Intended Use; Safety Information - Scheppach HS105 Bedienungsanleitung

• Operating manual
• Saw with pre-installed saw blade
• Saw blade guard
• Extraction hose
• Riving knife
• Rip fence
• Fence rail
• Cross stop
• Table width extension (1x)
• Push stick
• Legs (4x)
• Cross struts (2x)
• Longitudinal struts (2x)
• Central struts, short (2x)
• Central struts, long (2x)
• Rubber feet (4x)
• Assembly material

4. Intended use

The bench-type circular saw is designed for the slit-
ting and cross-cutting of all types of timber, commen-
surate with the machine's size.
The machine is not to be used for cutting any type of
roundwood.
The machine is to be used only for its prescribed pur-
pose. Any use other than that mentioned is consid-
ered to be a case of misuse. The user/operator and
not the manufacturer shall be liable for any damage
or injury resulting such cases of misuse.
The machine is to be operated only with suitable saw
blades. It is prohibited to use any type of cutting-off
wheel. To use the machine properly you must also
observe the safety regulations, the assembly instruc-
tions and the operating instructions to be found in this
manual. All persons who use and service the machine
have to be acquainted with this manual and must be
informed about its potential hazards. It is also impera-
tive to observe the accident prevention regulations in
force in your area. The same applies for the general
rules of occupational health and safety.
m Important!
When using the equipment, a few safety precautions
must be observed to avoid injuries and damage.
Please read the complete operating instructions and
safety regulations with due care. Keep this manual in
a safe place, so that the information is available at all
times. If you give the equipment to any other person,
hand over these operating instructions and safety
regulations as well. We cannot accept any liability for
damage or accidents which arise due to a failure to
follow these instructions and the safety instructions.
The manufacturer shall not be liable for any changes
made to the machine nor for any damage resulting
from such changes.
26 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Even when the machine is used as prescribed it is still
impossible to eliminate certain residual risk factors.
The following hazards may arise in connection with
the machine's construction and design:
• Contact with the saw blade in the uncovered saw
zone.
• Reaching into the running saw blade (cut injuries).
• Kick-back of workpieces and parts of workpieces
• Saw blade fracturing.
• Catapulting of faulty carbide tips from the saw
blade.
• Damage to hearing if essential ear-muffs are not
worn.
• Harmful emissions of wood dust when the machine
is used in closed rooms.
m Please note that our equipment has not been de-
signed for use in commercial, trade or industrial ap-
plications. Our warranty will be voided if the machine
is used in commercial, trade or industrial businesses
or for equivalent purposes.

5. Safety information

m Attention! The following basic safety measures
must be observed when using electric tools for pro-
tection against electric shock, and the risk of inju-
ry and fire. Read all these notices before using the
electric tool and keep the safety instructions for later
reference.
Safe work
1 Keep the work area orderly
– Disorder in the work area can lead to accidents.
2 Take environmental influences into account
– Do not expose electric tools to rain.
– Do not use electric tools in a damp or wet en-
vironment.
– Make sure that the work area is well-illuminated.
– Do not use electric tools where there is a risk of
fire or explosion.
3 Protect yourself from electric shock
– Avoid physical contact with earthed parts (e.g.
pipes, radiators, electric ranges, cooling units).
4 Keep children away
– Do not allow other persons to touch the equip-
ment or cable, keep them away from your work
area.
5 Securely store unused electric tools
– Unused electric tools should be stored in a dry,
elevated or closed location out of the reach of
children.
6 Do not overload your electric tool
– They work better and more safely in the speci-
fied output range.
7 Use the correct electric tool
– Do not use low-output electric tools for heavy
work.