Adjusting The Clock - Sanyo DC-007C Handbuch

Inserting batteries
Install two "R6/AA" batteries (not supplied) as shown in Fig 7.
Note:
Always remove batteries if the remote control is not to be used for a month
or more. Batteries left in the unit may leak and cause damage.
Remote control range (Fig. 8)
The buttons on the remote control perform similar functions to similarly
buttons on the front panel. See "REMOTE CONTROL OPERATION" for
more details.

ADJUSTING THE CLOCK

[Tuner/Amplifier]
When connecting the mains lead for the first time, the clock display blinks.
For easy operation, adjust the clock at that condition.
Example: To set "6:30",
1. Press the MEMORY button.
The hours display blinks.
2. Turn the UP/DOWN control to set the hours.
3. Press the MEMORY button.
The minutes display blinks.
4. Turn the UP/DOWN control to set the minutes.
5. Press the MEMORY button. The clock starts, then the clock display
disappears.
- The time can be set accurately by pressing the MEMORY button
when a time signal is heard.
- These operations can be done, even if in power on. First, press the
CLOCK/ECO button to display the clock, then follow steps above.
- To display the clock during operation, press the CLOCK/ECO button.
Press it again to return to the original display.
- When the display blinks because of a power failure, reset the time.
Changing the clock to the 12-hour display
1. Turn the power off.
2. If the clock is not displayed, press the CLOCK/ECO button to display
the clock.
3. While pressing the MEMORY button, press the SET/CLEAR button.
Example: 13:00 v PM 1:00
To return the original setting, repeat steps above.
11
(Main unit only)
GENERAL OPERATION [Tuner/Amplifier]
Turning the power on and off
Press the z/ON button (Tuner/Amplifier). All the units turn on. The
displays light and "WELCOME" appears briefly. (After connecting the
mains lead, when you press the z/ON button for the first time, the volume
reset feature automatically sets the initial volume level.)
To turn the power off, press the z/ON button again. All the units turn off.
- When the mains lead is connected to the AC outlet, the unit will
respond to commands from the remote control.
Ecology (low power consumption) standby mode
The unit is set to the ecology standby mode when it is shipped from the
factory. When turning the power off, no display appears on the display. To
cancel this mode, press the CLOCK/ECO button (in the power is off). The
clock appears. Press it again to return to the ecology standby mode.
Direct start function
(Remote control only)
If the following buttons are pressed when the unit is in standby, the unit
turns on automatically and the selected function is set.
CD a, TUNER/BAND, VIDEO, TAPE a, TAPE b, MD a
Selecting the function
Press the INPUT button to select the desired function (input source). Each
time the button is pressed, the display changes as follows:
CD v TAPE v TUNER v MD v VIDEO:DVD v
If the following buttons are pressed (except during recording), the function
is automatically selected.
PLAY, DISC SELECT (CD changer), BAND (Tuner/Amplifier), REV
PLAY, FWD PLAY (Tape deck), PLAY (MD deck)
- When the function selection is changed, CD play, tape playback or MD
play is automatically stopped.
Adjusting the volume
Turn the VOLUME control, (or press the + or – VOLUME button on the
remote control). The volume level appears on the display (VOL 0 ~ VOL
MAX).
Adjusting the left/right speaker balance
1. Press the BALANCE button. The following indication appears on the
display.
2. Turn the VOLUME control while the balance indication appears to
adjust the left/right speaker balance.
Adjusting the tone
Turn the BASS control to adjust the bass sound. The bass level appears
on the display (BASS –6 ~ 0 ~ +6).
Turn the TREBLE control to adjust the treble sound. The treble level
appears (TREBL –6 ~ 0 ~ +6).
To reduce the volume temporarily (muting)
(Remote control only)
Press the MUTE–20dB button. "MUTE" blinks on the display. To restore
the previous volume setting, press the MUTE–20dB button again. "MUTE"
disappears.
Bass boost
(Remote control only)
Press the SUPER BASS button to enhance the bass sound. "BASS"
appears on the display.
- The initial setting of this function is ON.
Adjusting the displays brightness (Both Tuner/
Amplifier and MD deck)
While pressing the MEMORY button, press the CLOCK/ECO button.
DIMMER 1 v DIMMER 2 v DIMMER 0 (initial setting)
To turn off the blue lights on the MD deck, select "DIMMER 2".
(Main unit only)