Yamaha RD250 Ergänzung Zur Wartungsanleitung Seite 40

Items
Tightening torque:
Front wheel axle (M 14 P1.5)
Front axle holder (M8 P1.25)
Rear wheel axle (M 14 P1.5)
Brake:
Disc brake, front/rear
Type
DISC size (outside dia. x thickness)
Disc wear limit
Disc pad size
Pad wear limit
Master cylinder inside dia.,
front/rear
Caliper cylinder inside dia.,
front/rear
Brake fluid type
Tightening torque
Brake disc and hud, front/rear
(M8 P1.25)
Caliper bracket and front fork
(MIO P1.25)
Caliper and caliper bracket,
front/rear (M8 P1.25)
Caliper and brake hose, front/rear
(MIO P1.25)
Master cylinder and brake hose,
front/rear (MIO Pl .25)
Caliper and bleed screw, front/rear
(M8 P1.25)
D. Electrical
Items
Vol tage
Ignition system:
C.D.I
Model/Manufacturer
Pulser coil resistance
(White/Red-Black)
Charge coil resistance
High speed (Red-Brown)
Low speed (Brown-Black)
RD400
RD250
m-kg (80 ft-lb)
II
1 m-kg ( 7 ft-lb)
m-kg (80 ft-lb)
II
Hydraulic disc type
(front/rear)
267 x 7 mm
(10.5 x 0.03 in)
6.5 mm (0.26 in)
11 mm (0.43 in)
6.5 mm (0.26 in)
15.87 mm (0.62 in)
42.85 mm (l .69 in)
DOT
2.0 m-kg (14.5 ft-lb)
3.5 m-kg (25 ft-lb)
2.5 m-kg (18 ft-lb)
2.5 m-kg (18 ft-lb)
2.5 m-kg (18 ft-lb)
0.6 m-kg (4.5 ft-lb)
RD400
RD250
12V
032000-054/
NIPPON DENSO
87 Q at 200C
(680 F)
5.1 at 200C
(680 F)
271 200C
(680 F)
I tems
Tightening torque:
Rotor (12 mm)
Stator (6 mm)
Ignition timing.
Ignition coil:
Model/manufacturer
Spark gap
Primary winding resistance
Secondary winding resistance
Spark plug:
Type
Spark plug gap
C.D.I. unit:
Model/Manufacturer
Charging system:
A.C. magneto:
Model/Manufacturer
Rotor puller thread size
Output
Starter coil resistance
White-white (5P-5P)
(4p-5p)
Rectifier with regulator:
Model/Manufacturer
(Rectifier)
Ty pe
Capacity
Withstand voltage
(Regulator)
Type
Regu lating voltage
Allowable amperage
Battery :
Model /Manu factu rer
Charging rate
Specific gravity
RD400
RD250
8.0 m-kg (58 ft-lb)
0.3 m-kg (2 ft-lb)
B.T.D.C. 1.6 mm B.T.D.C. 2.0 mm
(0.08 in)
(0.06 in)
0297004740/
NIPPON DENSO
mm (0.24 in)/
500 r/min>
0.33 0 at 200 C
(680 F)
3.5 ko at 200C
(680 F)
B-9ES (N.G.K.)
B-8ES (N.G.K.) (G)
0.7 — 0.8 mm
(0.028 — 0.031 in)
070000-0380/
NIPPON DENSO
032000-054/
NIPPON DENSO
M27 x P1 .O
14v-13.5A/500 r/min
0.496 0 at 200C
(680 F)
0.45 at 200C
(680 F)
SH235/SHlNDENGEN
I.C. type, three phase
full wave
15A
200V
I.C. type
14.5 ±O.5V
15A
12V. 5.5AH/F.B. or
YUASA
0.55A x 10 hours
1.280 at 200C (680F).