Ryobi RBC30SESC Bedienungsanleitung Seite 28

NOTE: After the 7th press, the fuel should be visible
in the primer bulb. If not, continue pressing until the
fuel is visible.
3. Set the choke lever (2) to
4. Hold down the throttle lock and then squeeze
the throttle trigger. Lock the throttle in position by
depressing the throttle interlock button .
5. Hold the foam handle tightly with left hand and pull
the starter grip upwards with right hand in a quick,
fi rm and consistent motion until the engine attempts
to start. Do not pull the starter grip more than 4 times.
6. Set the choke lever to
7. Pull the starter grip until the engine starts. Do not pull
the starter grip more than 6 times.
NOTE: If the engine does not start, repeat the
procedure from step 3.
8. Allow the engine to run for 10 seconds, then set the
choke lever to position.
RBC30SESC
1. Lay the product on a fl at, bare surface.
2. Press the primer bulb (1) 10 times.
NOTE: After the 7th press, the fuel should be visible
in the primer bulb. If not, continue pressing until the
fuel is visible.
3. Set the choke lever (2) to
4. Squeeze the throttle trigger completely and pull the
starter grip until the engine attempts to start. Do not
pull the starter grip more than 4 times. Keep the
throttle trigger squeezed completely.
5. Set the choke lever to
6. Pull the starter grip until the engine starts. Do not pull
the starter grip more than 6 times.
NOTE: If the engine does not start, repeat the
procedure from step 3.
7. Allow the engine to run for 10 seconds, then set the
choke lever to position.
TO START A WARM ENGINE:
RBC30SBSC
1. Press the primer bulb 10 times.
2. Set the choke lever to
3. Hold the foam handle tightly with left hand and pull
the starter grip upwards with right hand in a quick,
fi rm and consistent motion until the engine starts.
RBC30SESC
1. Press the primer bulb 10 times.
2. Set the choke lever to
3. Pull the starter grip until the engine starts.
OPERATING THE TRIMMER (Fig. 5)
RBC30SESC : Hold the product with the right hand on the
English (Original instructions)
choke position.
choke position.
choke position.
choke position.
choke position.
choke position.
rear handle and the left hand on the front handle.
RBC30SBSC: Hold the product with the right hand on the
trigger handle and the left hand on the left handle.
Keep a fi rm grip with both hands while in operation. The
product should be held at a comfortable position with the
trigger handle or rear handle about hip height.
Always operate the product at full throttle. Prolonged
cutting at partial throttle will result in lubricant dripping
from the silencer. Cut tall grass from the top down.
This will prevent grass from wrapping around the shaft
housing and string head which may cause damage from
overheating. If grass becomes wrapped around the string
head, stop the engine, disconnect the spark plug wire, and
remove the grass.
CUTTING TIPS (Fig. 6)
When cutting, make sure the cutter head is at a slight
angle as shown while still approximately parallel to the
ground surface. In tall grass, cut from the top down to
ensure the moving parts do not get tangled with the long
grass / brush.
Move the head in steady strokes from left to right as you
work through the grass / brush.
ADVANCING THE LINE (Fig. 7)
TM
REEL EASY
Line advance is controlled by tapping the string head on
grass while running engine at full throttle.
■ Run engine at full throttle.
■ Tap the knob on ground to advance string. The string
advances each time the knob is tapped. Do not hold
the knob on the ground.
OPERATING THE BRUSHCUTTER (Fig. 5)
RBC30SESC: Hold the product with the right hand on the
rear handle and the left hand on the front handle.
RBC30SBSC: Hold the product with the right hand on the
trigger handle and the left hand on the left handle.
Keep a fi rm grip with both hands while in operation. The
product should be held at a comfortable position with the
trigger handle or rear handle about hip height. Maintain your
grip and balance on both feet. Position yourself so that you
will not be drawn off balance by the kick-back reaction of the
cutting blade.
Adjust the harness to position the product at a comfortable
operating position and to assure that the harness will
reduce the risk of operator contact with the blade.
Exercise extreme caution when using the blade with this
unit. Blade thrust is the reaction which may occur when
the spinning blade contacts anything it cannot cut. This
contact may cause the blade to stop for an instant, and
suddenly "thrust" the unit away from the object that was hit.
This reaction can be violent enough to cause the
26