Cleaning And Maintenance - Scheppach Pwp32 Originalbetriebsanleitung

10.2 Switch off the engine (Fig. 8, 10)
Note:
Allow the product to run for a short time (approx. 30 sec-
onds) switching it off so that the engine can cool down.
1. To switch off the engine, turn the on/off switch (10) to
the "OFF" position.
2. Set the fuel valve (12) to "OFF".
3. Disconnect the spark plug connector (5) from the
spark plug (5a) to prevent the engine from restarting.
10.3 After end of work (Fig. 1)
1. Remove the pressure line*.
2. Remove the suction line*.
3. Unscrew the water drain plug (15) and let the water
flow out of the pump chamber.
4. Refit the water drain plug (15).
* = may not be included in the scope of delivery!

11 Cleaning and maintenance

WARNING
Have maintenance and repair tasks that are
not described in this operating manual, car-
ried out by a specialist workshop. Use only
original spare parts.
WARNING
Improper maintenance or cleaning work can
cause injuries!
WARNING
The product may start unexpectedly and cause inju-
ries and burns during cleaning, repair and mainte-
nance work.
– Switch the product off.
– Remove the spark plug connector from the spark
plug.
– Allow the product to cool.
11.1 Cleaning
• Only carry out cleaning and maintenance work to the
extent specified in this operating manual. Further work
must be carried out by qualified specialists.
• Keep protective devices, air vents and the motor
housing as free of dust and dirt as possible. Rub the
product clean with a clean cloth* or blow it off with
compressed air* at low pressure. We recommend that
you clean the product directly after every use.
• Clean the product at regular intervals using a damp
cloth* and a little soft soap. Do not use any cleaning
products or solvents; they could attack the plastic
parts of the product. Make sure that no water can pen-
etrate the product interior.
* = may not be included in the scope of delivery!
26 | GB
11.1.1
Note:
The petrol filter is a fuel filter insert cup, which is located
directly under the fuel cap and filters all the fuel that is
filled in.
1. Unscrew the fuel filler cap (3).
2. Remove the fuel filter insert (2a). Clean it in a non-
flammable solvent or a solvent with a high flash point.
3. Reinsert the fuel filter insert (2a).
4. Retighten the fuel filler cap (3).
11.2 Maintenance (Fig. 1, 2)
Tool required:
• Spark plug wrench (21)
• Screwdriver (22)
• Oil pump*
• Collection bucket*
• Fuel extraction pump*
• Open-ended spanner, size 10 mm*
• Wire brush*
• Feeler gauge*
* = may not be included in the scope of delivery!
11.2.1
WARNING
Health hazard!
Inhalation of fuel / lubricating oil vapours and exhaust
gases can cause serious damage to health, uncon-
sciousness and in extreme cases death.
– Do not breathe fuel / lubricating oil vapours and ex-
haust gases.
– Operate the product outdoors only.
ATTENTION
Product damage!
Using the product without or with too little engine and
gear oil can result in engine damage.
– Fill with fuel and oil before commissioning. The
product is supplied without engine and gearbox oil.
– Only use SAE 10W-30 or SAE 10W-40 engine oil.
ATTENTION
Environmental damage!
Spilled oil can pollute the environment permanently.
The liquid is highly toxic and can quickly lead to water
pollution.
– Fill/empty oil only on level, paved surfaces.
– Use a filling nozzle or funnel.
– Collect drained oil in a suitable container.
– Wipe up spilled oil carefully immediately and dis-
pose of the cloth according to local regulations.
– Dispose of oil as per local regulations.
www.scheppach.com
Cleaning the fuel filter insert (2a)
(Fig. 4)
Checking the oil level (Fig. 3)