The Functions Of The Breadmaker - Unold BACKMEISTER TOP EDITION 68415 Bedienungsanleitung

Attention: Do not interrupt the programme for more than
5 minutes. In case of longer interruptions the rising of the
dough may be disturbed.
As long as the PAUSE function is activated (blinking dis-
play) the START/STOPP button is without function and the
programme cannot be STOPPped completely.
LIGHT
The interior of the breadmaker TOP
EDITION is fitted with a lighting,
which allows to follow the actual
state of the programme without ope-
ning the lid. Just press the button
LICHT and the light turns on. To
switch off the light just press the
button again. After 1 minute the
light is automatically switched off.
EIGENPROGRAMM/USER PROGRAM
In addition to the other numerous programs provided by
the BACKMEISTER you can also program your own USER
®
PROGRAM. You can change the basic time and program
phase settings as programmed at the factory or leave out
various program phases. This allows you to develop your
own individual program for baking bread or preparing
dough. Below you will find a sample recipe.
First you should become familiar with the following infor-
mation on the basic programming and use of the USER
PROGRAM.
USER PROGRAM
The program features the following options
Browning
Timer
Loaf size I and II
The default program is the same as for the BASIC program.
Phase Preset
Total time 3:00 hours
Knead 1 10 minutes

THE FUNCTIONS OF THE BREADMAKER

Alarm function
The alarm sounds:
ƒ whenever the MENU or ZEIT/time buttons are pressed,
ƒ when pressing the programme buttons to confirm
each step,
ƒ during the second kneading process, to remind you
to add seeds, fruit, nuts or other ingredients. Please
note that this function cannot be deactivated, e.g. in
the time preset function,
ƒ at the end of the baking process, the appliance beeps
often during the keep-warm phase,
ƒ at the end of the keep-warm phase several beeps
remind you that the appliance is now switched off
and the bread has to be taken out of the bread pan.
Please note that this function cannot be deactivated,
e.g. in the time preset function.
38
programmable
programmable
not programmable
Programmable time frame
6-14 minutes
Rise 1 20 minutes
Knead 2 15 minutes
Rise 2 25 minutes
Rise 3 45 minutes
Bake 45 minutes
Keep warm 60 minutes
The times can be programmed as shown in the table.
Proceed as follows:
Select the USER PROGRAM with the Menu button.
Select the desired phase with the ABSCHNITT button.
Knead 1 and the programmed time 0:10 for this phase
appear on the display.
The time can be changed by means of the ZEITWAHL but-
ton. Press it repeatedly until the desired time appears on
the display (past OFF, if necessary).
Confirm the change with the ABSCHNITT button. Press
this button again and the next program phase and the pro-
grammed time will appear on the display: Rise 1 = and
0:20.
If the maximum programmable time for the respective pro-
gram phase is exceeded by pressing the ZEITWAHL button,
O will appear on the display if this is possible according
to the above table. This phase is then skipped during the
program.
Every programmed setting must be confirmed by pressing
the ABSCHNITT button, so you can continue programming
the next program phase.
Once you have programmed all phases to suit your pre-
ferences, conclude the programming by pressing the AB-
SCHNITT button and then the START/STOPP button. The
programmed time for the user program appears on the dis-
play. The program then starts either immediately or after
the time set via the timer function.
ƒ The alarm function cannot be inactivated.
Repeat function after power outage
Should the electricity supply been cut off during the ope-
ration of the Breadmaker, the appliance will re-start, on
re-instatement of the supply, automatically from the point
arrived at when the cut-off occurred as long as the inter-
ruption is not longer than 2 minutes. If the interruption in
the electricity supply lasts more than 2 minutes and the
display shows the basic setting, the Breadmaker must be
re-started. This is only practical if the dough was not fur-
ther than the kneading phase when the break occurred. If
the program was already in the last rising cycle when the
power broke down and the interruption lasts over a longer
time, the dough cannot be saved and the program has to
be started again.
Copyright UNOLD AG | www.unold.de
20-60 minutes
5-20 minutes
5-120 minutes
0-120 minutes
0-80 minutes
0-60 minutes