Herunterladen Inhalt Inhalt Diese Seite drucken

Sanyo DC-007C Handbuch Seite 13

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 27
WHAT TO DO IF ...
If the operation of the system or display is not normal,
1. Disconnect the mains lead.
2. Press the RESET button (bottom of the Tuner/Amplifier) for at least 30
seconds (Fig. 9).
3. Connect the mains lead.
4. Resume the operation.
CD/MD PREPARATIONS
CD (Compact Disc)
Use CDs bearing the symbol shown in Fig. 10a. In addition to conventional
12 cm CDs, the CD changer can be used to play 8 cm CDs without an
adapter.
Notes on handling CDs
-
Do not expose the CD to direct sunlight, high humidity or high
temperatures for extended periods of time.
-
CDs should be returned to their cases after use.
-
Do not apply paper or write anything on the disc surface.
-
Handle the CD by its edge. Do not touch the playing surface (glossy
side).
-
Fingerprints and dust should be carefully wiped off the playing surface
of the disc with a soft cloth.
Wipe in a straight motion from the centre to the outside of the disc.
-
Never use chemicals such as record cleaning sprays, antistatic
sprays or fluids, benzene or thinner to clean CD.
MD (Mini Disc)
Use MDs bearing the symbol shown in Fig. 10b.
Notes on handling MDs
The disc is enclosed in the cartridge to protect it from dust and fingerprints,
but the cartridge can be damaged if it is not stored carefully. Pay attention
to the information below.
-
Do not open the shutter forcibly or touch the disc inside (Fig. 11).
-
Forcing the shutter open can damage the MD and make it unusable.
-
MDs should be returned to their cases after use.
-
Do not expose MDs to direct sunlight, high humidity or high temperatures
for extended periods. Do not leave them in dusty or sandy locations.
-
Carefully wipe dust from the cartridge with a soft cloth. Be careful not
to damage the shutter.
-
Never use chemicals such as antistatic sprays or fluids, benzene or
thinner to clean MD.
Types of MDs
Playback (read only) MD (Fig. 12a)
There is a shutter on one side (back side) of the disc.
Recordable MD (Fig. 12b)
There are two types of recordable MDs (60-minute and 74-minute).
There is a shutter which covers both sides of the disc.
When placing a label on the MD
Please follow the instructions below.
-
Make sure to place the label in the correct location (within the
recessed labeling area).
-
Do not laminate the labels. Remove the old label before placing a new
label on the disc.
-
When the label is not placed securely, replace it with a new one.
US and foreign patents licensed from Dolby Laboratories Licensing
Corporation.
CD PLAY [CD changer]
Note:
-
Do not touch the disc tray while it is moving.
-
Never place anything except a CD on the disc tray. Foreign objects
can damage the unit.
-
Do not apply excessive force to the disc tray.
-
Discs must be placed on the disc tray one at a time.
If a CD is loaded, you can turn the system on and begin play
immediately by pressing the CD a button (Remote control only).
1. Press the INPUT button (Tuner/Amplifier) to select "CD" function.
2. Press one of the DISC SELECT buttons (1, 2 or 3), then press the q
OPEN/CLOSE button. The selected disc tray slides out and "OPEN"
appears.
-
If the changer mechanism has detected "NO DISC" for the DISC
SELECT button pressed, the tray slides out automatically.
3. Place the CD with the label facing up on the disc tray (Fig. 13).
4. Press the q OPEN/CLOSE button again to close the disc tray.
Note:
To open or close the disc tray, be sure to use the q OPEN/CLOSE
-
button. Do not touch the disc tray by hand.
-
If the CD is loaded with the label facing downward, or if a badly
scratched CD is loaded, "NO DISC" appears. If this occurs, load
the CD correctly or replace the damaged CD.
5. Repeat steps 2 - 4 to load another CD.
6. Press one of the DISC SELECT buttons (1, 2 or 3). The selected disc
number indicator (DISC 1, 2 or 3) blinks and PLAY indicator lights.
Play starts from the first track of the selected CD.
1
TR
2
3
The track number and elapsed playing time for the current track are
displayed.
-
If the desired CD has been selected, the PLAY button can also be
used to start play.
7. Press the STOP button to end CD play.
When the last track of the last CD has been played, the CD changer
stops automatically.
When the q OPEN/CLOSE button is pressed during play, play will
-
stop and the disc tray will slide out.
Ejecting or replacing CDs
1. While in the CD play or stop mode, press one of the DISC SELECT
buttons to be ejected, then press the q OPEN/CLOSE button.
-
While the changer is playing one CD, you can eject or replace
another CD without stopping play.
2. Remove or replace the CD.
3. Press the q OPEN/CLOSE button.
To start play from the desired track
1. Press the desired DISC SELECT button, then press the STOP button.
2. Select the desired track by using the e / c or d / f button,
then press the PLAY button.
Using the remote control
1. Select the desired CD by pressing the DISC SELECT button, then
press the n button.
2. Press number button(s). (Example: To select track 3, press 3. To
select track 12, press +10, then press 2 within 4 seconds.)
Temporarily stopping play
Press the PAUSE button. The PLAY indicator blinks. To resume play,
press the PLAY button.
NOR
12

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis