Redmond RMC-M800S-E Handbuch Seite 9

To disable the Keep Warm function in advance press and hold the «Start/Reheat»
button until the Keep Warm/Cancel» button LED goes out. To enable the func-
tion, press and hold the «Start/Reheat» button (the «Keep Warm/Cancel» button
LED is lit up solid).
General operating procedure for automatic programmes (except
for the «MULTICOOK» and «REHEAT» programmes)
For information on the «MULTICOOK» and «REHEAT» programmes please
refer to the corresponding sections.
1. Prepare (measure) the ingredients, put them into the bowl. Please make
sure that all the ingredients (water included) are below the maximum fill
mark on the inside of the bowl.
2. Place the bowl inside the appliance. Make sure it makes full contact with
the heating element.
3. Press the multicooker lid until it clicks into place. Plug in the appliance.
4. By pressing the «Menu» button select the required cooking programme,
a corresponding programme indicator and default cooking time will be
displayed. By pressing the «Select product» button, select the type of
product for the «FRY», «STEW», and «STEAM» programmes: a correspond-
ing indicator («MEAT», «FISH», or «VEGETABLES») and default cooking
time will be displayed. You can adjust the cooking time.
5. Enable the «Time Delay» function if necessary.
6. Press and hold the «Start/Reheat» button for a few seconds. The «Start/
Reheat» and «Keep warm/Cancel» buttons LEDs are lit up solid. The cook-
ing cycle starts, the timer starts to countdown.
7. You can disable the Keep warm function in advance during a cooking
cycle by pressing and holding the «Start/Reheat» button (the «Keep warm/
Cancel» button LED is off). To enable the function, press and hold the
«Start/Reheat» button again.
8. When the cooking cycle is completed, an audible signal is heard. After
that, depending on the settings, the appliance switches to either the Keep
Warm mode (the Keep Warm timer will count up) or to the Standby mode.
9. To interrupt the cooking cycle, to cancel the programme or to disable the
«Keep Warm» function, press and hold the «Keep Warm/Cancel» button.
To adjust the cooking time:
1. Having selected the cooking programme, press the «Timer/Time Delay»
button. The «Timer» indicator is displayed, time digits start flashing.
2. Pressing the «+» and «–» buttons, adjust the desired time value. Hold the
corresponding button to scroll through the digits.
3. After adjusting the cooking time (time digits are flashing), proceed to the
next step. To clear time settings, press the «Keep Warm/Cancel» button
and start the adjustment from the beginning.
When adjusting the cooking time manually, please note that adjustment range
and intervals depend on the selected programme. In some programmes count-
down begins only upon your multicooker reaches the set operation tempera-
ture.
«MULTICOOK» programme
The programme is recommended for cooking any meal with your own tem-
perature and time settings. Temperature can be adjusted between 35 and 170°С
with 5°С intervals, and time — between 2 minutes and 15 hours with 1 minute
intervals (for up to 1 hour period of time) or 10 minute intervals (for more than
1 hour period of time).
If the cooking temperature in the «MULTICOOK» programme is below 75°С,
the «Keep Warm» function is not available.
1. Follow steps 1-3 of the «General operating procedure for automatic pro-
grammes» section.
2. Press the «Multicook/°С» button, the cooking temperature will be displayed
(default temperature is 100°С). Press the «–» and «+» buttons to adjust
the cooking temperature.
3. In 2-3 seconds after temperature is adjusted, the «Timer» indicator and
flashing time digits will be displayed (default time is 30 minutes).
If you failed to adjust the desired cooking temperature, press and hold the
«Keep Warm/Cancel» button until an audible signal is heard, then start the
adjustment from the beginning.
4. Press the «–» and «+» buttons to adjust the cooking time. Press and hold
the corresponding button to scroll through the digits.
5. To set the time of delay (if necessary), press and hold the «Timer/Time
delay» button. The «Time delay» indicator and the remaining cooking time
(time delay included) are displayed. Adjust the time value by pressing the
«–» and «+» buttons. Press and hold the corresponding button to scroll
through the digits.
6. Then follow steps 6-8 of the «General operating procedure for automatic
programmes» section.
«RICE/GRAIN» programme
The programme is recommended for cooking rice and other types of grain.
Default cooking time is 35 minutes. You can manually adjust the cooking time
from 5 minutes to 4 hours in 1 minute intervals.
«SLOW COOK» programme
The programme is recommended for cooking fore shank, meat jelly or fish and
other dishes, that require slow cooking. Default cooking time is 2 hours and 30
minutes. You can manually adjust the cooking time from 10 minutes to 12 hours
in 10 min intervals.
«PILAF» programme
The programme is recommended for cooking beef pilaf, pilaf with fish or veg-
etables. Default cooking time is 1 hour. You can manually adjust the cooking
time from 10 minutes to 2 hours in 5 min intervals.
«FRY» programme
The programme is recommended for frying meat, fish, and vegetables. Default
cooking time depends on selected programme (use the «Select product» button):
«MEAT» — 15 minutes, «FISH» — 12 minutes, «VEGETABLES» — 18 minutes. You
can manually adjust the cooking time from 5 minutes to 2 hours in 1 minute
intervals.
"Time Delay" function is not applicable for this programme.
«STEW» programme
The programme is recommended for stewing meat, fish, vegetables, meat jelly
or fish and other dishes, that require long cooking. Default cooking time depends
on the selected programme (use «Select product» button): «MEAT» — 1 hour,
«FISH» — 35 minutes, «VEGETABLES» — 40 minutes. You can manually adjust
the cooking time from 10 minutes to 12 hours in 5 min intervals.
«PASTA» programme
The programme is recommended for cooking different types of pasta, boiling
eggs and sausages. Default cooking time is 8 minutes. You can manually adjust
the cooking time from 2 minutes to 1 hour in 1 min intervals.
"Time Delay" function is not applicable for this programme.
Fill the bowl with water. Please make sure that water level is below the maxi-
mum mark on the inside of the bowl. Follow steps 2-7 of the "General operating
procedure for automatic programmes" section. After water comes to a boil, an
audible signal is heard. Open the lid carefully and add pasta to the boiling
water, press the lid until it clicks into place. Press the «Start/Reheat» button.
The cooking cycle starts, the programme countdown begins. Follow steps 8-9
of the "General operating procedure for automatic programmes" section.
When cooking meals that may foam, open the lid a few minutes after you add
the ingredients into water to prevent foam from boiling over.
RMC-M800S-E
«VACUUM» programme
The programme allows cooking vacuum sealed food. Default cooking time is 2
hours and 30 minutes. You can manually adjust the cooking time from 5 minutes
to 12 hours in 10 min interval.
«SOUP» programme
The programme is recommended for cooking different types of soups, broths,
and compotes. Default cooking time is 1 hour. You can manually adjust the
cooking time from 10 minutes to 8 hours in 5 min interval.
«YOGURT» programme
The programme is recommended for making yogurts and proofing dough. Default
cooking time is 8 hours. You can manually adjust the cooking time from 10
minutes to 12 hour in 5 min interval.
The "Keep warm" function is not available.
«BAKE» programme
The programme is recommended for baking pies, biscuits, and cakes. Default
cooking time is 45 minutes. You can manually adjust the cooking time from 10
minutes to 8 hours in 5 min interval.
When baking bread, it is recommended to deactivate "Keep warm" function at
all cooking stages.
«STEAM» programme
The programme is recommended for steaming meat, fish, vegetables, baby food.
Default cooking time depends on selected programme (use the «Select product»
button): «MEAT» — 40 minutes, «FISH» — 25 minutes, «VEGETABLES» — 30 min-
utes. You can manually adjust the cooking time from 5 minutes to 2 hours in 5
min interval.
Use the adjustable capacity basket (included in the set) for the programme:
1. Fill the bowl with 600-1000 ml of water.
2. Insert the inner bowl of the steam basket in the outer rim, so that its
ledges fit the rim cavities. There are two types of cavities inside the
rim – for height and capacity adjustment of the steam basket.
3. Place the basket inside the bowl.
4. Measure and prepare ingredients according to the recipe directions and
distribute them evenly inside the basket.
5. Follow steps 2-9 of the "General operating procedure for automatic pro-
grammes" section.
«COOK/BEANS» programme
The programme is recommended for cooking vegetables and beans. Default
cooking time is 40 minutes. You can manually adjust the cooking time from 5
minutes to 8 hours in 5 min intervals.
«REHEAT» programme
Your multicooker can reheat food. The programme reheats food up to 70-75°C
and keep it hot for up to 24 hours. For this programme direct time counting is
provided. Reheating can be canceled manually.
The "Time delay" function is not available.
1. Fill the bowl with food and place it into the appliance. Make sure the bowl
makes full contact with heating element. Press the lid until it clicks. Plug
the appliance.
2. Press and hold the «Keep Warm/Cancel» button until the sound signal is
heard. The button LED lights on, the programme starts, and the reheating
timer begins counting up. When the programme is completed, a sound
signal is heard. The appliance will switch to the standby mode.
3. To cancel reheating, press and hold the «Keep Warm/Cancel» button until
the sound signal is heard. The button LED is off.
The «REHEAT» programme can maintain food hot for up to 24 hours, how-
ever it is not recommended use this programme for more than 2-3 hours as
this may affect food flavour.
GBR
9