IFM Electronic Ecomat 100 Original-Programmierhandbuch Seite 273

ifm Programmierhandbuch SmartController (CR2530, CR2532) v03.03
Anhang
Index S-Idx Parameter name
0x1 Short circuit OUT00...OUT07
0x2023 0x0 Output – open circuit
0x1 Open circuit OUT00...OUT07
0x2024 0x0 Output – overload
0x1 Overload OUT00...OUT01
0x2025 0x0 Input analog – overcurrent
0x1 Overcurrent IN00...IN03
0x2030 0x0 Input resistor
0x1 Resistance IN04
0x2 Resistance IN05
0x2040 0x0 System supply voltage VBBS
0x1 VBBS
0x2041 0x0 Output supply voltage
0x1 VBB1
0x2 VBB2
0x2050 Device temperature
0x20F0 Node ID
0x20F1 Node ID
0x20F2 Baud rate
0x20F3 Baud rate
0x20F4 Autostart
0x6000 0x0 Binary input
Largest sub-index supported
Data type Default Details
ro USINT 0 0 = normal
1 = short circuit
ro USINT 1 Largest sub-index supported
ro USINT 0 0 = normal
1 = open circuit
ro USINT 1 Largest sub-index supported
ro USINT 0 0 = normal
1 = overload
ro USINT 1 Largest sub-index supported
ro USINT 0 0 = normal
1 = overcurrent
ro USINT 2 Largest sub-index supported
ro UINT 0 0...30 000
ro UINT 0 0...30 000
ro USINT 1 Largest sub-index supported
ro USINT 0 VBBS voltage [mV]
ro USINT 2 Largest sub-index supported
ro UINT 0 VBB1 voltage [mV]
ro UINT 0 VBB2 voltage [mV]
ro INT 0 temperature [°C]
rw USINT 124 1...125
rw USINT 124 1...125
rw USINT – baud rate
[!] value(0x20F2) != value(20F3)
rw USINT – baud rate
[!] value(0x20F2) != value(20F3)
rw UINT 0 nicht benutzt
ro USINT 0x02 Binär-Eingänge
Größter unterstützter Sub-Index = 2
273
Integriertes E/A-Modul: Beschreibung
channels (bit coded)
0b---- ---X = OUT00
0b---- --X- = OUT01
0b---- -X-- = OUT02
0b---- X--- = OUT03
0b---X ---- = OUT04
0b--X- ---- = OUT05
0b-X-- ---- = OUT06
0bX--- ---- = OUT07
channels (bit coded)
0b---- ---X = OUT00
0b---- --X- = OUT01
0b---- -X-- = OUT02
0b---- X--- = OUT03
0b---X ---- = OUT04
0b--X- ---- = OUT05
0b-X-- ---- = OUT06
0bX--- ---- = OUT07
channels (bit coded)
0b---- ---X = OUT00
0b---- --X- = OUT01
channels (bit coded)
0b---- ---X = IN00
0b---- --X- = IN01
0b---- -X-- = IN02
0b---- X--- = IN03
IN04 resistance [Ohms]
IN05 resistance [Ohms]
node ID
[!] value(0x20F0) != value(20F1)
node ID
[!] value(0x20F0) != value(20F1)
2018-05-18