Scheppach HSM3500 Originalbetriebsanleitung Seite 29

6. Do not overload your tools
They work better and more safely in the specified
output range.
7. Use the correct tool
Do not use tools that are too weak or attachments
for tough tasks. Do not use tools for purposes and
work for which they are not intended; for example,
do not use a hand-held circular saw to fell trees or
cut branches.
8. Wear suitable work clothing
Do not wear loose clothing or jewellery. They can
be caught by moving parts. Rubber gloves and an-
ti-slip footwear are recommended when working
outdoors. Tie long hair back in a hair net.
9. Wear safety goggles
Use a respiratory mask when working with dust.
10. Do not misuse the cable
Do not carry the tool by the cable and do not use it
to pull the connector out of the socket. Protect the
cable from heat, oil and sharp edges.
11. Secure the workpiece
Use the clamping devices or a bench vice to hold
the workpiece in place. It is thus held more secure-
ly than with your hand and allows the machine to
be operated with both hands.
12. Do not overstretch your standing area
Avoid an abnormal posture. Make sure that you have
secure footing and always maintain your balance.
13. Take care of your tools
Keep your tools sharp and clean so that you can
work well and safely. Follow the maintenance in-
structions and the instructions for tool changes.
Check the connector and the cable regularly and
have it replaced by a recognised specialist when
damaged. Check extension cables regularly and
replace them when damaged. Keep the handle dry
and free of oil and grease.
14. Pull out the mains plug
When not in use, before maintenance and when
changing tools, such as saw blade, drill bit and ma-
chine tools of all kinds.
15. Do not leave a tool key inserted
Before switching on, make sure that keys and ad-
justing tools are removed.
16. Avoid inadvertent starting
Do not carry tools connected to the mains with your
finger on the switch. Make sure that the switch is
switched off when connecting to the mains.
17. Extension cable outdoors
Only use approved and appropriately identified ex-
tension cables for use outdoors.
18. Always remain attentive
Observe your work. Proceed sensibly. Do not use
the tool if you are distracted.
19. Check your device for damage
Carefully inspect protective devices or other parts
with minor damage to ensure that they function
correctly and as intended prior to continued use
of the tool. Check whether the moving parts func-
tion properly, that they do not jam or whether parts
are damaged. All parts must be correctly fitted
and all conditions must be fulfilled to ensure fault-
free operation of the device. Damaged protective
devices and parts should be repaired properly or
replaced by a customer service workshop unless
otherwise specified in the operating manual. Dam-
aged switches must be replaced at a customer
service workshop. Do not use any tools on which
the switch cannot be switched on and off.
20. Attention!
For your own safety, only use accessories and
additional equipment that are indicated in the op-
erating manual or have been recommended or
indicated by the tool manufacturer. Use of other
tool attachments or accessories that those rec-
ommended in the operating manual or in the cat-
alogue could represent a personal danger to you.
21. Only have repairs carried out by a qualified elec-
trician
This power tool conforms to the applicable safety
regulations. Repairs may only be carried out by a
qualified electrician, otherwise accidents may oc-
cur for the operator.
22. Connect the dust extraction device
If there are fixtures for connecting dust vacuum de-
vices, make sure that they are connected and used.
m WARNING! This power tool generates an elec-
tromagnetic field during operation. This field can im-
pair active or passive medical implants under certain
circumstances. In order to prevent the risk of serious
or deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operating
the power tool.
Store the safety instructions safely.
SPECIAL SAFETY INSTRUCTIONS
Attention! This stone and tile cutter is designed for wet
cutting. The mesh may be used with a non-segmented
diamond cutting wheel.
www.scheppach.com GB | 29