Sabo 43-COMPACT Betriebsanleitung Seite 33

IMPORTANT
The engine will only run when the safety control bar on the upper handlebar
section is pressed. The moment the safety grip is released, the latter will return
into its original position by spring force, the engine brake is activated and
engine and cutter bar will come to a standstill within three seconds.
– Press the safety control bar (1) onto the upper handlebar section (2) and hold it
there D .
– Slowly pull the starter cable (3) until resistance is felt, then pull it out rapidly E
– the engine starts to run - , slowly recoil the cable.
NOTE
This engine has a temperature-controlled automatic choke.
The engine runs automatically at an optimum maximum speed, which is required for
a clean cut pattern (engine speed = blade speed).
11 SWITCHING OFF THE ENGINE (FIGURE F )
– Release the safety control bar (1) F .
12 EMERGENCY STOPPING
Release the safety control bar.
– The blade comes to a standstill.
– The engine will stop.
ATTENTION
Before every mowing job, make sure that the engine stop safety control bar is
working perfectly:
– When the safety control bar is released, engine and cutter bar must come
to a standstill within three seconds.
If this is not the case, please consult your nearest authorised workshop.
13 GRASS COLLECTOR
Operation with grass collecting bag
WARNING
When operating the equipment with a grass collecting bag, the bag must be
completely assembled and in technically perfect condition.
IMPORTANT
Ensure that when handling the grass collecting bag, the chute (1)
R1 is not bent.
When using the lawn mower, ensure that the grass collecting bag is emptied in
good time. The TurboSignal on the grass collecting bag shows you the right time
to empty it.
TurboSignal (fill indicator of the grass collecting bag) (Figure J + K )
An indicator is placed on the top of the grass collecting bag to show whether the grass
collecting bag is empty or full:
– When the grass collecting bag is empty and during mowing, the TurboSignal
inflates J .
– If the grass collecting bag is full, the TurboSignal collapses; then immediately
stop mowing and empty the grass collecting bag K .
IMPORTANT
If the collecting bag fabric is very dirty, the TurboSignal does not inflate - you
should clean the fabric immediately. The grass collecting bag will only collect
grass properly if air can pass through it freely.
IMPORTANT
Do not clean the grass collecting bag with hot water!
Emptying the grass collecting bag (figure L )
– Switch off the engine.
– Lift the ejection flap.
– Remove the full grass collecting bag from the mower by the carrying strap – the
ejection flap closes automatically.
– Shake out the grass collecting bag thoroughly, holding it by the carrying strap
and the moulded handle on the bottom.
Operation without grass collecting bag
WARNING
When mowing without grass collecting bag, the ejection flap on the mower
housing must always be closed (flap down).
14 MOWING
Using the machine on slopes
ATTENTION
The mower can be used on banks and slopes with a gradient of up to 46%
(25° angle). Any steeper slopes can lead to engine damage.
For safety reasons, however, we urgently recommend you do not exploit this
theoretical performance potential. Always make sure you have a firm stance.
Walk-behind lawn mowers should never be used for slopes with a gradient in
excess of 26% (15° angle of slope). Stability may be lost!
Checking the oil level
Check oil level before each mowing job Y1. Never let the engine run with too little or
too much oil. Irreparable damages could occur.
Checking operating safety
The lawn mower is fitted with an engine stop device.
Before every mowing job, make sure that the engine stop safety control bar is working
perfectly. When the stop control bar is released, engine and cutter bar must come to
a standstill within three seconds.
After release, the bar must always return to the position shown in the
"Description of components" diagram.
If this is not the case, it must be checked immediately by an authorised workshop.
Risk of injury!
If the stopping time of the blade is longer, stop using the device and take it to an
authorised workshop.
Measuring the stopping time
After starting the combustion engine, the blade rotates and a wind noise can be heard.
The stopping time corresponds to the duration of the wind noise after the combustion
engine has been switched off; it can be measured with a stopwatch.
Machine safety and protective devices must not be manipulated or disabled.
Make sure that all protective devices have been attached properly and are not
damaged.
To avoid any risk, always check the condition and firm seating of the blade before
each mowing job. The blade fastening screw must always be tightened by an
authorised workshop. If the blade screw is tightened excessively or insufficiently, blade
coupling and cutter bar may be damaged or get loose, which can lead to serious
injuries.
A worn or damaged blade must imperatively be replaced. (See chapter "Maintenance
Safety information! of the cutter bar").
For explanation of symbols,
Check fan, blade coupling and fan housing for wear and a tight fit every 10
see the table on page 2
operating hours. Also check device screws and nuts for a firm fit and re-tighten,
if necessary.
Make sure the spark plug connector is fitted tightly. Risk of electric shock.
Never remove the plug connector with the engine running. Risk of electric
shock. Only remove the plug connector if the engine has cooled down. Risk
of burns.
If the mower becomes blocked e.g. by colliding with an obstacle, have an authorised
workshop check whether any parts of the mower are damaged or deformed.
Always have any necessary repairs done by an authorised workshop too.
If the machine starts to vibrate unusually heavily or to make unusual noises,
please have it checked immediately by an authorised workshop.
Time restrictions
In Germany, the time for the operation of lawn mowers is regulated in the "32nd
Ordinance for the Implementation of the Federal Immissions Act (32. BImSch-V)".
In addition, regional restrictions are possible (e.g. to observe the afternoon quiet
hours); related information is available from the competent municipal authority.
Tips on caring for your lawn
Mowing (figure M )
WARNING
Remove all foreign bodies (stones, wood, branches, etc.) from the lawn before
any mowing; however, you should still keep an eye out for objects lying around
while mowing.
You can get an introduction to lawn care from your dealer on request. Information and
instructions for mowing can also be found on the manufacturer's website.
Mulching
Your lawn mower can be equipped with a mulch kit. The corresponding conversion kit
to the mulch system is available from specialist dealers as an accessory (for the order
no. of the conversion kit, see "Original spare parts and accessories").
The mulch kit also includes tips and information on mulching. Information regarding
mulching can also be found on the manufacturer's website.
WARNING
Always have the mower converted to a mulch system by an authorised
specialist workshop. Due to an incorrectly assembled blade coupling or an
excessively or insufficiently tightened blade screw, the cutter bar may become
loose, which can lead to serious injuries.
And if the grass is too high for mulching, the mulching mower can be converted for
mowing with the grass collecting bag with only a few steps.
Conversion to rear discharge mower (figure U2 + S1 )
–
Safety information!
–
For explanation of symbols,
–
see the table on page 2
–
Conversion of the mulching knife system is not necessary! However, under difficult
mowing conditions (e.g. wet grass), the collecting bag filling may be reduced.
So that the device can be used as mulching mower again, the mulch plug must be re-
installed. To do this, remove the grass collecting bag, insert the mulching plug into the
ejection channel and close the ejection flap.
7
Switch off the engine.
Lift the ejection flap.
Remove the mulch plug from the channel U2 .
Hang the grass collecting bag into the provided holder at the mower housing
S1.
EN