Manual Recording - Sanyo DC-007C Handbuch

Seite von 148

/ 148
Inhalt
Inhaltsverzeichnis
Lesezeichen

Inhaltsverzeichnis

Verfügbare Sprachen

LISTENING TO VIDEO SOURCES/DVD

[Tuner/Amplifier]

1. Press the INPUT button to select "VIDEO:DVD".

2. Follow the instructions supplied with the video equipment/DVD player.

BEFORE TAPE RECORDING [Tape deck]

1. Press the cassette holder (q EJECT portion) to open it and load the

cassette for recording.

2. Set the s B NR button to ON or OFF as desired.

Dolby B NR (ON) ......... " s B" appears

Dolby B NR (OFF) ....... " s B" disappears

3. Press the REV MODE button to select the reverse mode.

V :

For recording one side only.

W :

For recording both sides in succession.

If recording has been started from the reverse side, only the

reverse side will be recorded.

If a tape with one of its tabs already broken out is used for

recording, the tape will not be reversed automatically, and it will

stop.

If the reverse mode has been set to "X", "W" appears

automatically when the recording mode is established.

Automatic record muting

Undesirable parts of a programme can be omitted while recording.

Press the REC MUTE button once while recording. The REC PAUSE

indicator blinks and a 5-second unrecorded blank space is created, then

the deck enters the recording pause mode. The REC PAUSE indicator

lights and the REV or FWD PLAY indicator blinks.

To add another 5-second blank space, press the REC MUTE button

again.

To resume recording, press the TAPE a or b button (to match the

blinking PLAY indicator).

Note:

The record muting function does not operate during CD/MD computer

recording.

Safeguards against accidental erasure

Accidental erasure can be prevented by breaking out the tabs on the end

of the cassette tape (where the tape is not exposed) using a screwdriver

or similar implement (Fig. 16).

If a tab is broken out in error and you wish to re-record the tape, simply

block the tab hole using adhesive tape and the tape can be used for

recording again.

(Remote control only)

TAPE RECORDING [Tape deck]

CD TO TAPE COMPUTER RECORDING

With computer recording, you can record a CD onto a cassette by pressing

just one button.

1. Load the CD(s) to be recorded.

2. Load the blank cassette for recording.

3. Press the REV MODE button to select "W" mode.

4. Select "CD" function.

For programmed recording from up to 3 CDs, programme the

material in advance (as described under "PROGRAMMED PLAY").

5. Press the DISC SELECT button (1, 2 or 3) to select the disc to be

recorded first, then press the STOP button (CD changer).

For programmed recording, this step is unnecessary.

6. Make sure that the CD changer and tape deck are both in the stop

mode.

7. Press the COMPU REC button. Once the button is pressed, all

operations take place automatically. The COMPU REC indicator

lights and "CD –> TP" appears on the display.

The system automatically performs the following functions:

Tape deck:

The tape rewinds to the beginning.

Recording starts in the forward direction.

CD changer:

The changer searches for the first track to be recorded, then

enters the pause mode.

CD play starts.

The FWD PLAY, REC PAUSE, COMPU REC (Tape deck), PLAY (CD

changer) indicators light and the selected disc number indicator (CD

changer) blinks as recording begins. The following display appears.

COMPU.REC

When the end of the tape (side B) is reached, the CD changer and

deck stop automatically.

If the last track on the CD plays completely before the end of the

tape, CD play stops automatically. Deck also stops.

Note:

Recording starts automatically after 8 seconds, so the recording will

not be interrupted by the leader tape at the beginning of tape.

A 5-second blank space is automatically recorded at the end of each

track.

The recording cannot be paused.

To stop recording at any time, press the STOP button (CD changer or

Tape deck).