Herunterladen Diese Seite drucken

Scheppach HSM3500 Originalbetriebsanleitung Seite 33

Steintrennmaschine
Vorschau ausblenden Andere Handbücher für HSM3500:

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
• Make sure that the switch is OFF before inserting
the plug into the socket.
• Make sure that the machine has been cleaned and
lubricated properly.
• Before commissioning, check the machine for dam-
aged parts and determine whether these parts func-
tion properly and fulfil their intended function.
• Check the alignment of all moving parts, all fixing
parts, and any other conditions which may impede
proper operation. Any damaged part must be re-
paired or replaced by a specialist immediately.
• Do not use the machine if a switch cannot be
switched on and off properly.
9.
Operation
• Place the machine on a level, non-slip floor.
• Check that the voltage on the data plate matches
the existing voltage, and only then connect the plug
to the mains.
• Before switching on, the cutting wheel must be able
to rotate freely.
Attention: The cutting wheel must always be cooled
with water.
Attention: Cutting wheel runs on.
Do not brake the cutting wheel by applying lateral
pressure.
• During normal use, the motor housing may become
hot.
• Do not force the machine or an accessory to do the
work of a larger industrial machine. It does a better
job with the performance it was designed for.
• Make all machine settings with the machine
switched off.
• Never leave the machine unattended when it is run-
ning.
• When shutting down, only leave the machine after
it has come to a complete standstill.
• Always switch the machine off before unplugging
the mains plug.
• Always unplug the mains plug. Never pull the plug
out of the socket using the cable.
• Do not use a cutting wheel that does not match the
specified sizes.
• Never carry the machine by the cable.
If you are not sure whether working conditions are safe
or unsafe, do not work with the machine.
10. Assembly
10.1 Assembly (Fig. 4 - 10)
Your machine is not completely assembled for pack-
aging reasons.
At least two people are required to construct the
device!
1.
Remove the machine from the packaging and
place carefully to one side on the ground.
2.
First, fold out the foot (11) on the side without
transport rollers until it reaches the end stop, until
the screw engages in the elongated hole as shown
in Fig. 7. Make sure that the foot is locked in
place and does not fold up again!
3.
Repeat the process for the second foot (Fig. 8).
4.
Place the machine on the feet.
5.
Use the cable ties provided to fix the water pipe hose
and the cable to the device housing. (Fig. 10.2)
6.
Insert the water pump (18) into the water pan hold-
er and insert the sealing plug(s) into the water tank
drain (8). (Fig. 9, 10)
7.
Fill the pan with water so that the pump (18) is al-
ways covered with water (even during operation).
Attention!
The water pump may never run dry. It must always be
covered with water during operation.
10.2 Mounting the roll slide (Fig. 11)
1.
Place the roll slide (cutting table) (6) on the roll
table guide rail (9); in the process, the frame (a)
of the two right guide rollers covers the guide rail.
Simply place the two left guide rollers on the guide
rail.
2.
When you are standing in front of the stone cutting
machine, the scale must face towards you. The
90° cutting wheel gap is to the left in the roll slide
(6), the 45° cutting wheel gap is to the right.
3.
The cutting table must roll easily. Make sure that
all four rollers are on the guide rail (9).
10.3 Mounting the lever screw for the cutting head
pivoting device (Fig. 12)
1.
Remove the hexagon screw with a 30 mm
open-ended spanner.
2.
Fit the lever screw (d) of the cutting head pivoting
device on the thread and tighten it.
10.4 Mounting the rip fence (Fig. 13)
1.
Place the rip fence (13) on the stop rail with scale
(7) on the roll slide (6).
www.scheppach.com
GB | 33

Werbung

loading

Diese Anleitung auch für:

590670990159067089969