Block 3 Bedienmodul Premium - Cloos QINEO CHAMP Pro Betriebsanleitung

Block 3 Bedienmodul PREMIUM

Inhalt
1. Bedienelemente....................................................................................... 43
2. Hauptmenü .............................................................................................. 44
3. MAIN - Synergie ....................................................................................... 45
4. MAIN - Betriebsart .................................................................................. 45
4.1 2-Takt ............................................................................................................................45
4.2 4-Takt ............................................................................................................................46
4.3 Super-4-Takt ..............................................................................................................47
4.4 Punkten ......................................................................................................................47
4.5 Extern...........................................................................................................................47
5. MAIN - Verfahren ..................................................................................... 48
5.1 Elektrode ....................................................................................................................48
5.2 WIG ...............................................................................................................................48
5.3 SpeedPulse ................................................................................................................48
5.4 Pulse .............................................................................................................................48
5.5 MSG normal ..............................................................................................................48
5.6 Syn off ..........................................................................................................................49
5.7 Verfahren mit dem Zusatz CW (Cold Weld) ................................................49
5.7.1 S-Pulse-CW ............................................................................................................49
5.7.2 Normal-CW ...........................................................................................................50
5.8 Rapid Weld .................................................................................................................50
6. MAIN - Funktion ...................................................................................... 51
6.1 DuoPulse ....................................................................................................................51
6.2 CleanStart ..................................................................................................................51
6.3 Ausblasen ..................................................................................................................51
6.4 Draht vor ....................................................................................................................52
6.5 Draht zurück .............................................................................................................52
6.6 Gas von Hand ...........................................................................................................52
6.7 Start von Hand ........................................................................................................52
7. MAIN - Progr.(Programmieren) ............................................................. 53
7.1 Parameter in den Betriebsarten 2-Takt und 4-Takt .................................55
7.2 Parameter in der Betriebsart Super-4-Takt .................................................55
7.3 Parameter in der Betriebsart Punkten / Intervall ....................................57
7.4 Stellbereiche .............................................................................................................58
7.4.1 Voraussetzung zur Nutzung der Stellbereiche .....................................59
7.4.2 Deaktivieren der Stellbereiche .....................................................................60
7.5 MAIN - Programmieren - Tandem ...................................................................61
7.6 MAIN - Programmieren - Impulssync. ..........................................................61
7.7 "Expert Mode" (Einzelparameterbetrieb) ....................................................61
7.7.1 Hauptparameter im "Expert Mode" ..........................................................62
7.7.2 Schweißparameter im "Expert Mode" ......................................................62
7.7.3 "DuoPulse-Parameter" im "Expert Mode" ...............................................63
7.8 Main - Programmieren - Aktiver QWD (ab x.11.50) ................................64
7.9 Main - Programmieren - Schweißkreis (ab x.11.60) ...............................64
8. MAIN - Messwerte ................................................................................... 64
8.1 Betriebsdaten ...........................................................................................................65
8.1.1 Datensatzumschaltung 1/2 ..........................................................................66
8.1.2 Setup Nahtzähler ...............................................................................................66
8.1.3 Verbrauchskosten ..............................................................................................66
9. MAIN - Anzeige ........................................................................................ 67
10. MAIN (2) - Konfig (Konfiguration) ........................................................ 68
10.1 Konfig - Allgemein .................................................................................................68
10.1.1 Displayhelligkeit .................................................................................................68
10.1.2 MHW x10 Master ...............................................................................................69
10.1.3 Steuerung Kühlmittelpumpe und Lüfter ................................................69
10.2 Konfig - Allgemein (2) ...........................................................................................70
41