Manual.adjustment.of.end.points; Manually Setting The Upper End Point And Automatically Setting The Lower End Point - RADEMACHER RolloTube I-line Funk Small Montageanleitung

Manual adjustment of end points
Initial installation
For.initial.installation,.the.roller.shutter.engineer.can.carry.out.the.end.point.configuration.
with.the.help.of.the.set button (11) on.the.motor.or.with.a.commercially.available.
cord switch device (22).or.external.switch.
Further.information.can.be.obtained.from.the.cord.switch.device.operating.instructions.
IMPORTANT
◆ Operating the equipment without a stopper (20) may cause the roller
shutters to run into the roller shutter box and be damaged.
. The.roller.shutters.must.always.be.fitted.with.a.stopper.(20).or.end-rail.
. ◆ End.points.must.be.set.in.order.to.switch.off.the.motor.when.they.are.reached.for. .
. both.directions.of.travel.(up./down).
Manually setting the upper end point and automatically setting the lower end point
1.
or
2.
or
SET
3.
4
5.
6.
or
SET
7.
or
46
Symbols and actions when connecting a cord circuit setting unit (22)
or
when connecting an external switch.
Switch on the mains power.
ON
First move the roller shutters upwards.
If.the.tubular.motor.is.already.logged.on.to.the.DuoFern.network,.then.the.direction.of.travel.can.also.be.specified.with.DuoFern.transmitters..
This.also.applies.to.point.6.
IMPORTANT
. ◆ First.move.the.roller.shutters upwards..If.the.roller.shutters.first.move.downwards,.then.the.direction.of.travel.must.first.be.reversed.by.
. pressing.the.SET button.several.times.or.by.using.the.external switch..
. ◆ The.switching.sequence.for.the.SET button.or.the.external switch.is:.OPEN/STOP/CLOSE/STOP, and so on.
Press and hold the corresponding set button (11) until the upper end point is reached.
Release the set button (11) as soon as the roller shutters have reached the desired position.
The.motor.stops.and.the.upper.end.point.is.stored.
You can correct the end point in small steps by briefly pressing the set button (11).
Important
In.the.event.that.a.malfunction.occurs.during.configuration,.e.g..in.the.event.that.the.tubular.motor.only.runs.for.a.single.rotation.even.when.
the.set.button.is.pressed,.it.is.unlikely.that.the.tubular.motor.is.faulty..Possibly.the.adapter (10).has.slipped.off.of.the.motor.head.
Check and, if necessary, correct the positioning of the adapter (10), see pages 37 and 51.
Finally move the roller shutters down (by briefly actuating the SET button or the external switch).
As soon as the roller shutters are fully closed, the tubular motor switches off automatically. The position of the
roller shutters will be stored as the lower end point.
NOTE
In.the.event.that.the.end.point.configuration.fails,.you.must.reset.the.tubular.motor.to.the.factory.setting.(see.page.50),.in.order.to.repeat.the.process..
To conclude the process, disconnect the tubular motor from the power for a few seconds (e.g. by switching the cord circuit
OFF
setting unit (22) toggle switch back to the central position). Subsequently, the tubular motor is ready for operation.
IMPORTANT
. ◆ If.the."external switch" (h).lead.is.not.used,.then.it.must.be.connected.to.the.neutral conductor (f).(see.fig..k).
. ◆ In.order.to.do.so,.the.tubular.motor.must.be.fully.installed.
. ◆ Never.dismantle.the.mechanical.stopper.from.the.final.roller.shutter.lamella.
. ◆ The.roller.shutter.box.must.be.opened.and.the.set.button.(11).on.the.tubular.motor.
. must.be.freely.accessible.
. ◆ Do.not.allow.the.shutters.to.knock.against.the.mechanical.stops.and.maintain.a. .
. safety.gap.of.2.-.3.cm.
Risk of crushing injuries to the hand when working with the roller
shutter box open.
STOP
Never.reach.into.the.area.of.the.rotating.union.when.the.motor.is.running.
EN