Sanyo DC-007C Handbuch Seite 16

To search a preset station by PTY codes
A particular programme type broadcast can be located by specifying the
PTY codes.
1. Press the RDS MODE button to select "PTY" while listening to an FM
station.
2. Turn the UP/DOWN control within 2 seconds to select the desired PTY
code. The PTY code changes as shown below:
NEWS: News
AFFAIRS: Current affairs
INFO: Information
SPORT: Sport
EDUCATE: Education
DRAMA: Drama
CULTURE: Culture
SCIENCE: Science
VARIED: Varied
POP M: Pop music
ROCK M: Rock music
M.O.R. M: Middle of the road music (easy-listening)
LIGHT M: Light classics
CLASSICS: Serious classics
OTHER M: Other music
WEATHER: Weather
FINANCE: Finance
CHILDREN: Children's programmes
SOCIAL: Social affairs
RELIGION: Religion
PHONE IN: Phone in
TRAVEL: Travel
HOBBIES: Hobbies
JAZZ: Jazz music
COUNTRY: Country music
NATION M: National music
OLDIES: Oldies music
FOLK M: Folk music
DOCUMENT: Documentary
TEST: Alarm Test
ALARM: Alarm
(or in the reverse sequence)
3. Press the PTY CHECK button within 10 seconds. "PTY CHK" blinks
on the display.
The unit searches 24 preset stations and stops when it finds a
broadcast of the PTY code you have selected, then tunes into that
station.
- To continue searching after the first stop, press the PTY CHECK
button again while the display blinks.
- If no broadcast is found, "NO PTY" appears, then the original
station is heard.
To cancel searching, press the RDS MODE button.
15
LISTENING TO TAPES [Tape deck]
If a cassette is loaded, you can turn the system on and begin play
immediately by pressing the TAPE a or TAPE b button (Remote
control only).
1. Press the INPUT button (Tuner/Amplifier) to select "TAPE".
2. Press the cassette holder (q EJECT portion) to open it.
3. Load the cassette (Fig. 14).
After loading the cassette, push the cassette holder (q EJECT
portion) back into position.
4. Set the s B NR button according to whether the tape has been
recorded with the Dolby B NR system or not.
With Dolby B NR ....................... " s B" appears
Without Dolby B NR .................. " s B" disappears
5. Select the reverse mode with the REV MODE button as desired.
6. Press the FWD PLAY or REV PLAY button to begin playback. The
selected indicator lights.
FWD PLAY: Forward play
REV PLAY: Reverse play
sB
7. Press the STOP button to stop playback at any time.
When the end of the tape has been reached, automatic stop or reverse
will be activated.
Types of usable tapes
The type of tape used is automatically identified by the system since deck
employs an auto tape selection system. The following types of tape can
be used with this system.
Normal
CrO
2
Metal (Only for playback)
Note:
- CrO /Metal tapes without sensing holes cannot be used since they
2
cannot be identified by the auto tape selector.
- Endless tapes cannot be used.
- Do not use C-100 (or longer) tapes. They may jam in the mechanism.
Auto reverse
Press the REV MODE button to select the reverse mode as desired.
V :
For listening to one side of the tape only.
W :
For listening to both sides of the tape in succession.
- If playback has been started from the reverse side, only the
reverse side will be played back.
X :
For listening repeatedly to both sides of the tape.
Tape counter
The counter appears on the display and helps you to quickly locate the
recorded selection for playback.
To reset the tape counter to "000", press the STOP button in the stop
mode.
Fast forward and rewind
Press the c or d button. The FWD PLAY or REV PLAY indicator
blinks. When the desired location has been reached, press the STOP
button.
Dolby NR system
Dolby Noise Reduction circuitry provides superior recording and playback
results by suppressing tape hiss by up to 10 dB.
Dolby noise reduction manufactured under license from Dolby Laboratories
Licensing Corporation.
"DOLBY" and the double-D symbol s are trademarks of Dolby Laboratories
Licensing Corporation.