Layout; Before Commissioning - Scheppach Hp1400S Originalbetriebsanleitung

m WARNING!
The product and the packaging material are not
children's toys! Do not let children play with plas-
tic bags, films or small parts! There is a danger of
choking or suffocating!

8. Layout

You will need the following to assemble the plate com-
pactor:
• 16 mm open-ended spanner (not included in the
scope of delivery)
• Phillips screwdriver (not included in the scope of
delivery)
• Enclosed accessories bag
8.1 Fitting the handle (Fig. 3 + 4)
1. Unfold the guide bar with handle (1).
2. Slide the guide bar with handle (1) between the
fixing lugs and secure it with two hexagonal bolts
M10 x 70 (1a), two screws 10 mm (1b) and two stop
nuts (1c).
3. Attach the throttle (2) to the upper handle (1) with
a Philips screw M5 x 35 (2a) and a washer (2b).
You can tension the cable using the Bowden cable
screw on the throttle (2).
8.2 Fitting the transport frame (Fig. 5)
1. Secure the pre-assembled transport frame (12) to
the mounting lugs with two hexagonal bolts M10 x
30 (12a), two washers 10 mm (12b) and two stop
nuts (12c). Tighten the screws only enough to al-
low the joint on the chassis to still move.
2. Now fold up the complete transport frame (12)
in working position and attach it to the transport
frame hooks (17).
Attention: Always fold up and hook in the transport
frame (12) before compacting! Make sure that the joint
of the transport frame is free to move so that it can be
folded up.
8.3 Fitting the rubber pad (Fig. 6)
When using the plate compactor on paving stones, fit the
rubber pad (20) to prevent chipping and scratching of the
stone surface.
Attention! Use the rubber pad only for bedding in con-
crete blocks, concrete slabs and similar.
Remove the rubber pad when compacting gravel, grit
and the like.
1. To mount the rubber pad (20), place the machine
with the plate compactor on the rubber pad.
36 | GB
Align the rubber pad so that the holes match the
screw points on the device.
2. Fasten the rubber pad (20) with the fastening strip
(21) on the front side with two hexagonal bolts M10
x 30 mm (21a) each, two spring washers A10 mm
(21b) and two hexagonal nuts (21c).
3. Tighten all the screws well.
9.

Before commissioning

m Attention!
Always make sure the product is fully assembled
before commissioning!
m WARNING!
Health hazard!
Inhalation of petrol/lubricating oil vapours and exhaust
gases can cause serious damage to health, uncon-
sciousness and in extreme cases death.
- Do not breathe petrol/lubricating oil vapours and
exhaust gases.
- Operate the product outdoors only.
NOTE!
Product damage
Using the product without or with too little engine and
gearbox oil can result in engine damage.
- Fill with petrol and oil before commissioning. The prod-
uct is supplied without engine and gearbox oil.
NOTE!
Environmental damage!
Spilled oil can pollute the environment permanently.
The liquid is highly toxic and can quickly lead to water
pollution.
- Fill/empty oil only on level, paved surfaces.
- Use a filling nozzle or funnel.
- Collect drained oil in a suitable container.
- Wipe up spilled oil carefully immediately and dis-
pose of the cloth according to local regulations.
- Dispose of oil as per local regulations.
NOTE!
Risk of damage!
If incorrectly stored or undrained fuel is used, the car-
burettor may become clogged or engine operation may
be affected.
- Put unused fuel in an airtight vessel and store it in
a dark, cool room.
www.scheppach.com