Tabelle zu scrollen. Nutzen Sie , um den DMX-Kanal in den Modi Grafik und Kanal zu wechseln. Im Modus Grafik wird der einzelne Kanal oben rechts zusätzlich zur Grafik angezeigt.
Seite 164
Die Einstellungen können direkt in diesem Menü geändert werden (Wie bearbeitet man Werte?). Die Einstellungen können ebenso im Fenster "PLEXUS Configuration" in MADRIX angepasst werden. Weitere Informationen finden Sie im Kapitel Weitere Konfigurationsmöglichkeiten. Weitere Information zum Thema finden Sie im Kapitel Fernsteuerung.
Konfigurationsmöglichkeiten. Öffnen Sie das Menü "Einstellungen" > "DMX". In diesem Menü kann eingestellt werden, ob MADRIX PLEXUS immer alle Kanäle für die DMX-Ausgabe ("DMX 1" und "DMX 2") sowie Art-Net (DMX-Universen für "Art-Net 1" und "Art-Net 2") sendet ("An") oder optimierte Einzelbilder ("Aus").
Seite 167
MADRIX PLEXUS Handbuch (Deutsch) Die Einstellungen können direkt in diesem Menü geändert werden (Wie bearbeitet man Werte?). Standort Öffnen Sie das Menü "Einstellungen" > "Standort". Einstellungen zur geographischen Position des Gerätes finden sich in diesem Menü. Nutzen Sie , um die Werte zu ändern.
Während der Standalone-Wiedergabe kann über die Bedientasten gesteuert werden. Weitere Informationen finden Sie im Kapitel LCD-Grafikdisplay (Menüstruktur). Öffnen Sie dazu das PLEXUS-Menü "Standalone" > "Wiedergabe". Eine Szene vor springen. Eine Szene zurück gehen. Wiedergabe pausieren. Ein zweites Mal betätigen, um die Wiedergabe fortzusetzen.
MADRIX PLEXUS Handbuch (Deutsch) Tastenbelegung Je nach Wunsch kann die Option "Rotiere um 180°" im PLEXUS-Menü "Einstellungen" > "Gerät" eingeschalten werden. Dabei wird die Anzeige auf dem Display um 180° gedreht. Analog dazu wird die Belegung der Bedientasten ebenso verändert und gedreht und somit rotierten Anzeige angepasst.
MADRIX 3 PLEXUS User Manual / Handbuch SD-Karten 2.2.4 Überblick Der integrierte SD-Kartensteckplatz befindet sich oben am Gerät. Zugang erhält man durch die angebrachte Metallklappe. Unterstützt werden sowohl SD-Karten (max. 2 GB) als auch SDHC- Karten (max. 32 GB). SDHC-Karten werden empfohlen.
Seite 173
MADRIX PLEXUS Handbuch (Deutsch) Dateisystem Sollten Sie eine SD-Karte zur Benutzung mit dem MADRIX PLEXUS vorbereiten wollen oder ein SD- Karte komplett bereinigen wollen, so können Sie den Datenträger in Windows formatieren. Hinweis: Beim Formatieren werden alle Daten auf der SD-Karte gelöscht! FAT16 oder FAT32 muss als Dateisystem beim Formatieren Ihrer SD-Karte ausgewählt...
Fernsteuerung angeschlossen werden. Spezifikationen: 15-polig, D-Sub, US, weiblich Rufen Sie in MADRIX im Menü "Tools" > "PLEXUS Configuration… " > "Extension Ports" auf, um die 10 Ports für die jeweilige PLEXUS-Konfiguration individuell zu konfigurieren. Weitere Informationen finden Sie im Kapitel 6.
Verschiedene Geräte können an diese Ports angeschlossen werden. Ein Port kann entweder als Empfangseinheit funktionieren und somit Signale von externen Geräte empfangen. Gemäß der PLEXUS-Konfiguration kann dann ein Signal eine bestimmte Aktion hervorrufen (z.B. Stop). Oder ein Port kann Signale nach außen an externe Geräte senden, welche dieses Signal wiederum verarbeiten können.
Direkte Fernsteuerung des Gerätes über DMX oder Art-Net Überblick Sie können DMX- bzw. Art-Net-Daten direkt an das MADRIX PLEXUS senden. Auf diese Weise können Sie bestimmte Befehle verwenden (siehe unten), um das Gerät fernzusteuern. Das PLEXUS wird auf die eingehenden DMX- oder Art-Net-Signale reagieren und daraufhin bestimmte Funktionen ausführen.
Seite 183
Art-Net weitergesendet werden sollen. Die Einstellungen können direkt in diesem Menü geändert werden (Wie bearbeitet man Werte?). Die Einstellungen können ebenso im Fenster "PLEXUS Configuration" in MADRIX angepasst werden. Weitere Informationen finden Sie im Kapitel Weitere Konfigurationsmöglichkeiten. Liste aller Befehle Die folgende Liste enthält alle verfügbaren Befehle für die Fernsteuerung und beschreibt ihre...
Seite 184
MADRIX 3 PLEXUS User Manual / Handbuch Die folgenden DMX-Kanäle basieren auf dem Standartwert des "Startkanals" von 1. Wenn Sie einen anderen Startkanal verwenden möchten, ändert sich der jeweilige DMX-Kanal entsprechend. Funktion Nutzba Nutzba DMX- Beschreibung r im r im...
Seite 185
< 128 Helligkeitsgru 0 - 255 definiert eine Maske. Beim Erstellen von DXD- ppe 1 Dateien in MADRIX wird automatisch der Farbkanal Rot zugewiesen. Der Standardwert ist 255/100% (volle Helligkeit). Helligkeitsgru 0 - 255 definiert eine Maske. Beim Erstellen von DXD-...
Seite 186
Helligkeitsgruppen Acht Helligkeitsgruppen sind in der obenstehenden Tabelle aufgeführt. Vier können mit Hilfe von MADRIX aktiv genutzt werden. Dies ist eine Funktion, die hauptsächlich im Zusammenhang mit der Fernsteuerung nutzbar ist. Eine Helligkeitsgruppe beinhaltet alle Farbwerte (0 bis 255) einer einzelnen Farbe. Helligkeitsgruppe 1 regelt den Farbkanal Rot.
MADRIX PLEXUS Handbuch (Deutsch) Anzeige Fernst. Öffnen Sie das Menü "Fernsteuerung" > "Anzeige Fernst.". Dieses Menü stellt für die Fernsteuerung die eingehenden DMX-Daten grafisch zur Überprüfung dar (DMX 1 oder DMX 2). Alle 20 Kanäle können überprüft werden mit Hilfe von hexadezimalen Werten.
Seite 188
MADRIX 3 PLEXUS User Manual / Handbuch Helligkeit, Tempo "Standalone" > "Helligkeit/Tempo" Helligkeitsgruppe 1 - 8 Einfrieren "Werkzeuge" > "Einfrieren" Wichtige Informationen Bei der Nutzung der Fernsteuerung sollten andere Einstellungen des Gerätes unbedingt beachtet werden. Bitte achten Sie insbesondere auf die Einstellungen im Menü "Netzwerk" > "Art-Net".
1. Das PLEXUS und das Gerät zur Fernsteuerung müssen zunächst an ein Netzwerk angeschlossen werden (der Anschluss nur über USB funktioniert in diesem Fall nicht). 2. Öffnen Sie danach einen Browser und tragen Sie die IP-Adresse des PLEXUS ein. Sie kann im PLEXUS-Menü "Netzwerk" > "IP-Adresse" abgefragt und geändert werden.
Seite 190
Betriebssystems des Gerätes zur Fernsteuerung stimmen bzw. korrekt konfiguriert wurden. PLEXUS Configuration-Fenster 1. Das PLEXUS und das Gerät zur Fernsteuerung müssen zunächst an ein Netzwerk angeschlossen werden (der Anschluss nur über USB funktioniert in diesem Fall nicht). 2. Navigieren Sie in MADRIX zu dem Menü "Tools" > "PLEXUS Configuration" (oder "Strg+Alt+P"...
MADRIX PLEXUS Handbuch (Deutsch) Interaktive Fernsteuerung Die interaktive Darstellung in Ihrem Web-Browser ist im Folgenden dargestellt: Nutzen Sie Ihre Computermaus (Trackball, Touchscreen, oder andere Eingabegeräte), um die Knöpfe , "OK", and "EDIT" anzuklicken. Sie werden wie gehabt zur Navigation und Bearbeitung verwendet.
MADRIX ist eine professionelle Software zur Steuerung von LEDs. Das PLEXUS bringt die Softwarelizenz für 1024 DMX-Kanäle bereits mit. Die Datenausgabe (die Lizenz) wird aktiviert, sobald das Gerät an einen Computer mit installierter und gestarteter MADRIX-Software angeschlossen wird. Die USB- bzw. Netzwerktreiber müssen zudem in MADRIX aktiviert sein.
Hinweis: Aktivierte USB-Treiber sind zwingende Voraussetzung für den Live-Modus über USB und die Verbindung vom PC zum Gerät über USB. Öffnen Sie bitte das Menü "Preferences" > "Options… " in MADRIX. Wählen Sie den Reiter "Devices USB" aus. Aktivieren Sie "MADRIX PLEXUS".
Öffnen Sie bitte das Menü "Preferences" > "Options… " in MADRIX. Wählen Sie den Reiter "Devices Network" aus. Aktivieren Sie "'Enable LUNA / NEBULA / PLEXUS /STELLA" in dem Bereich "inoage – MADRIX" Bestätigen Sie mit "Apply". Schließen Sie das Fenster mit "OK".
2.3.2 Überblick Das MADRIX PLEXUS kann als Live-Interface oder als Standalone-Gerät eingesetzt werden. Im Live-Modus können bis 1024 DMX-Kanäle pro Gerät ausgegeben oder empfangen werden. Dabei stehen entweder 2x DMX-OUT, oder 2x DMX-IN, oder 1x DMX-OUT und 1x DMX-IN, oder Art-Net zur Verfügung.
DMX-Ausgabe (DMX-OUT) Übersicht Das PLEXUS ermöglicht es, mit Hilfe von MADRIX DMX-Daten zu senden. Hinweis: Das PLEXUS verfügt über zwei 5-polige, weibliche XLR-Stecker. Bitte nutzen Sie entsprechende Adapter, wenn nötig! Anwendung Dieses Kapitel beschreibt, wie DMX512 genutzt werden kann, um Ihren MADRIX-PC mit dem PLEXUS über USB zu verbinden und DMX-Daten auszugeben.
MADRIX PLEXUS Handbuch (Deutsch) Verbinden des MADRIX PLEXUS mit dem PC Schließen Sie nun das MADRIX an einen freien USB 2.0-Anschluss Ihres Computers an. Wenn die Installation der Software und des Treibers erfolgreich war, zeigt die Status-LED USB/Power dies an. Weitere Informationen finden Sie dazu im Kapitel Hilfe und Fehlerbehebung.
MADRIX 3 PLEXUS User Manual / Handbuch Standardmäßig sind "Enable" sowie "Output" für jeden DMX-Anschluss aktiviert. Stellen Sie bitte sicher, dass beide Optionen aktiviert sind! Ihr MADRIX PLEXUS ist nun zur DMX-Ausgabe vorbereitet. Einstellen des DMX-Universums Im nächsten Schritt muss das DMX-Universum ("Universe") für jeden DMX-Anschluss eingestellt werden.
MADRIX PLEXUS Handbuch (Deutsch) Weitere Konfiguration Zusätzlich kann die "Frame Time" ("Zeit der Einzelbilder") in ms für jedes Gerät eingegeben werden. Die FPS (Frames Per Second, Einzelbilder pro Sekunde) werden daraufhin automatisch angepasst. Die Einstellung ist für verschiedene Anwendungsfälle hilfreich. Zum einen könnte beispielsweise eine Einstellung für bestimmte LED-Produkte optimal sein.
Dieses Kapitel beschreibt, wie die DMX-Eingabe (DMX-IN) zur Fernsteuerung der Software MADRIX verwendet werden kann. (Ein XLR-Eingang wird für die Verbindung genutzt.) Wenn Sie mehr über die direkte Fernsteuerung des MADRIX PLEXUS erfahren möchten, finden Sie weitere Informationen im Kapitel Fernsteuerung. MADRIX Installieren Sie bitte zunächst die MADRIX-Software, falls noch nicht geschehen.
MADRIX PLEXUS Handbuch (Deutsch) Verbinden des MADRIX PLEXUS mit dem PC Schließen Sie nun das MADRIX an einen freien USB 2.0-Anschluss Ihres Computers an. Wenn die Installation der Software und des Treibers erfolgreich war, zeigt die Status-LED USB/Power dies an. Weitere Informationen finden Sie dazu im Kapitel Hilfe und Fehlerbehebung.
MADRIX 3 PLEXUS User Manual / Handbuch Schließen Sie das Fenster mit "OK". Anzeige von DMX-Daten Ein- und ausgehende DMX-Daten können in den PLEXUS-Menüs "Werkzeuge" > "Anzeige DMX 1" und "Werkzeuge" > "Anzeige DMX 2" überprüft werden. Wichtige Hinweise Bitte sichern Sie Ihre MADRIX Setup-Datei im Anschluss an die erfolgreiche Konfiguration.
Das Art-Net-Protokoll ist ein weit verbreiteter Standard zur Übertragung von DMX512 über Netzwerk (Ethernet). Anwendung Dieses Kapitel beschreibt, wie Art-Net genutzt werden kann, um Ihren MADRIX-PC mit dem PLEXUS über Netzwerk zu verbinden und DMX-Daten auszugeben. (Ihre LED-Leuchtkörper, LED-Controller, oder LED-Driver werden über die XLR-Ausgänge mit dem PLEXUS verbunden.)
MADRIX 3 PLEXUS User Manual / Handbuch Konfiguration der Netzwerkeinstellungen Stellen Sie sicher, dass die Netzwerkeinstellungen des Betriebssystems und des Gerätes korrekt sind! Nutzen Sie zur Konfiguration der Netzwerkeinstellungen das PLEXUS-Menü "Netzwerk" > "IP- Adresse". Oder nutzen Sie den PLEXUS Configuration-Fenster.
Dieses Menü beinhaltet die Einstellungen bezüglich Art-Net, einem Standardprotokoll zur Übertragung von DMX-Daten über Netzwerk. Art-Net-Universen reichen technisch von 0 bis 255, werden aber in MADRIX und auf dem PLEXUS von 1 bis 256 angezeigt. "Art-Net -> DMX 1" zeigt an, welches Art-Net-Universum dem ersten XLR-Anschluss zur Ausgabe zugewiesen ist (DMX 1).
Seite 210
Daten an das Art-Net-Netzwerk gesendet werden sollen. Es wird dementsprechend auch das Art-Net-Universum angegeben, an welches die Daten gesendet werden sollen. Damit ist Art-Net im Standalone-Modus möglich. Das bedeutet, dass das PLEXUS eine Standalone-Show abspielt und die Daten per Art-Net über das Netzwerk direkt an die LED- Produkte gesendet oder vorher widerrum in DMX-Signale gewandelt werden können.
MADRIX PLEXUS Handbuch (Deutsch) Konfiguration von Art-Net in MADRIX Navigieren Sie in MADRIX zu dem Menü "Preferences" > "Device Manager..." > Reiter "Art-Net" Aktivieren Sie "Enable" in der rechten, oberen Ecke. Das Auswahlkästchen leuchtet grün, wenn aktiviert. Klicken Sie diese Schaltfläche, damit MADRIX Ihr Gerät automatisch erkennt und findet.
Klicken Sie diese Schaltfläche, wenn Ihr verbundenes Gerät nicht in der Liste erscheint, um automatisch nach angeschlossenen Geräten zu suchen. Für das PLEXUS-Gerät werden bezüglich Art-Net zwei Einträge in der Liste erstellt, einen für jeden DMX-Anschluss. An dieser Stelle sind beide Einträge noch deaktiviert.
Seite 214
MADRIX 3 PLEXUS User Manual / Handbuch Einstellen des DMX-Universums Im nächsten Schritt muss das DMX-Universum ("Universe") für jeden DMX-Anschluss eingestellt werden. Nutzen Sie dazu die zwei Pfeilknöpfe oder tragen Sie per Tastatur einen Wert ein. Bestätigen Sie die Eingabe mit "Apply".
Seite 215
Identifikation komplett weiß auf. Dies hilft beim Einrichten der LED-Installation mittels MADRIX. Zusätzlich leuchtet das Grafikdisplay der ausgewählten Geräte regelmäßig auf. Schaltet alle Status-LEDs der Gerätes über Art-net aus. MADRIX PLEXUS unterstützt diese Funktion. Lässt alle Status-LEDs wieder normal arbeiten, nachdem sie zuvor ausgeschaltet wurden.
Seite 216
Rand des Fensters. Wählen Sie den Rand aus und ziehen Sie im Anschluss bei gedrückter, linker Maustaste den Rahmen nach unten. Anzeige von DMX-Daten Ein- und ausgehende DMX-Daten können in den PLEXUS-Menüs "Werkzeuge" > "Anzeige DMX 1" und "Werkzeuge" > "Anzeige DMX s2" überprüft werden. Wichtige Hinweise Bitte sichern Sie Ihre MADRIX Setup-Datei im Anschluss an die erfolgreiche Konfiguration.
Seite 217
MADRIX PLEXUS Handbuch (Deutsch) Weitere Konfiguration Es können weitere Einstellungen vorgenommen werden. Nutzen Sie dazu diese Schaltfläche im "Device Manager" im Reiter "Art-Net" oder im Device Manager im Reiter "DMX Devices". Dann öffnet sich das folgende Fenster "Art-Net Device Configuration".
Seite 218
Auf diese Weise kann man das Senden von Synchronisationspaketen anschalten (oder ausschalten). Dieser Synchronisations-Modus ist nicht Teil der Art-Net-Spezifikation und muss von Herstellern unterstützt werden. Für MADRIX PLEXUS ist diese Option empfohlen. Vor dem Einschalten des Sync-Modus sollte überprüft werden, ob alle aktivierten Art- Net-Geräte auch im Netzwerk zur Verfügung stehen.
MADRIX PLEXUS Handbuch (Deutsch) Navigieren Sie in MADRIX zu dem Menü "Preferences" > "Device Manager..." > "Art-Net". Aktivieren Sie "Sync...". Ein neues Fenster öffnet sich. Wählen Sie nun das korrekte Netzwerk in der Liste aus. Aktivieren Sie danach "Enable" und wählen Sie, ob Sync-Pakete vor den Art-Net- Datenpaketen ("Pre-Sync") oder nach den Art-Net-Datenpaketen ("Post-Sync") versendet...
Installation direkt. Im Gegensatz dazu erlaubt es der Standalone-Modus des MADRIX PLEXUS, LED- Installationen ohne einen PC während der Show anzusteuern. Das PLEXUS kann eine eingesteckte SD-Karte nutzen (SD oder SDHC), auf der eine Standalone- Show abgespeichert wird. Zunächst muss eine solche Standalone-Show jedoch erstellt werden.
Seite 221
Configuration-Fenster.) 7. Schritt Laden Sie Ihre Standalone-Show auf die SD-Karte hoch. (Nutzen Sie in MADRIX den PLEXUS Configuration-Fenster.) 8. Schritt Aktivieren Sie den Standalone-Modus (die Wiedergabe) auf dem PLEXUS. (Nutzen Sie in MADRIX den PLEXUS Configuration-Fenster.) Weiter zu 1. Schritt...
1. Schritt, 2. Schritt, 3. Schritt 1. Schritt Nutzen Sie in MADRIX den "Matrix Generator" oder den "Patch Editor". Die Kapitel in MADRIX Help And Manual finden Sie unter "Using The Software" > "Matrix Generator" bzw. "Patch Editor". 2. Schritt Das dazugehörige Kapitel in MADRIX Help And Manual finden Sie unter "Using The Software"...
Seite 224
MADRIX 3 PLEXUS User Manual / Handbuch Dateien Dateien, d.h. Aufnahmen, werden in einer großen Liste zentral dargestellt. Die Liste ist leer, wenn noch keine Aufnahmen erstellt wurden. Zielordner ("Directory") "Directory" definiert den Zielordner auf der Festplatte. Alle Aufnahmen werden in diesem Ordner gespeichert.
MADRIX PLEXUS Handbuch (Deutsch) Verwaltung von Dateien und Einträgen in der Liste Ermöglicht die Anzeige von Dateien des Typs MADRIX Record file (*.mrec) aus dem Zielordner in der Liste. Der Knopf leuchtet grün, wenn aktiviert. Deaktivieren Sie den Knopf, um alle Record-Dateien auszublenden.
MADRIX 3 PLEXUS User Manual / Handbuch "KF" Steht für Key Frames. MADRIX optimiert automatisch die Größe der Aufnahmedatei, wenn Einzelbilder identisch sind. Dadurch kann die Gesamtanzahl von Einzelbildern von der aufgenommen Anzahl an Key Frames abweichen. Wird zum Beispiel nur ein Farbwechsel mit zwei Farben verwendet, so kann die Gesamtanzahl 400 betragen.
MADRIX PLEXUS Handbuch (Deutsch) Aufnahme Wählen Sie den Reiter "Recording" aus, um eine neue Aufnahme zu erstellen. Vorbereitung Befolgen Sie bitte vor einer Aufnahme den 1., 2., und 3. Schritt. Wichtiger Hinweis Nur der sogenannte Main Output (Hauptausgabe) wird aufgenommen. Stellen Sie also sicher, dass Ihre Effekte stets auf dem Vorschaufenster in der Mitte angezeigt werden.
Sollte die Rate der Einzelbilder (FPS) zu hoch sein, können visuelle Störungen auf den LEDs auftreten. Für das MADRIX PLEXUS wird eine maximale Rate von 40 FPS empfohlen. Andernfalls, könnten PLEXUS-Geräte Einzelbilder vereinzelt weglassen, um die Zeiteinteilung (Timing) aufrechtzuerhalten sobald alle 512 Kanäle eines Universums voll belegt sind. Werden weniger als 512 Kanäle pro Universum verwendet, ist dieses Verhalten unwahrscheinlicher.
MADRIX 3 PLEXUS User Manual / Handbuch Schritt 4) Die Aufnahme erscheint in der Liste. Bearbeiten der Aufnahme Nach dem Aufnehmen kann die Datei zusätzlich bearbeitet werden. Wählen Sie zunächst die Aufnahmedatei in der Liste aus. Wechseln Sie zu dem Reiter "Record Editing"...
Seite 231
MADRIX PLEXUS Handbuch (Deutsch) Ein kleines Fenster zeigt die Aufnahme als Vorschau zur Inspektion an. Hinweis: Sollte der Schriftzug !NO MADRIX KEY! in dem Fenster erscheinen, so benutzen Sie MADRIX im Demo-Modus. Dieser Text wird jedoch später nicht in der Aufnahme enthalten sein.
Seite 232
MADRIX 3 PLEXUS User Manual / Handbuch Wählen Sie ein bestimmtes Einzelbild mit Hilfe des Schiebereglers. Nutzen Sie die kleinen, weißen Dreiecke, um ein neues "In Frame" und ein neues "Out Frame" zu definieren. Die Anzeige des aktuell ausgewählten Einzelbildes.
Seite 233
Hinweis: Der Anfang der Aufnahme wird um die eingegebene Anzahl an Einzelbilder gekürzt. Eine rote Linie unter dem Schieberegler verdeutlicht dies. Beispiel: Bei Eingabe von 100 erstellt MADRIX einen Übergang und nutzt dabei die ersten und die letzten 100 Einzelbilder. Diese werden im Anschluss ineinander übergeblendet.
Navigieren Sie in MADRIX zu dem Menü "Window" -> "Recording..." (oder "Strg+Alt+R" auf der Tastatur), um den Recording-Fenster aufzurufen. Wählen Sie zuerst Ihre Aufnahmedatei (MADRIX Record file (*.mrec)) in der Liste aus. Bitte wählen Sie nur eine Datei aus! Wechseln Sie im Anschluss zu dem Reiter "PLEXUS Conversion".
Stellen Sie sicher, dass Ihre virtuelle Matrize korrekt eingestellt ist, bevor Sie DXD- Dateien generieren (im "Patch Editor"). Hinweis: Der Reiter "PLEXUS Conversion" berücksichtigt nur die Patch-Einstellungen, jedoch nicht die Einstellungen des Device Managers in MADRIX. Sollte Ihre Live-Ausgabe über den Device Manager einwandfrei funktionieren und dort wurden die DMX-Universen bspw.
Seite 236
Master beeinflusst die Helligkeit der Hauptausgabe in MADRIX. Wurde der Master nicht verwendet oder soll nicht miteinbezogen werden, so kann diese Option deaktiviert bleiben. Hinweis: Wenn Sie mehr als 2 DMX-Universen und somit auch mehr als 1 MADRIX PLEXUS verwenden, stellen Sie bitte sicher, dass pro Gerät ein Listeneintrag hinzugefügt wurde.
Geräte werden zur Ansteuerung verwendet. PLEXUS Nummer 1 soll DMX-Universum 1 und 2 abspielen, PLEXUS Nummer 2 soll DMX-Universum 3 und 4 abspielen, PLEXUS Nummer 3 soll DMX- Universum 5 und 6 abspielen. Somit müssen 3 Listeneinträge erstellt bzw. der Knopf "Auto"...
Seite 238
2) Wie im letzten Kapitel beschrieben, gibt es eine maximal empfohlene Rate der Einzelbilder pro Sekunde (FPS) für das MADRIX PLEXUS. Diese Meldung ist ein Hinweis, dass die Rate der Aufnahmedatei höher ist als 40 FPS. Fahren Sie mit "Yes" fort. Wählen Sie "No", um abzubrechen.
6. Schritt: PLEXUS-Konfigurationen 6. Schritt: Erstellen einer PLEXUS-Konfiguration (Standalone-Show) Übersicht Navigieren Sie in MADRIX zu dem Menü "Tools" > "PLEXUS Configuration..." (oder "Strg+Alt+P" auf der Tastatur), um den PLEXUS Configuration-Fenster zu öffnen. Es wird empfohlen, die Fenstergröße des PLEXUS Configuration-Dialogs zu maximieren.
MADRIX PLEXUS Handbuch (Deutsch) Der untere Bereich ist in zwei Bereiche eingeteilt. Der linke Teil wird zum Verwalten von PLEXUS- Konfigurationen genutzt (Erstellen, Importieren/Exportiere, etc.). Der rechte Teil wird zum Editieren eine PLEXUS-Konfiguration verwendet (Szenen, Zeitgeber, Erweiterungsanschluss, etc.). Im Grunde stellt das Erstellen einer PLEXUS-Konfiguration das Erstellen einer Show für den Standalone-Modus dar.
Seite 242
SD-Karte mit einer Show in das Gerät eingesteckt wurde. "No" gibt an, dass nichts automatisch abgespielt wird. "Last Scene" gibt an, dass das PLEXUS die letzte Wiedergabe fortsetzt. Sie können auch eine bestimmte Szene auswählen. Wählen Sie dazu die genaue Nummer aus ("Scene 1", "Scene 2", "Scene 3", etc).
Netzwerkanbindung an. Die Wiedergabe wird verzögert um sicherzustellen, dass alle Slave-Geräte im Netzwerk bereit sind und nach dem Starten zur Verfügung stehen. Editieren von PLEXUS-Konfigurationen Verwenden Sie zum Editieren einer PLEXUS-Konfiguration den rechten, unteren Teil des PLEXUS Configuration-Dialogs. Erstellen Sie zuerst eine neue PLEXUS-Konfiguration, wie oben beschrieben.
Seite 244
Szenen basieren auf DXD-Dateien (DMX Data files (*.dxd)). Szenen sind Teile einer gesamten Show. Alle Szenen zusammen ergeben die gesamte Show. Wählen Sie zuerst eine PLEXUS-Konfiguration zum Editieren aus. Erstellt eine neue Szene. Beim Erstellen einer Szene erscheint ein neues Fenster. Sie werden damit aufgefordert eine DXD- Datei auszuwählen.
Seite 245
MADRIX PLEXUS Handbuch (Deutsch) Wählen Sie eine Datei aus der Liste. Oder importieren Sie eine Datei von der Festplatte mittels "Import". Nutzen Sie den Import, wenn die Liste leer ist. Entfernt eine Szene. Wählen Sie die bestehende Szene zuerst aus.
Seite 246
"Soft Loop" Erstellt einen automatischen Übergang. Geben Sie zunächst die Anzahl der Einzelbilder (Frames) ein. MADRIX fügt diese Anzahl an Frames an das Ende der Szene und erstellt einen Übergang zum ersten Einzelbild der Szene. Setzen Sie z. B. eine Rate von 66 FPS und Ihre Aufnahme wurde mit 33 FPS aufgenommen, so ergibt sich ein Übergang von 2 Sekunden.
Seite 248
Entfernt einen bestehenden Zeitgeber. Wählen Sie den bestehenden Zeitgeber zuerst aus. Dupliziert einen Zeitgeber. Wählen Sie den bestehenden Zeitgeber zuerst aus. Maximal 1000 Zeitgeber können pro PLEXUS-Konfiguration erstellt werden, um die Leistung sicherzustellen. Editieren Sie die folgenden Spalten gemäß Ihrer Anforderungen.
Seite 249
MADRIX PLEXUS Handbuch (Deutsch) "Type" Definiert, wie oft der Zeitgeber ausgelöst wird. Mögliche Werte sind: "Once", "Cycle", "Daily", "Weekly", "Monthly", "Yearly". "Once" bedeutet einmalig. "Cycle" bestimmt ein Zeitintervall, welches mit "Cycle Interval" näher definiert wird. "Daily" bedeutet täglich. "Weekly" bedeutet wöchentlich. "Monthly" bedeutet monatlich.
Seite 250
Erweiterungsanschluss Der Reiter "Extension Ports" ermöglicht die Konfiguration der individuellen Ports des Erweiterungsanschlusses. Wählen Sie zuerst eine PLEXUS-Konfiguration zum Editieren aus. Stellt die Standardeinstellungen für ausgewählte Ports wieder her. Jegliche Änderungen werden somit rückgängig gemacht. Editieren Sie die folgenden Spalten gemäß Ihrer Anforderungen.
Konvertierte Aufnahmedateien (Data Files) Der Reiter "DMX Data Files" zeigt alle verwendeten DXD-Dateien an. Somit ist es eine Datenbank aller DXD-Dateien in der PLEXUS-Konfiguration. DXD-Dateien sind die Grundlage für Szenen. Wählen Sie zuerst eine PLEXUS-Konfiguration zum Editieren aus. Fügt eine DXD-Datei hinzu.
Seite 252
"#" Zeigt die Indexnummer der Datei an. Der Wert kann nicht geändert werden. "In Use" Zeigt an, wie oft die Datei in der PLEXUS-Konfiguration als Szene verwendet wird. Der Wert kann nicht geändert werden. "File" Zeigt die vollständige Bezeichnung der Datei an. Der Wert kann nicht geändert werden.
2.3.3.5 7. Schritt, 8. Schritt: Hochladen und Abspielen 7. Schritt: Hochladen einer Standalone-Show Navigieren Sie in MADRIX zu dem Menü "Tools" > "PLEXUS Configuration..." (oder "Strg+Alt+P" auf der Tastatur), um den PLEXUS Configuration-Fenster zu öffnen. Klicken Sie , um angeschlossene Geräte zu finden.
Seite 254
B) Klicken Sie "Call" (Netzwerkverbindung erforderlich), um den Standalone-Modus aus der Ferne zu aktivieren (Wiedergabe). Weitere Informationen finden Sie im Kapitel Fernsteuerung. C) Nutzen Sie die Funktion "Auto Play" in einer PLEXUS-Konfiguration, um automatisch eine Szene zu starten. Weiter zu Tipps...
In diesem Kapitel werden Hinweise bezüglich PLEXUS Configuration-Fenster und dem Erstellen von PLEXUS-Konfigurationen und Standalone-Shows gegeben. Eine Standalone-Show kann erstellt werden, ohne dass ein MADRIX PLEXUS an den Computer angeschlossen sein muss. Um eine Standalone-Show hochzuladen, muss entweder eine SD-Karte oder ein Gerät mit eingesteckter SD-Karte angeschlossen sein.
Bestimmte Einstellungen des MADRIX PLEXUS können im PLEXUS Configuration-Fenster getätigt werden. Navigieren Sie in MADRIX zu dem Menü "Tools" > "PLEXUS Configuration..." (oder "Strg+Alt+P" auf der Tastatur), um den PLEXUS Configuration-Fenster zu öffnen. Es wird empfohlen das Fenster des PLEXUS Configuration-Fenster zu maximieren.
Lädt eine PLEXUS-Konfiguration direkt von einem PLEXUS-Gerät auf Ihre Festplatte herunter. Diese Funktion kann also beispielsweise für Sicherungskopien genutzt werden. Lädt die Geräteeinstellungen des MADRIX PLEXUS von einer externen Datei (im *. mpds Format). Nutzen Sie diese Funktion, um die in der nachstehenden Tabelle beschriebenen Einstellungen leicht wieder herzustellen.
Seite 258
MADRIX 3 PLEXUS User Manual / Handbuch Speichert die Geräteeinstellungen des MADRIX PLEXUS in eine externe Datei (im *.mpds Format). Nutzen Sie diese Funktion, um die in der nachstehenden Tabelle beschriebenen Einstellungen leicht abzuspeichern. Gleicht die Zeit und das Datum des Gerätes mit der Uhr Ihres Computers an. Der Computer gibt dabei die Zeit vor.
Seite 259
1 - 1000%. Der Standardwert ist 100%. Auf dem Gerät steht dazu das Menü "Standalone" > "Helligkeit/Tempo" zur Verfügung. "Sync" Definiert, ob PLEXUS-Geräte, die in der gleichen Gruppe sind, untereinander synchronisiert werden (Master-Slave-Synchronization). Auf dem Gerät steht dazu das Menü "Netzwerk" > "Synchronisation" zur Verfügung.
Seite 260
MADRIX 3 PLEXUS User Manual / Handbuch "Location" Definiert den geografischen Aufenthaltsort des Gerätes, inkl. der Zeitzone. Diese Daten werden zur Berechnung der Sonnenauf- und Sonnenuntergangszeiten benötigt. Auf dem Gerät steht dazu das Menü "Einstellungen" > "Standort" zur Verfügung. "SD Card"...
Seite 261
MADRIX PLEXUS Handbuch (Deutsch) "Remote Wenn Fernsteuerung über DMX aktiviert ist, kann hier ausgewählt werden, ob die Thru" eingehenden Signale zusätzlich an Art-Net weitergesendet werden sollen (DMX -> Art-Net). Auf dem Gerät steht dazu das Menü "Fernsteuerung" > "Fernst.-Optionen" zur Verfügung.
Seite 262
MADRIX 3 PLEXUS User Manual / Handbuch "DMX 2 -> wird für die Art-Net-Ausgabe im Standalone-Modus genutzt. Es zeigt an, auf Art-Net" welchem Art-Net-Universum die Daten der SD-Karte für DMX 2 gesendet werden. Auf diese Weise werden die Daten für DMX 2 zum eingestellten Art-Net-Universum weitergesendet.
Seite 263
MADRIX PLEXUS Handbuch (Deutsch) "Invert" Definiert, ob die Farben des Displays von weißem Text und schwarzem Hintergund zu schwarzem Text und weißem Hintergrund invertiert werden oder nicht. Auf dem Gerät steht dazu das Menü "Einstellungen" > "LCD-Anzeige" zur Verfügung. "Rotation"...
Installation hinweg vorgibt. Sogenannte Slave-Geräte synchronisieren sich mit diesem Master- Gerät. Nutzung Die Synchronisation von Geräten wird genutzt, um Szenen gleichzeitig auf mehreren PLEXUS- Geräten zu schalten. Das heißt, dass die LED-Installation zwar von mehreren Geräten angesteuert wird, jedoch die gleichen Effekte (bzw. ein übergreifender Effekt) zu sehen sind.
Einstellungen in der MADRIX-Software, Geräteeinstellungen und Netzwerkeinstellungen im Betriebssystem. Stellen Sie bitte sicher, dass alle PLEXUS-Geräte die selbe Firmware benutzen! Die Synchronisation kann direkt auf dem Gerät eingestellt werden. Jedoch empfiehlt sich die Konfiguration über den PLEXUS Configuration-Fenster, wie im Folgenden beschrieben.
Seite 266
MADRIX 3 PLEXUS User Manual / Handbuch PLEXUS Configuration-Fenster Navigieren Sie in MADRIX zu dem Menü "Tools" > "PLEXUS Configuration..." (oder "Strg+Alt+P" auf der Tastatur), um den PLEXUS Configuration-Fenster zu öffnen. Wählen Sie Ihr Gerät in der Liste aus. Ändern Sie die Einstellungen für jedes Gerät.
Seite 267
MADRIX PLEXUS Handbuch (Deutsch) "Off" deaktiviert die Synchronisation für dieses Gerät. "Master" definiert das PLEXUS als Hauptgerät in der Gruppe, welches die Synchronisation vorgibt (Master). "Slave" definiert das Gerät als abhängig gesteuertes Gerät, welches sich mit dem "Master" synchronisiert. "Slave With Intensity"...
Seite 268
Master-Gerät diese Einstellungen. Das Master-Gerät kommuniziert die Timer automatisch mit dem Slave-Gerät. Timer können im PLEXUS Configuration-Fenster konfiguriert werden. Wird die "Master-/Slave-Synchronization" verwendet, so werden auch mehrere PLEXUS-Geräte genutzt. Beachten Sie dabei die richtigen Einstellungen beim Aufnehmen (4. Schritt: Aufnahme) und Konvertieren (5.
MADRIX PLEXUS Handbuch (Deutsch) Gruppierung ("Group") Navigieren Sie in MADRIX zu dem Menü "Tools" > "PLEXUS Configuration..." (oder "Strg+Alt+P" auf der Tastatur), um den PLEXUS Configuration-Fenster zu öffnen. Wählen Sie Ihr Gerät in der Liste aus. Ändern Sie die Einstellungen für jedes erforderliche Gerät.
Version 1.00.2981 Veröffentlicht zusammen mit: MADRIX 2.13 - July 2011 Setzt PLEXUS-Treiber 6.0.510.5 voraus. Dies ist die erste Firmware-Version des MADRIX PLEXUS. Das Produkt wurde zur Markteinführung mit dieser Version ausgeliefert. Version 1.01.3053 Veröffentlicht zusammen mit: MADRIX 2.13a - August 2011 Setzt PLEXUS-Treiber 6.0.510.5 voraus.
Seite 272
(wie z.B. Hoch- und Runterladen von Dateien). Verbesserter Highlight-Modus: Das LCD-Grafikdisplay des ausgewählten Gerätes leuchtet nun auf, wenn "Highlight Device" gerade im Device Manager von MADRIX aktiv ist. Neue Statusmeldungen für das Status-Menü wurden hinzugefügt (z.B. beim Hoch- und Runterladen von Dateien).
Seite 273
Invertieren für die LCD-Anzeige aktiviert war. Art-Net-Universen werden nun von 1 bis 256 dargestellt, anstatt von 0 bis 255. Eine Vielzahl an Einstellungen für das Gerätes kann jetzt über den PLEXUS Configuration-Fenster in MADRIX erfolgen, wohingegen diese Einstellungen vorher nur über das Gerät erreichbar waren.
Seite 274
MADRIX 3 PLEXUS User Manual / Handbuch Version 1.05.4001 Veröffentlicht zusammen mit: MADRIX 2.14a - Juli 2012 Setzt PLEXUS-Treiber 6.0.516.0 voraus. Beseitigung eines Fehlers: Die Uhrzeit des Gerätes konnte nach einer Weile unverhältnismäßig abweichen. Beseitigung eines Fehlers: Die Synchronisation von Geräten bzgl. der Master-Slave Synchronization wurde verbessert.
Seite 275
Veröffentlicht zusammen mit: MADRIX 2.14b (2.14.2.1) - Dezember 2012 Ebenso gültig für: MADRIX 3.0 (3.0.0.5) - Juli 2013 / MADRIX 3.0a (3.0.1.0) - September 2013 / MADRIX 3.1 (3.1.0.1) - November 2013 / MADRIX 3.1a (3.1.1.1) - Januar 2014 / MADRIX 3.2 (3.2.0.3) - März 2014...
Seite 276
Frames im Standalone-Betrieb zu senden. Das kann bei Fixture-Geräten helfen, die immer alle 512 DMX-Kanäle pro Bild benötigen. Verändertes PLEXUS-Menü: Die Position und der Name des Menüs "Einstellungen" > "Netzwerk" zu "Netzwerk" > "IP-Adresse". Lange Namen von Konfigurationen oder Geräten werden als Lauftext im Menü "Informationen" >...
Seite 277
über die auf der SD-Karte gespeicherten Szenen angezeigt werden, wenn man von dem Menü "Standalone" > "Szenen" dort hin wechselte. Version 1.08.5780 Veröffentlicht zusammen mit: MADRIX 3.5a (3.5.1.0) / December 2015 Setzt PLEXUS-Treiber 6.0.0518.2 voraus. Beseitigung eines Fehlers: Ein Gerät reagierte unter Umständen nicht mehr wenn eine hohe Geschwindigkeit (zum Beispiel 400%) im Menü...
Seite 278
Geräte nutzen jetzt das Kompilierungsdatum der Firmware und setzen die Zeit auf 12:34:00 nach einem Batteriewechsel oder bei Erstbenutzung des Gerätes, anstatt nur Nullen anzuzeigen. Beseitigung eines Fehlers: Das Grafikdisplay blinkte weiter nachdem in MADRIX die Funktion zum Auffinden des Gerätes über Art-Net genutzt wurde.
In MADRIX 1) Schließen Sie das PLEXUS mit Ihrem PC über USB an. 2) Navigieren Sie in MADRIX zu dem Menü "Tools" > "PLEXUS Configuration..." (oder "Strg+Alt+P" auf der Tastatur). 3) Wenn das Gerät bereits von MADRIX erkannt wurde, wird eventuell eine Information angezeigt, dass die Firmware nicht mehr aktuell ist.
Fenster "PLEXUS Configuration", wenn das Gerät nicht in der Liste angezeigt wird. 4) Wählen Sie Ihr MADRIX PLEXUS in der Liste aus. Sie können auch mehrere Geräte auswählen. 5) Klicken Sie den Knopf "Firmware". Folgen Sie eventuellen Anweisungen auf dem Bildschirm.
Die Hardware des Gerätes kann vom Hersteller im Laufe der Zeit für neue Geräte aktualisiert werden. Bitte beachten Sie dazu folgende Hinweise: Hardwareversion V1.6 ("Model: PLEXUS V1.6") kann problemlos mit Firmware-Version 1.07.4369 oder höher aktualisiert werden. Hardwareversion V1.7 ("Model: PLEXUS V1.7") setzt mindestens Firmware-Version 1.06.4260 oder höher voraus!
MADRIX 3 PLEXUS User Manual / Handbuch MADRIX PLEXUS Updater (Zusatzprogramm) 2.4.3 Überblick Ein separates Programm wird zusammen mit MADRIX für MADRIX PLEXUS bereitgestellt: 'MADRIX PLEXUS Updater'. Nutzung MADRIX PLEXUS Updater ist ein Programm für fortgeschrittene Nutzer. Es sollte nicht ohne Grund verwendet werden! Das Programm wird hauptsächlich genutzt, wenn es unmöglich ist, die MADRIX-Software aus...
Seite 283
Aktualisiert die Firmware aller PLEXUS-Geräte, die über USB verbunden sind. Wählen Sie zunächst die korrekte Firmware- Version aus der Liste darüber aus (Beispiel: "PLEXUS 1.0.000 Type V1.0-V1.6 MADRIX 3.0"). Klicken Sie im Anschluss diesen Knopf. Nach der Aktualisierung sollte das Gerät vom Strom getrennt werden, um es neu zu starten.
Seite 284
Wo finde ich MADRIX PLEXUS Updater? MADRIX PLEXUS Updater ist in der Installationsdatei von MADRIX enthalten. Nach dem Installieren von MADRIX steht eine Verknüpfung zum Programm im Windows Start-Menü zur Verfügung: "Start" > "Programme" > "MADRIX 3" > "Tools" > "MADRIX PLEXUS Updater"...
Brauche ich den MADRIX KEY zusätzlich zum MADRIX PLEXUS? Nein. Die MADRIX-Softwarelizenz für 1024 DMX-Kanäle ist inbegriffen und wird automatisch bei Verbindung zu MADRIX aktiviert. Der MADRIX KEY wird für den Betrieb des PLEXUS nicht benötigt. Allerdings kann man die Produkte und ihre Funktionen miteinander kombinieren.
Seite 286
Effekten und Abläufen bestehen. Wie kann ich meine LEDs ausschalten (am Ende des Tages z.B.)? Erstellen Sie hierzu eine Szene mit der Farbe Schwarz und lassen Sie das PLEXUS diese Szene zur gegebenen Zeit dann abspielen. Kann das MADRIX PLEXUS Audiodaten live empfangen und verarbeiten, um damit Standalone-Effekte zu erstellen? Nur die MADRIX-Software kann Audiodaten live verarbeiten.
MADRIX PLEXUS Handbuch (Deutsch) Hilfe und Fehlerbehebung Anzeige der Status-LEDs Die folgenden Tabellen beschreiben die Funktionen der drei Status-LEDs. USB/Strom FARBE STATUS-LED USB/POWER (USB/STROM) USB/Power ist nicht angeschlossen. Au s g e s ch a lte n Das Gerät hat keinen Strom.
MADRIX 3 PLEXUS User Manual / Handbuch SD-Kartendaten werden gelesen oder geschrieben. Grün blinkend Das Gerät funktioniert und arbeitet. Überblenden zwischen Eine SD-Karte ist in das Gerät eingesteckt. grün Keine Daten werden gelesen oder geschrieben. Der Gerätetreiber des MADRIX PLEXUS Wenn Windows anzeigt, dass der Gerätetreiber nicht korrekt installiert werden konnte, so...
Seite 289
Die Hardware des Gerätes kann vom Hersteller im Laufe der Zeit aktualisiert werden. Bitte beachten Sie dazu folgende Hinweise: Hardwareversion V1.6 ("Model: PLEXUS V1.6") kann problemlos mit Firmware-Version 1.07.4369 oder höher aktualisiert werden. Hardwareversion V1.7 ("Model: PLEXUS V1.7") setzt mindestens Firmware-Version 1.06.4260 oder höher voraus! Nutzen Sie bitte keine vorherige Version.
Das PLEXUS wird im Geräte-Manager von Windows angezeigt. Jedoch erkennt MADRIX das Gerät nicht! 1) Überprüfen Sie, ob die USB-Treiber in MADRIX in den "Options" aktiviert sind. 2) Aktualisieren Sie den Geräte-Treiber, wie oben beschrieben. Dies könnte nach eine Firmware-Aktualisierung nötig sein.
MADRIX PLEXUS Handbuch (Deutsch) Ein separates Programm wird zusammen mit MADRIX für MADRIX PLEXUS bereit gestellt: 'MADRIX PLEXUS Updater'. Das Programm kann zum Aktualisieren der Firmware sowie zum Zurücksetzen des Gerätes auf seine ursprünglichen Einstellungen genutzt werden. Weitere Informationen finden Sie im Kapitel MADRIX PLEXUS Updater (Zusatzprogramm).
Seite 292
3. Schritt: Verbinden Sie USB/Power wieder, während Sie noch immer die drei Tasten drücken und halten. 4. Schritt: Der Bootlader wird nun geladen. 5. Schritt: Die Firmware des PLEXUS kann nun neu aufgespielt werden mit Hilfe des Zusatzprogrammes MADRIX PLEXUS Updater.
MADRIX 3 PLEXUS User Manual / Handbuch Änderungen und Irrtümer vorbehalten. Reproduktion, Adaption oder Übersetzungen sind ohne vorherige, schriftliche Erlaubnis nicht gestattet. Dieses Handbuch wurde mit größter Sorgfalt verfasst. inoage GmbH gibt jedoch keine Gewähr hinsichtlich Richtigkeit, Marktfähigkeit oder Eigenschaften des Produkts. Es gibt keinen rechtlichen oder anderen Weg, Anspruch gegenüber inoage GmbH zu erheben.