Function.of.the.shutter.length.compensation.system; Function.of.radio.code; Important.assembly.instructions - RADEMACHER RolloTube I-line Funk Small Montageanleitung

i
Function of the shutter length compensation system
The shutter length compensation system is active subsequent to every
automatic learning process for the upper end point. Afterwards, the
tubular motor no longer runs fully against the upper end point in order
to protect the roller shutters and the end points.
For example, seized roller shutters can cause the automatically learned
end points and runs to be changed over a period of time. In order to
compensate for this, the tubular motor periodically runs automatically
to the upper and lower end points (the cycle for this is configured at
the factory).
i
Function of radio code
You.can.control.the.radio.tubular.motor.directly.using.the.radio.code.in.order,.for.example,.
to.be.also.able.to.subsequently.connect.further.DuoFern.devices.to.the.radio.tubular.
motor.after.installation.
Once.the.connection.has.been.successfully.established,.you.can.carry.out.actions.such.as.
setting.the.limit.stops.for.a.radio.tubular.motor.
The radio code can be found on the enclosed label:
Example:
Important assembly instructions
IMPORTANT
. ◆ Check.that.the.voltage./.frequency.on.the.type.plate.corresponds.to.local.mains. .
. conditions.prior.to.installation.
. ◆ All.cables.and.equipment.not.required.for.operation.of.the.equipment.is.to.be.removed. .
. or.deactivated.prior.to.installation.of.the.tubular.motor.
. ◆ Moving.drive.parts.to.be.operated.at.a.height.under.2.5.m.from.the.floor.must.be. .
. protected.
. ◆ If.the.tubular.motor.is.to.be.controlled.with.a.switch.with.a.default.OFF.setting,.then. .
. the.switch.is.to.be.positioned.in.the.line.of.sight.of.the.tubular.motor.and.at.a.height. .
. of.at.least.1.5.m.
. ◆ The.cover.of.the.roller.shutter.box.must.be.freely.accessible.and.removable.
. ◆ Never.dismantle.the.stopper.from.the.final.roller.shutter.lamella..
. Otherwise.the.roller.shutters.may.slip.through.into.the.roller.shutter.box.and.be. .
. damaged.
CAUTION
Installing the tubular motor at an angle can cause the tubular motor or
roller shutters to be damaged. For example, roller shutters wound at
an angle can block the drive and cause damage.
◆ Always ensure that the tubular motors and bearings are mounted
horizontally.
◆ Please ensure that the rotating union (5) and the roller shutters
(17) can move down easily and freely after installation is complete.
. ◆ The.roller.shutters.(17).may.not.run.over.the.bearing,.the.bearing.capsule.(4).or.
. the.drive.head.(12).during.operation.
. ◆ Ensure.that.the.rotating.union.(5).and.the.fastening.springs.(6).of.the.drive.(9).do.
. not.touch..They.may.not.rub.against.the.tubular.motor.(9) during.operation.
36
NOTE
. ◆ The. roller. shutter. compensation. system. operates. automatically. during. normal. .
. operation,.so.that.generally.you.will.not.notice.it.
. ◆ If.the.upper.end.point.is.manually.configured,.then.the.roller.shutter.compensation. .
. system.is.inactive.
NOTE
Time window for activation via the radio code.
After.switching.on.the.power.supply,.the.radio.code.is.active.for.a.maximum.2.hours..Once. .
this. time. has. elapsed,. activation. using. the. radio. code. is. no. longer. possible.. Briefly. .
disconnect.the.environmental.sensor.from.the.mains.to.reactivate.the.time.window.
For automatically actuated awnings:
. ◆ A.minimum.gap.of.0.4.m.to.other.parts.in.the.area.must.be.maintained.when.the. .
. awning.is.fully.extended.
. ◆ Awnings.used.in.an.awning.system.must.maintain.a.minimum.height.of.1.8.m.
Only use tubular motors which correspond to the local conditions in
terms of their power. Incorrectly dimensioned tubular motors can lead
to damage.
. ◆ Incorrectly.dimensioned.drives.and.counter.bearings.can.cause.the.roller.shutter.system.
to.be.damaged..Only.use.original.bearings.supplied.by.the.manufacturer..Third-party.
drives.and.counter.bearings.must.be.selected.in.accordance.with.the.torque.specifica-
tions.of.the.respective.tubular.motors.
Risk of injury in the event of incorrect installation (impact injuries and
contusions).
. ◆ The.motor.can.eject.from.the.drive.bearing.in.the.event.of.incorrect.installation/
fastening..Fasten.the.tubular.motor.with.the.securing.devices.provided.
Mortal danger in the event of operation without configured end points.
. ◆ The.end.points.must.be.configured.in.order.to.ensure.safe.operation..In.order.to.
do.so,.please.refer.to.the.corresponding.chapter.in.this.manual.provided.on.page.44.
EN