Panasonic WH-ADC1216H6E5C Installationsanleitung Seite 17

 
Signal inputs
L N =AC230V, Heat, Cool=Thermostat heat, Cool terminal
Optional Thermostat
It does not function when using the Optional PCB
Dry contact Open=not operate, Short=operate (System
External control setup necessary)
Able to turn ON/OFF the operation by external switch
Connected (Please use 2 cores wire for relocation and
Remote controller
extension. Total cable length shall be 50m or less.)
  Outputs
AC230V N=Neutral Open, Close=direction (For circuit
3-way valve
switching when connected to DHW tank)
AC230V N=Neutral Open, Close (Prevent water circuit
2-way valve
pass through during cooling mode)
Extra pump AC230V (Used when Tank Unit pump capacity is insuffi cient)
Boiler contact /
Dry contact (System setup necessary)
Defrost signal
  Thermistor inputs
Zone 1 room PAW-A2W-TSRT
sensor Optional PCB
Outdoor air sensor AW-A2W-TSOD (Total cable length shall be 30m or less)
Connection of Optional PCB (CZ-NS4P)
Optional Optional
Thermostat 2 Thermostat 1
L N Cool Heat L
Pool
Pump
Solar
Pump
Error
signal
Zone 1
Pump
Zone 2
Pump
Zone 2 Zone 1 Buffer
room room Tank
sensor sensor sensor
Signal inputs
Optional Thermostat L N =AC230V, Heat, Cool=Thermostat heat, Cool terminal
Dry contact Vcc-Bit1, Vcc-Bit2 open/short (System
SG signal setup necessary)
Switching SW (Please connect to the 2 contacts controller)
Dry contact Open=Heat, Short=Cool (System setup
Heat/Cool SW
necessary)
Dry contact Open=Comp.OFF, Short=Comp.ON
External comp.SW
(System setup necessary)
DC 0~10V (System setup necessary)
Demand signal
Please connect to the DC 0~10V controller.
 
Outputs
AC230V N=Neutral Open, Close=mixture direction
Mixing valve
Operating time: 30s~120s
Pool pump AC230V
Solar pump AC230V
Zone pump AC230V
  Thermistor inputs
Zone room sensor PAW-A2W-TSRT
Buffer tank sensor PAW-A2W-TSBU
Pool water sensor PAW-A2W-TSHC
Zone water sensor PAW-A2W-TSHC
Solar sensor PAW-A2W-TSSO
Recommended External Device Specifi cation
•
This section explains about the external devices (optional)
recommended by Panasonic. Please always ensure to use the
correct external device during system installation.
It does not work when using the
Mixing Mixing
valve 1 valve 2
N Cool Heat N O C N O C
Pool Zone 2 Zone 1 Demand Solar
sensor
water water water signal
sensor sensor sensor
•
For optional sensor.
1. Buffer tank sensor: PAW-A2W-TSBU
Use for measurement of the buffer tank temperature.
Insert the sensor into the sensor pocket and paste it on the
buffer tank surface.
2. Zone water sensor: PAW-A2W- TSHC
Use to detect the water temperature of the control zone.
Mount it on the water piping by using the stainless steel metal
strap and contact paste (both are included).
Dimensions (mm)
35
3. Outdoor sensor: PAW-A2W-TSOD
If the installation location of the outdoor unit is exposed to direct
sunlight, the outdoor air temperature sensor will be unable to
measure the actual outdoor ambient temperature correctly.
In this case, optional outdoor temperature sensor can be fi xed
at a suitable location to more accurately measure ambient
temperature.
Dimensions (mm)
46
Ext.
4. Room sensor: PAW-A2W- TSRT
comp.
SW
Install the room temperature sensor to the room which requires
Heat/
room temperature control.
Cool
SW
Vcc
SG
Bit1
signal
Bit2
5. Solar sensor: PAW-A2W-TSSO
Use for measurement of the solar panel temperature.
Insert the sensor into the sensor pocket and paste it on the solar
panel surface.
6. Please refer to the table below for sensor characteristic of the
sensors mentioned above.
Temperature
(°C)
30
25
20
15
10
5
0
-5
-10
-15
-20
-25
-30
-35
-40
Dimensions (mm)
blue
black
brown
93
93
Dimensions (mm)
30 86
86
Dimensions (mm)
blue
black
brown
Resistance Temperature
(kΩ) (°C)
5.326 150
6.523 140
8.044 130
9.980 120
12.443 110
15.604 100
19.70 90
25.05 80
32.10 70
41.45 65
53.92 60
70.53 55
93.05 50
124.24 45
167.82 40
35
Ø6
40
70
70
60
Ø6
40
Resistance
(kΩ)
0.147
0.186
0.236
0.302
0.390
0.511
0.686
0.932
1.279
1.504
1.777
2.106
2.508
3.003
3.615
4.375
17