English; Connections (Fig. 3) - Sanyo DC-007C Handbuch

ENGLISH

PRECAUTIONS
- The apparatus shall not be exposed to dripping or splashing.
- Do not use where there are extremes of temperature (below 5°C or
exceeding 35°C) or where direct sunlight may strike it.
- Because of the CD changer/MD deck's extremely low noise and wide
dynamic range, there might be a tendency to set the volume on the
amplifier unnecessarily high. Doing so may produce an excessively
large output from the amplifier which could damage your speakers.
- Sudden changes in the ambient temperature may cause condensation
to form on the optical lens inside the unit. If this happens, take out the
disc (CD or MD), leave the unit for about 1 hour, and then proceed to
operate.
- When carrying the unit, be sure to remove the discs (CD and MD)
which may be inside and turn the power off. Wait at least 10
seconds, then unplug the mains lead from the AC outlet.
Otherwise, may damage the disc and/or the unit.
- The system's speakers use powerful magnets. Do not place timepieces,
credit cards, cassette tapes or video tapes, etc. near the speakers.
- Do not install this equipment in a confined space, such as a book case
or built in cabinet.
Recording copyright material without permission of the copyright owners
is usually an infringement. If you wish to re-record copyright material,
permission from the copyright owner is necessary. SANYO does not
approve of, and cannot be held responsible for, any unlawful use of this
machine.
ARRANGEMENT (Fig. 2)

CONNECTIONS (Fig. 3)

Note:
- Do not connect the mains lead to an AC outlet until all connections
have been made.
- The system is not completely disconnected from the mains when the
z/ON button is set to the z position.
- To prevent a noise interference from the mains, the core clamp is
attached to the mains lead. Do not remove it.
Notes on the flat connection lead
When using only the system DC-007C (CD changer and Tuner/
Amplifier)
The flat connection lead is provided as shown in Fig. 4a. Connect the CD
changer and Tuner/Amplifier with this lead as shown in Fig. 4.
- Do not remove the fixer and protective tape.
When using the system DC-007C (CD changer and Tuner/Amplifier)
and optional Tape deck and/or MD deck
Remove the fixer and protective tape before connecting.
- Do not remove the tape on the plug that is not used.
To connect
Push the middle of the plug and insert it until it clicks as shown in Fig. 3a.
- If you have difficulty inserting the plug, turn it over and reinsert it.
To disconnect
While pressing both latches, remove the plug as shown in Fig. 3b.
9
Speakers (Fig. 5)
When connecting the speakers, make sure that (+) and (–) polarities are
matched properly. Otherwise, the sound may appear to be lacking in the
bass range and in stability.
Connect the speaker wire with the stripe to the red terminal (+) and the
other wire to the black terminal (–).
Note:
If desired, the speaker grilles can be removed.
Aerials (Fig. 5)
In areas close to a transmitter the simple indoor aerial is sufficient to
receive broadcasts. Extend the aerial wire as straight as possible and,
while listening to the sound from the system, secure it in a position which
yields minimal distortion and noise.
In fringe areas or where reception is distorted or noisy, an external aerial
(not supplied) should be connected instead of the simple indoor aerial.
Consult your dealer.
AM loop aerial
Assemble the loop aerial as shown in Fig. 6a. Unwind the aerial wires,
then connect them to the AM LOOP terminals. Place the loop aerial in a
position which yields the best AM reception, or attach it to a wall or other
surface as shown in Fig. 6b.
Note:
To minimize noise, the speaker, mains and any other leads should not
come close to the indoor or external aerial lead and AM loop aerial. Do not
place the aerial leads close to the system.
Video equipment/DVD player
Connect audio leads (not supplied) from the audio output sockets of a
video equipment/DVD player to the VIDEO (AUDIO) sockets.
Subwoofer
Connect an amplified subwoofer (not supplied) to the SUB WOOFER OUT
socket.
Digital equipment
The OPTICAL DIGITAL OUT socket (MD deck) reproduces MD's digital
sound to your digital equipment. Before connecting, remove the cap on
this socket. The socket can be connected to the digital equipment which
has an optical input socket.
Headphones
Connect stereo headphones (not supplied) to the PHONES socket for
monitoring or for private listening. The speakers are automatically
disconnected when headphones are connected.