Preparation; Content Of Delivery / Necessary Accessories - Reely 4WD GP STREETHUNTER 4.1 Bedienungsanleitung

4 P
4.1
S
COPE OF DELIVERY
S
COPE OF DELIVERY
One Chassis
-
- 4,1 ccm two stroke glow engine
with 1,84 kW (2,5 HP), with
manifold, resonance tube, air filter and pull starter,
already mounted
- Steering servo, Throttle/brake servo and receiver,
already mounted
- fuel hoses, already laid.
- Four wheels with plastic disk rims and
already mounted multi spike tires with linings
- car body, imprinted
- Splints to fasten car body
- A plastic tube as guidance for the wire aerial
- Spring pretensionner set
- one two-channel remote control
(pistol grip transmitter)
- This operating manual
S P
PARE ARTS
The spare part list can be found on our Website www.conrad.com in the Download domain specific to the
corresponding product. Alternatively, you can order the spare parts by phone; the contact details are at the
beginning of this operating manual in chapter "Introduction".
A
CCESSORY RECOMMENDATION
Which type of fuel is the right one?
The selection of the fuel has an impact on the performance characteristic of the engine.
However, as a matter of principle:
- In the running-in phase, a special RC car fuel with approximately 16% nitromethane should be used.
- After the run-in of the engine (after a mere operating time of approximately 45 minutes), you can change to a fuel
with approximately 20% nitromethane.
- For maximum output, we recommend the max. percentage of 25% nitromethane
Use fuel for RC cars only!
The percentage of oil contained in fuel for RC plane engines is too small (too little lubrication), which causes the
engine to overheat, thus leading to serious damages.
The same is valid for vehicle gasoline.
Why is a tank bottle needed?
RC model car fuel is available in big bulks (canisters) only. Filling the tank by using a smaller, special tank bottle with a small,
curved pouring tube is significantly simpler. You also prevent spilling fuel (expensive and poisonous).
Are more glow plugs necessary?
Glow plugs wear, especially in the running-in phase. Therefore, we recommend having some glow plugs ready in case of
need for a replacement. There are glow plugs with different calorific values; the selection of the glow plug has a big impact
on driving performance. For the running-in phase, you should use a "hot" glow plug for high performance engines. After the
running-in phase, you can use a glow plug with a middle or a "cold" calorific value.
Use glow plugs for RC cars only! A wrong glow plug, such as e.g. for 4 stroke plane engines, lets the engine
run incorrectly and complicates the tuning.
Replacing the glow plug
To that effect, you need an extra long plug spanner (spider wrench SW 8, 9, 10 and 12), which can be used also to unscrew
the outer hexagonal screws.
Preheating the glow plug
A plug connector (long) with rechargeable battery as a unit is inserted on the glow plug and heats the latter, so that the air-
fuel mix sparks off and the engine starts. When the engine runs smoothly, the plug connector can be removed.
44
REPARATION
,
NECESSARY ACCESSORIES
R
EQUIRED ACCESSORIES
N
OT INCLUDED IN THE DELIVERY
- 12 accumulators (AA) for the transmitter and the receiver
- Glow plug and
- plug spanner
- Plug connector with rechargeable battery as a unit
and
- battery charger
- Tank bottle
Also available as a complete set
Nitrobox II Combuster no. 23 07 99
incl. transport box
- Charger (220V) for the rechargeable batteries or
quick charger to connect to a 12V car battery
- Model fuel methanol/oil based,
minimum share 16% - 25% nitromethane
Operating Instructions 4WD Chassis Hunter / Streethunter 4.1 Item No. 23 47 46 / 23 47 64
: