Bosch EPS 205 Originalbetriebsanleitung Seite 52

en 52 | EPS 205 | Commissioning
4.3 Fitting guard
1. Take the guard out of the packaging material and set
it down on the packaging material.
2. Remove the parts of the assembly set 1 685 510 239
from the packaging.
The assembly set 1 685 510 239 contains the following:
R
Handle with
$
Hexagon socket head bolt M6 x 16 (2x)
$
Plastic washer 18 x 6 x 0.5 mm (2x)
$
Spring lock washer A6 (2x)
R
Hexagon socket head bolt M5x16 with
$
Plastic washer 15 x 5 x 0.5 mm (2x)
$
Spring lock washer A5
$
Nut M5
R
Ball bearing (2 x) with
$
Plastic washer 25 x 10 x 1.5 mm (2x, black)
$
Retaining ring (4x, 2x as spares)
$
Fitted washers 16 x 10 x 0.5 mm (6x)
R
Retaining plate (2x) with
$
Spring holder (2 x) with
$
Plastic washer 15 x 5 x 0.5 mm (8x)
$
Spring lock washer A5 (4 x)
$
Nut M5 (4x)
1 2 3
8
6
7
7
6
5
Fig. 34: Fitting handle and guard detection system
1 Hexagon socket head bolts M6 x 16
2 Spring lock washer A6
3 Plastic washers 18 x 6 x 0.5 mm
4 Handle
5 Hexagon socket head bolt M5 x 16
6 Spring lock washer A5
7 Plastic washer 18 x 6 x 0.5 mm
8 Nut M5
|
1 689 989 185 2018-03-24
Fitting handle
¶
Attach the handle (Fig. 34, item 4) to the guard
using hexagon socket head bolts M6x16 (Fig. 34,
item 1), spring lock washers A6 (Fig. 34, item 2) and
plastic washers 18 x 6x 0.5 mm (Fig. 34, item 3).
Fitting guard detection system
¶
Fit the hexagon socket head bolt M5 x 16 (Fig. 34,
item 5), spring lock washer A5 (Fig. 34, item 6) and
plastic washer 15 x 5 x 0.5 mm (Fig. 34, item 7) with
the nut M5 (Fig. 34, item 8) at the guard.
i
With the EPS 205 switched on and the guard closed,
the LED at the inner guard contact must light. If
this is not the case, the distance between the guard
contacts must be reduced. To do so, unfasten
the nuts at the guard contact and move the guard
contact to the correct position.
Fitting guard on shaft
4
1
Fig. 35: Fitting guard on shaft
1 Mounting hole
2 Retaining ring
3 Ball bearing
4 Plastic washer 25 x 10 x 1.5 mm (black)
5 Shaft
!
Take care not to scratch the guard when fitting
it on the shaft. Excessive expansion may damage
the protective hood. Take care not to scratch the
protective hood.
1. Fit black plastic washers 25 x 10 x 1.5 mm (Fig. 35,
item 4) on both ends of the shaft (Fig. 35, item 5).
2. Place the guard in the correct position on the
EPS 205.
3. Carefully stretch the guard with both hands on a
level with the two mounting holes and position the
two mounting holes (Fig. 35, item 1) of the guard
over the ends of the shaft.
4 5
3
2
Robert Bosch GmbH
4
3
2