Gastroback DESIGN ESPRESSO ADVANCED BARISTA Bedienungsanleitung Seite 25

Problem Possible Reasons
Water or splashes given
off by the steam wand
ran out.
The water system is lea-
king.
The drip tray is overfilled, The filling indicator is
but the filling indicator not inserted correctly or
does not come up. missing.
The cup tray is in wrong
orientation. The filling indi-
cator is blocked.
The cup tray wobbles on The cup tray is in wrong
the drip tray or is inclined. orientation.
The filling indicator is not
inserted correctly.
The filter basket cannot For operation, the filter
be removed from the por- basket is engaged within
tafilter. the portafilter via a bulge
at the side wall.
All button are illuminated The selection dial is not
but the extraction function turned to standby cor-
does not work or not work rectly.
correctly.
The water system is over-
heated.
You are using an unsuited
type of water.
EN
122
The Easy Solution
Even when the selection dial is in the central stand-
by position (off), water and steam may escape. Thus,
always turn the steam wand to the drip tray or into a
vessel, when the steam wand is not in use. Wipe spilled
water immediately.
Immediately switch off and unplug the appliance. Get in
contact with your vendor for examination and repair.
Put the red float of the filling indicator onto the post
within the drip tray. Ensure that it can move freely up
and down.
Turn the cup tray by 180°. The large openings must lie
at the rear left side of the appliance. The cup tray must
lie stably and may not wobble. If required, turn the filling
indicator by 90°.
Turn the cup tray by 180°. The large openings must lie
at the rear left side of the appliance.
Turn the filling indicator by 90° and try again.
If you find it difficulty to get the filter basket out, use
a medium screw driver or the handle of a teaspoon for
carefully levering out the filter basket (see: 'Operation /
Inserting the Required Filter Basket').
Turn the selection dial at the left side of the group head
to the vertical standby position. Then try again.
Directly after using the steam function, the water system
is still on steam temperature. Simply wait, until the water
system reaches extraction temperature again. The extrac-
tion starts automatically.
Only use clear, cold tap water or low-mineral, non-carbo-
nated table water. Remove and empty the water tank.
Then refill the water tank and flush the water system
(see: 'Before First Use / Flushing the Water System').
Problem Possible Reasons
Not enough water in the
water tank or the water
tank is not installed cor-
rectly.
The portafilter loosens at The portafilter is not
the group head during an inserted correctly at the
extraction. group head.
There is coffee powder on
the rim of the filter basket
or on the sealing ring of
the group head
AND / OR
moisture on the rim of the
filter basket.
Water or espresso run The filter basket and/or
out at the rim of the por- portafilter are not inserted
tafilter. correctly at the group
head.
There is coffee powder
at the filter basket rim or
coffee powder is sticking
to the sealing ring of the
group head.
The filter basket is
clogged.
The Easy Solution
Fill the water tank at least up the the MIN filling line and
ensure to install the water tank correctly at the rear of
the appliance. When closed correctly, the water tank lid
may not protrude the top of the appliance.
Ensure that the portafilter is rotated to the stop and it is
securely locked in place.
Clean and dry the rim of the filter basket after filling in
coffee powder to ensure a proper seal in group head.
Check the group head for residues of coffee powder (see:
'Care and Cleaning / Cleaning the Group Head').
Ensure that there is no gap between the rim of the filter
basket and the rim of the portafilter.
Ensure that the portafilter is rotated to the right as far as
possible. Ensure that the portafilter is level and securely
locked in place.
After filling, wipe excess coffee powder off the rim of the
filter basket to ensure a proper seal in the group head
(see: 'Operation / Tamping the Coffee Powder').
Clean the shower screen and sealing ring within the
group head (see: 'Care and Cleaning / Cleaning the
Group Head').
Immediately cancel the extraction cycle (press the flas-
hing button) and wait approx. 10 seconds. Thereafter,
carefully remove the portafilter from the group head.
Clean the filter basket. If required, use the cleaning tool
for opening the pores of the filter mesh (see: 'Care and
Cleaning').
When the problem persist, replace the filter basket.
123
EN