Dust/Chip Extraction - Bosch GTS 10 XC Professional Originalbetriebsanleitung

34 | English
Mounting the Insert Plate (see figure b)
– Hook insert plate 31 into the rear insert-plate notches 45
of the tool basin.
– Guide the insert plate down.
– Press on the insert plate until it engages at the front in the
tool basin.
The front side of the insert plate 31 must be flush with or
somewhat lower than the saw table; the rear side must be
flush with or somewhat above the saw table. (also see "Ad-
justing the Level of the Insert Plate", page 39)
Mounting the Blade Guard* (see figure c)
* depending on country version
– Turn crank 20 clockwise to the stop, so that the saw blade
32 is in the highest possible position above the saw table.
– Insert the blade guard 5.x into the recess in riving knife 7.
– Tighten the clamping lever 46.1.
or
Tighten clamping screw 46.2 with hex key 37.
– Adjust the blade guard according to the workpiece height.
When sawing, the blade guard must always face lightly
against the workpiece.
Note: Clamping lever 46.1 is indexed (adjustable), allowing it
to be set to an ergonomically favourable or space-saving posi-
tion.
With the clamping lever tightened, pull its lever away from the
blade guard, turn it to the desired position and allow it to en-
gage again.
Mounting the Table Extension (see figure d)
For assembly, use the fastening kit for "table extension" 43.
(2 fastening screws, 2 washers, 1 open-end spanner)
– Bolt the table extension 10 with the guide rods 24.
When doing this, the recesses in the table extension must
face upward.
Mounting the Parallel Guide (see figure e)
The parallel guide 8 can be positioned either left or right from
the saw blade.
– Loosen clamping handle 47 of parallel guide 8.
This releases V-guide 48.
– Firstly, mount the parallel guide via the V-guide in guide
groove 30 of the saw table. Now, position the parallel
guide into the front guide groove 35 of the saw table.
The parallel guide can now be moved to any position.
– To lock the parallel guide, press the clamping handle 47
down.
Mounting the Auxiliary Parallel Guide (see figure f)
When sawing narrow workpieces and bevel angles, the
auxiliary parallel guide 49 must be mounted to parallel guide
8.
The auxiliary parallel guide can be mounted left or right from
parallel guide 8, as required.
For assembly, use the "auxiliary parallel guide" fastening kit
39. (3 fastening screws, 3 washers, 3 wing nuts)
– Insert the fastening screws through the lateral holes in the
parallel guide 8.
1 609 92A 15S | (29.1.15)
The heads of the screws serve as a guide for the auxiliary
parallel guide.
– Move the auxiliary parallel guide 49 over the heads of the
fastening screws.
– Mount the washers to the fastening screws and tighten
them with the wing nuts.
Mounting the Angle Stop (see figures g1–g2)
– Insert the guide rail 50 of the angle stop 3 into one of the
guide grooves 9 of the saw table intended for this purpose.
Note: In the lefthand guide groove, the position of the angle
stop can be affixed on the sliding table by tightening the
knurled screw 51.
For improved placement of long workpieces, the angle stop
can be extended with profile rail 34.
– If required, mount the profile rail to the angle stop with fas-
tening kit 52.
Stationary or Flexible Mounting
 To ensure safe handling, the machine must be mounted
on a level and stable surface (e. g., workbench) prior to
using.
Mounting to a Working Surface (see figure h)
– Fasten the power tool with suitable screw fasteners to the
working surface. The mounting holes 16 serve for this pur-
pose.
Mounting to a Bosch Saw Stand (see figure i)
With the height-adjustable legs, Bosch saw stands (e. g.
GTA 60 W, GTA 6000) provide firm support for the power
tool on any surface.
 Read all safety warnings and instructions included with
the worktable. Failure to observe safety warnings and in-
structions can lead to electrical shock, fire and/or cause
serious injuries.
 Assemble the worktable properly before mounting the
power tool. Perfect assembly is important in order to pre-
vent the risk of collapsing.
– Mount the power tool in transport position on the saw
stand.

Dust/Chip Extraction

Dusts from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dusts can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dusts, such as oak or beech dust, are considered as
carcinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be worked by specialists.
– Always use dust extraction.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the mate-
rials to be worked.
The dust/chip extraction can be blocked by dust, chips or
workpiece fragments.
Bosch Power Tools