Ryobi RBC30SESC Bedienungsanleitung Seite 29

operator to lose control of the unit. Blade thrust may
occur without warning if the blade snags, stalls or binds.
This is more likely to occur in areas where it is diffi cult to
see the material being cut. For cutting ease and safety,
approach the weeds being cut from the right to the left.
In the event that an unexpected object or woody stock is
encountered, this could minimise the blade thrust reaction.
CUTTING TECHNIQUE - BLADE (Fig. 8)
WARNING
Extreme care must be taken when using blades
to ensure safe operation. Read the safety
information for safe operation using the blade,
refer to "Brushcutter Safety Rules" earlier in this
manual.
MAINTENANCE
WARNING
Use only original manufacturer's replacement
parts, accessories and attachments. Failure to
do so can cause possible injury, poor perfor-
mance and may void your warranty.
■ The cutting attachment must not work in idle mode.
If this requirement is not satisfied, the clutch has
to be adjusted or the machine needs an urgent
maintenance by a qualified technician.
■ You may make adjustments and repairs described
here. For other repairs, have the product serviced by
an authorized service agent.
■ Consequences of improper
include excess carbon deposits resulting in loss of
performance and discharge of black lubricant residue
dripping from the muffler.
■ Make sure all guards, straps, deflectors and handles
are properly and securely attached to avoid the risk of
personal injury.
STRING REPLACEMENT (Fig. 9)
TM
REEL EASY
■ Ensure the unit is in the off position
■ Remove the spark plug lead to prevent accidental
starting.
■ Use a 2.4mm diameter monofilament string.
■ Cut one piece of string approximately 6 m in length.
■ Rotate the knob on the string head until the line on
knob aligns with the arrows on the top of string head.
■ Insert one end of the string into the eyelet located on
the side of the string head and push until string comes
out through eyelet on the other side. Continue to push
string through the string head until the middle section
of the string is inside the string head and string outside
the string head is evenly divided on each side.
English (Original instructions)
■ Rotate the knob on the string head clockwise to wind
■ Wind the string until approximately 20cm remains
BLADE PROTECTOR (Fig. 10)
Always place the blade protector on the blade when the
unit is not in use. The blade protector has clips round the
edges to snap over the blade and keep it in place. Wear
gloves and be cautious when handling the blade.
NOTE: Always remove the blade protector before using
the unit. If not removed, the blade protector could become
a thrown object as the blade begins to turn.
CLEANING THE EXHAUST PORT AND SILENCER
Depending on the type of fuel used, the type and amount
of lubricant used, and/or your operating conditions, the
exhaust port and silencer may become blocked with
carbon deposits. If you notice a power loss with your petrol
powered tool, a qualifi ed service technician will need to
remove these deposits to restore performance.
SPARK ARRESTOR
It is recommended to clean or replace the spark arrestor
every 25 hours to ensure proper performance of your
product. Spark arrestors may be in different locations
depending on the model purchased. Please contact your
nearest service dealer for the location of the spark arrestor
for your model.
maintenance may
ATTACHING THE HANGER CAP (Fig. 11)
To use the hanger cap, push in the button and place the
hanger cap over the lower end of the attachment. Slightly
rotate the cap from side to side until the button locks into
place.
NOTE: The secondary hole in the attachment shaft can be
used for hanging purposes as well.
CLEANING THE AIR FILTER (Fig. 12)
For proper performance and longer life, keep the air fi lter
clean.
■ Ensure the unit is in the off position
■ Remove the air filter cover.
■ Remove the air filter and clean it with warm soapy
■ Rinse, and let the air filter dry completely.
■ Work two drops of lubricant into the air filter.
■ Replace the air filter (fits only one way).
■ Replace the air filter cover.
NOTE: The air fi lter should be replaced annually for the
best performance.
27
the string.
protruding from the string head.
water.
NOTE: If damaged, replace immediately.