Scheppach HS730 Originalbetriebsanleitung Seite 24

• Personnel working on the machine must not be dis-
tracted.
• Observe the direction of rotation of the engine and
saw blade. Only use saw blades whose maximum per-
missible speed is not less than the maximum spindle
speed of the circular saw and the material to be cut.
• Under no circumstances should the saw blades be
braked by pushing against the side after switching
off the drive.
• Only install saw blades that are well sharpened, free
of cracks and not deformed.
• Only use saw blades recommended by the manufac-
turer and which comply with EN 847-1.
• Faulty saw blades must be replaced immediately.
• Do not use saw blades that do not correspond to the
characteristics specified in these usage instructions.
• Safety equipment on the machine must not be disas-
sembled or made unusable.
• Replace worn table or swivel frame insert.
• Working position always to the side of the saw blade.
• Do not load the machine so much that it comes to
a standstill.
• Make sure that cut-off pieces of wood are not caught
by the sprocket of the saw blade and flung away.
• Never remove loose fragments, chips or jammed
wood pieces from the running saw blade.
• To rectify faults or remove jammed pieces of wood,
switch the machine off. - Pull out the mains plug -
• If the sawing gap has increased due to wear, replace
the swivel frame or table inlay. Switch off the ma-
chine and pull out the mains plug.
• Only carry out modifications, adjustments, meas-
urements and cleaning work when the engine is
switched off.
• Before switching on, make sure that keys and adjust-
ing tools are removed.
• Switch off the engine and pull out the mains plug
when leaving the work station.
• All protective and safety equipment must be reas-
sembled immediately after repair or when mainte-
nance is completed.
• The safety, operating and maintenance information
of the manufacturer, as well as the dimensions spec-
ified in the technical data, must be observed.
• The relevant accident prevention regulations and
the other generally accepted safety rules must be
observed.
• Make sure that you have secure footing and always
maintain your balance.
• Check the electric tool for potential damage!
24 | GB
• Protective devices or other parts with minor damage
must be carefully inspected to ensure that they func-
tion correctly and as intended prior to continued use
of the tool.
• Check whether the moving parts function faultlessly
and do not jam or whether parts are damaged. All parts
must be correctly mounted and all conditions must be
fulfilled to ensure fault-free operation of the tool.
• Damaged protective devices and parts must be
repaired properly or replaced by a recognised spe-
cialist workshop unless otherwise specified in the
usage instructions.
• This tool conforms to the applicable safety regula-
tions. Repairs may only be performed by a special-
ist using original spare parts. Otherwise accidents
could occur.
• If necessary, wear suitable personal protective
equipment. This could include:
- Hearing protection to prevent the risk of develop-
ing hearing loss;
- Respiratory protection to avoid the risk of inhaling
damaging dust.
• Wear gloves when handling saw blades and rough
materials. Saw blades must be carried in a container
whenever practical.
• Wear personal protective equipment and always
safety goggles.
• The operator must be informed about the conditions
that affect the noise levels (e.g. saw blades designed
to reduce noise, care of saw blade and machine).
• Faults in the machine, including the guards and the
saw blade, must be reported to the person responsi-
ble for safety as soon as they are discovered.
• When transporting the machine, use only the trans-
port devices and never use the guards for handling
and transport.
• All operators must be adequately trained in the use,
setting and operation of the machine.
• Do not saw any material to be cut that contain for-
eign bodies such as wires, cables or cords.
• Only use sharp saw blades.
• The machine must be on a horizontal, level floor dur-
ing operation and the floor around the machine must
be level, well maintained and free of waste such as
chips and cut-off workpieces.
Warning!
This power tool generates an electromagnetic field
during operation. This field can impair active or pas-
sive medical implants under certain circumstances.
www.scheppach.com