Sanyo DC-007C Handbuch Seite 20

MANUAL RECORDING
Previously recorded contents of the MD remain and the selected source
is recorded on the blank portion of the MD.
Note:
Do not select "MD" function. If "MD" is selected, the deck may be set to the
overwriting mode.
1. Load the MD.
2. CD to MD recording
Select "CD" function and play a CD.
Tape to MD recording
Select "TAPE" function and play a cassette.
Tuner to MD recording
Tune in the radio.
Video/DVD to MD recording
Select "VIDEO:DVD" function and play a video cassette or DVD.
3. Press the REC button. The PLAY indicator blinks and the MD deck is
set to the recording pause mode. "New" and "0m 00s" blink alternately.
- If CD recording is selected, "DIGITAL" appears.
4. Press the INPUT button to select the digital or analog input mode if
required.
DIGITAL: Digital input mode, "DIGITAL" appears.
ANALOG: Analog input mode, "ANALOG" appears.
- If "No Digital" blinks, select "ANALOG".
5. While pressing the SHIFT button, press the REC MODE button on the
remote control to select the stereo or monaural recording mode.
STEREO REC: Stereo recording
The sound is recorded in high quality mode. "STEREO"
appears.
MONO REC: Monaural recording
Twice the normal recording time is available. "MONO" appears.
6. Press the PLAY or PAUSE button. Recording starts.
TRACK
TOC
1
- If the REC button is pressed during recording, the track number
is added automatically and recording continues.
7. Press the STOP button to stop recording. (CD play or tape playback
continues.)
CD to MD/Tape to MD synchronous recording
1. Load the MD.
2. Load the CD and select "CD" function, or load the cassette and select
"TAPE" function.
- For CD programmed recording, programme the material in
advance.
3. Press the REC button. The MD deck is set to the recording pause
mode.
4. Press the PLAY button (CD changer), or press the FWD or REV PLAY
button (Tape deck). Recording starts.
- If CD play pauses, recording also pauses and CD play resumes,
recording also resumes. At this time, the track number is added
automatically.
5. Press the STOP button (CD changer or Tape deck) to stop recording.
- When the STOP button (MD deck) is pressed, CD play or tape
playback continues.
Temporarily stop recording
Press the PAUSE button. The PLAY indicator blinks. To resume recording,
press the PLAY or PAUSE button. At this time, the track number is added
automatically.
- During recording pause mode, CD play or tape playback continues.
19
ANALOG
0m 01s
MONO
L
- 40 - 20 - 12 - 8 - 4
REC 0 dB
R
CD to Tape/CD to MD parallel recording
1. Load the cassette and MD.
2. Load the CD and select "CD" function.
3. Press the REC PAUSE button (Tape deck). The tape deck is set to the
recording pause mode.
Press the REC button (MD deck). The MD deck is set to the recording
pause mode.
4. Press the PLAY button (CD changer). CD to tape and MD parallel
recording starts.
5. Press the STOP button (CD changer) to stop recording.
Marking the track number automatically
Track automatic marker
If there is a quiet passage in the music lasting more than 2 seconds, when
recording from a tape or VIDEO, a new track number is made automatically
(Fig. 20).
While pressing the SHIFT button, press the AUTO MARKER button on the
remote control to display "Tr.MARK" in the stop or recording pause mode.
Time automatic marker
A new track number is assigned automatically at the set intervals (1, 2, 3,
. . . 97, 98 and 99 minutes).
1. While pressing the SHIFT button, press the AUTO MARKER button
to display "Ti.MARK" in the stop or recording pause mode.
"Mark 05min" appears and "Ti.MARK" blinks.
2. Turn the MULTI JOG control to select the desired time.
The e / c or d / f button on the remote control can also
-
be used.
3. Press the MULTI JOG control or ENTER button. "Ti.MARK" remains
lit.
To cancel automatic marker
While pressing the SHIFT button, press the AUTO MARKER button until
"Tr.MARKER" or "Ti.MARKER" disappears.
RECORD ON A PRE-RECORDED MD
You can record from the beginning of any pre-recorded track on an MD
(Overwriting). If you do so, previous records (track and track name) will be
erased (Fig. 21).
1. Load the MD and select "MD" function.
2. Turn the MULTI JOG control to select the track to be started a new
recording.
3. Press the REC button. The PLAY indicator blinks and the MD deck is
set to the recording pause mode. "Over Rec" and "0m 00s" blink
alternately.
4. Select the desired function to be recorded.
5. Tuner or Video/DVD function: Press the PLAY or PAUSE button (MD
deck).
CD function: Press the PLAY button (CD changer).
Tape function: Press the FWD or REV PLAY button (Tape deck).
"TRACK" blinks and recording starts.
6. Tuner or Video/DVD function: Press the STOP button (MD deck).
CD function: Press the STOP button (CD changer).
Tape function: Press the STOP button (Tape deck).
Recording stops.