Unold Backmeiser 68615 Bedienungsanleitung Seite 33

Program Program name
number
8 TEIG
DOUGH
9 ULTRA-
SCHNELL
ULTRA-FAST
10 BACKEN
BAKE
11 SÜSSSPEISEN
DESSERT
BRÄUNGUNGsGRaD/BROWNING
With this button you can set the degree of browning to HELL/
LIGHT – MITTEL/MEDIUM – DUNKEL/DARK. This function is not
available in the following programs: JAM, DOUGH and the user
program. The selected setting is shown on the display.
BROtGRÖsse/lOaF sIze
This button is used to select the size of the loaf in various
programs:
STUFE/LOAF SIZE I = for smaller loaves (approx. 500-850 g)
STUFE/LOAF SIZE II = for larger loaves (approx. 850-1,200 g)
Please note that it is not possible to select the loaf size in the
following programs: BAKING POWDER, JAM, DOUGH, BAKE and
DESSERT. You will find our recommendations in the recipes. The
selected setting is shown on the display.
You can also bake smaller loaves by reducing the quantities by
one-half, e.g. for singles and small households. In this case, we
recommend that you always use the BASIC program on LOAF
SIZE I. Please be aware, however, that the loaf will be relatively
flat in this case.
PaUse
The PAUSE button can be used to briefly interrupt the program,
for example to remove the kneader from the dough or to brush
the surface of the bread with water or milk, etc. Press the PAUSE
button for about 1 second to interrupt the current program.
When the display blinks, you know that the program has been
interrupted. Now you can remove the kneader or brush the surface
of the bread. Then close the lid. To resume the program, press
the PAUSE button again for about 1 second. The display stops
blinking and the program continues.
CAUTION: Do not interrupt the program for more than about
5 minutes. Longer interruptions can affect the rising of the dough
and ruin the bread.
As long as the pause function is active (i.e. the display is blinking),
the START/STOP button is locked and the program cannot be
completely discontinued.
lIcht/lIGht
The Backmeister Skala is equipped with lights for the baking
®
compartment, so you can observe the progress of the dough or of
the bread at any time without having to open the lid. The baking
compartment is not lighted throughout the entire program. To
check the dough, press the LICHT button to turn on the light
in the baking compartment. After one minute, or as soon as you
press the button again, the light goes out.
Program description
For preparing dough, without
baking
This program is suitable for
light breads made of superfine
flour (wheat or a mixture of
wheat and spelt). This program
is not suitable for whole grain
bread or rye bread, nor should
it be used for sourdough bread.
For baking of yeast or batter
dough that has been prepared
separately (either by hand or
in the DOUGH program). This
program is not suitable for pie
dough or choux pastry dough.
For baking sweet baked goods.
BUttON lOcK
To prevent accidental pressing of the buttons, e.g. by children,
you can lock the buttons. If you first press the ABSCHNITT button
and then the BROWNING button, you will hear three beeps,
indicating that the buttons (with the exception of ABSCHNITT
and BRÄUNUNGSGRAD) are deactivated. To turn off the button
lock function, press the ABSCHNITT button again and then the
BRÄUNGSGRAD button and wait for the three beeps. Please note:
when the button lock function is on, the scale cannot be used.
eIGeNPROGRaMM/UseR PROGRaM
In addition to the other numerous programs provided by the
BACKMEISTER you can also program your own USER PROGRAM.
®
You can change the basic time and program phase settings as
programmed at the factory or leave out various program phases.
This allows you to develop your own individual program for baking
bread or preparing dough. Below you will find a sample recipe.
First you should become familiar with the following information
on the basic programming and use of the USER PROGRAM.
USER PROGRAM
The program features the following options
Browning not programmable
Timer programmable
Loaf size I and II not programmable
The default program is the same as for the BASIC program.
Phase Preset
Total time 3:00 hours
Knead 1 10 minutes
Rise 1 20 minutes
Knead 2 15 minutes
Rise 2 25 minutes
Rise 3 45 minutes
Bake 65 minutes
Keep warm 60 minutes
The times can be programmed as shown in the table.
Proceed as follows:
Select the USER PROGRAM with the Menu button.
Select the desired phase with the ABSCHNITT button. Knead
1 and the programmed time 0:10 for this phase appear on the
display.
The time can be changed by means of the ZEITWAHL button.
Press it repeatedly until the desired time appears on the display
(past OFF, if necessary).
Confirm the change with the ABSCHNITT button. Press this
button again and the next program phase and the programmed
time will appear on the display: Rise 1 = and 0:20.
If the maximum programmable time for the respective program
phase is exceeded by pressing the ZEITWAHL button, O will
appear on the display if this is possible according to the above
table. This phase is then skipped during the program.
Every programmed setting must be confirmed by pressing the
ABSCHNITT button, so you can continue programming the next
program phase.
Once you have programmed all phases to suit your preferences,
conclude the programming by pressing the ABSCHNITT button
and then the START/STOP button. The programmed time for the
user program appears on the display. The program then starts
either immediately or after the time set via the timer function.
Programmable time frame
6-14 minutes
20-60 minutes
5-20 minutes
5-120 minutes
0-120 minutes
0-80 minutes
0-60 minutes
33