HEIDENHAIN TNC 407 Technisches Handbuch Seite 749

M
M-Funktionen .........................................4-139
Mittenversatz..........................................4-178
MOD (MODULO) ...................................7-70
MOD [ ] (MODULO [ ]) ...........................7-86
modaler Zyklus-Aufruf ............................4-162
Modul 9000/9001 ...................................7-136
Modul 9010/9011/9012 ..........................7-137
Modul 9020/ 9021/ 9022 ........................7-138
Modul 9031 ............................2-19; 5-5; 7-139
Modul 9032 ...................................2-19; 7-140
Modul 9033 ...................................2-23; 7-140
Modul 9035 ..........................2-20; 2-22; 7-141
Modul 9036 ............................................7-144
Modul 9040/9041/9042 ..........................7-145
Modul 9041 ..............................................2-19
Modul 9050 ............................................7-147
Modul 9051 ............................................7-148
Modul 9052 ............................................7-149
Modul 9053 ............................................7-150
Modul 9054 ............................................7-150
Modul 9070 .................................4-141; 7-151
Modul 9071 .................................4-141; 7-152
Modul 9080 ......................4-141; 7-114; 7-152
Modul 9081 .................................4-141; 7-153
Modul 9082 ......................4-141; 7-114; 7-153
Modul 9083 ........................2-19; 4-141; 7-155
Modul 9090 ............................................7-157
Modul 9093 ..............................................2-19
Modul 9093/9094 ...................................7-158
Modul 9094 ..............................................2-19
Modul 9095 ............................................7-161
Modul 9100 ............................................7-163
Modul 9101 ............................................7-163
Modul 9102 ............................................7-164
Modul 9103 ............................................7-165
Modul 9104 ............................................7-165
Modul 9105 ............................................7-167
Modul 9106 ............................................7-167
Modul 9107 ............................................7-168
Modul 9110 ............................................7-169
Modul 9111 ............................................7-170
Modul 9120 ............................................7-171
Modul 9121 ............................................7-172
Modul 9122 ............................................7-172
Modul 9123 ............................................7-173
Modul 9130 ............................................4-275
Modul-Aufruf (CM)................................7-107
Modul-Ende ............................................7-110
Modultechnik............................................7-17
MSB............................................................8-6
Multiplikationsfaktor .................................4-72
MULTIPLIZIEREN (x) ..............................7-68
MULTIPLIZIEREN [ ] (x[ ]) .......................7-85
13-8 TNC 407/TNC 415/TNC 425
N
N ...............................................................8-18
Näherungs-Schalter ................................4-223
NC-Software ...............................................2-8
NC-Start ..................................................4-174
Negative Lose...........................................4-23
Nichtlineare Achsfehler-Kompensation ....4-27
Nichtlineare Achsfehler-Korrektur...........7-161
nichtlinearen Kennlinie............................4-138
Normalen-Richtung.................................4-181
NOT-AUS-Routine........................4-189; 4-262
Nullpunkt-Korrektur.................................4-221
Nullpunkt-Tabelle .....4-150; 4-151; 7-157; 8-18
Nullpunkt-Verschiebung..........................4-132
Null-Referenzmarke ..................................4-53
O
O (OR).....................................................7-57
O[ ] (OR [ ]...............................................7-80
ODER (O)................................................7-57
ODER [ ] (O[ ]..........................................7-80
ODER NICHT (ON)..................................7-59
ODER NICHT [ ] (ON[ ])...........................7-80
Offset-Abgleich.2-24; 4-75; 4-77; 4-104; 4-274
ON (OR NOT)..........................................7-59
ON[ ] (OR NOT [ ])...................................7-80
Operand ....................................................7-16
Operandenteil ...........................................7-16
Operanden-Übersicht ...............................7-18
Orientierung............................................4-106
Oszilloskop .............................................11-17
Oszilloskop-Funktion.................................2-22
OUTPUT BINARY CODE 0001 .................7-10
Overflow .................................................7-123
Override ................................2-19; 2-20; 4-138
OVWR (OVERWRITE)...........................7-116
Stichwortverzeichnis 11.97