Inhaltsverzeichnis
Werbung
System Exclusive Data Format
See ftp://ftp.waldorf-gmbh.de
/pub/waldorf/microwave2/doc/mw2_sysex.txt
------------------------------------------------------
Waldorf Microwave 2 System Exclusive Specifications,
Software release 2.28
Changes from 2.01 to 2.09 marked with !!
Changes from 2.09 to 2.16 marked with !!!
If you find any documemtation bug herein, please mail
it to
bugs@waldorf-gmbh.de
1. General
******************************************************
**************
Sys-Ex dumps and requests will always be in the
following form:
F0h IDW DEV IDM LOC --------Data--------- CHKSUM F7h
where
h
: Hex
IDW
: Waldorf MIDI ID = 3Eh
IDE
: Equipment ID = 0Eh for MicroWave 2
DEV
: Device number, 00h to 7Eh, 7Fh = broadcast
IDM
: Message ID
LOC
: Location
Data
: whatever data bytes, 00h to 7Fh
CHKSUM
: Sum of all databytes truncated to 7 bits.
The addition is done in 8 bit format, the
result is masked to 7 bits (00h to 7Fh). A
checksum of 7Fh is
always accepted as valid.
IMPORTANT: the MIDI status-bytes as well
as the ID's are not used for computing the
checksum. If there are no data-bytes in
the message (simple request), the checksum
will always be 00h.
******************************************************
1.1 Message IDs (IDM)
******************************************************
Message IDs (IDM) are organized in a matrix where the
row defines the data type and the column identifies
the type of dump. The data type is coded in the four
least significant bits of the IDM. Following data
types are currently defined:
Label
Value
Description
--------------------------------------------------
SNDx
x0h
Sound data type
MULx
x1h
Multi data type
WAVx
x2h
Wave data type
WCTx
x3h
Wave control table data type
GLBx
x4h
Global Parameters
DISx
x5h
Display
RMTx
x6h
Remote control
MODx
x7h
Mode (sound/Multimode)
INFx
x8h
Information
--------------------------------------------------
The dump type is coded in the upper three bits of IDM,
note that bit seven cannot be used. Following dump
types are currently defined:
Label
Value
Description
--------------------------------------------------
xxxR
0xh
Request
xxxD
1xh
Dump
xxxP
2xh
Parameter Change
xxxS
3xh
Store command
xxxL
4xh
Recall Command
xxxC
5xh
Compare command
--------------------------------------------------
Not all combinations of dump types and data types are
currently supported, only those given below:
Request (xxxR = 0x)
106
| Dump (xxxD = 1x)
|
| Parameter Change (xxxP = 2x)
|
|
| Store (xxxS = 3x)
|
|
|
| Recall (xxxL = 4x)
|
|
|
|
| Compare (xxxC = 5x)
|
|
|
|
|
|
Data Type
--------------------------------------------------
00 10 20
SNDx x0
01 11
MULX x1
02 12
WAVx x2
03 13
WCTx x3
04 14 24
GLBx x4
05 15 25
45
DISx x5
26
RMTx x6
07 17
MODx x7
--------------------------------------------------
So follwing valid IDM exist:
Label
Value
Description
--------------------------------------------------
SNDR
00h
Sound Request
SNDD
10h
Sound Dump
SNDP
20h
Sound Parameter Change
MULR
01h
Multi Request
MULD
11h
Multi Dump
WAVR
02h
Wave
Request
WAVD
12h
Wave
Dump
WCTR
03h
Wave
Control Table Request
WCTD
13h
Wave
Control Table Dump
GLBR
14h
Global Parameter Request
GLBD
14h
Global Parameter Dump
DISR
05h
Display Request
DISD
15h
Display Dump
DISP
25h
Display Parameter Change
DISL
45h
Display Recall
RMTD
26h
Remote Dump
MODR
07h
Mode Request
MODD
17h
Mode Dump
--------------------------------------------------
******************************************************
2. Details
2.11 SNDR
******************************************************
SNDR
00h
Sound Request
Upon reception of a valid sound request the MW2 will
dump the selected Sound(s). The location is given in
two bytes with following conventions:
BB NN
Location
------------------------------------------------
00 00 .. 00 7F
Locations A001..A128
01 00 .. 01 7F
Locations B001..B128
10 00
All Sounds
20 00
Sound Mode Edit Buffer
30 00 .. 30 07
Multi Instrument Edit Buffers
------------------------------------------------
So the full format of a SNDR Dump is:
Index
Label
Value
------------------------------------------------------
0
EXC
F0h
1
IDW
3Eh
GmbH ID
2
IDE
0Eh
3
DEV
4
IDM
00h
5
BB
see Text
6
NN
see Text
7
XSUM
(BB+NN)&7Fh
8
EOX
F7h
------------------------------------------------------
******************************************************
User's Manual MicroWave II • MicroWave XT • XTk
Sound
Multi
Wave
Wavetable
Global Parameters
Display
Button / Dial remote
Mode !!!
Description
Marks Start of SysEx
Waldorf Electronics
Microwave 2 ID
Device ID
here SNDR (Sound
request)
Location
Location
Checksum
End of SysEx
Werbung
Inhaltsverzeichnis
