Explanation Of Symbols And Safety Instructions; Explanation Of Symbols; General Safety Instructions; Information On Individual Control - Bosch Src 100 Rf Installations- Und Bedienungsanleitung

1

Explanation of symbols and safety instructions

1.1

Explanation of symbols

Warnings
In warnings, signal words at the beginning of a warning are used to
indicate the type and seriousness of the ensuing risk if measures for
minimizing danger are not taken.
The following signal words are defined and can be used in this
document:
DANGER
DANGER indicates that severe to life-threatening personal injury will
occur.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could
result in serious personal injury or danger to life.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could
result in minor to moderate personal injury.
NOTICE
ATTENTION indicates that material damage may occur.
Important information
The info symbol indicates important information where there is no risk to
people or property.
1.2

General safety instructions

Notices for the target group
These installation instructions are intended for competent persons who
are skilled in dealing with water installations, ventilation, heating and
electrical systems. All instructions must be observed. Failure to comply
with instructions may result in material damage and personal injury,
including danger to life.
▶ Read these instructions before starting any installation.
▶ Observe the safety instructions and warnings.
▶ Follow national and regional regulations, technical regulations and
guidelines.
▶ Document all work carried out.
Intended use
▶ Use the product only to control heating systems.
Any other use is considered inappropriate. We take no responsibility for
damage caused through incorrect use.
Installation, operation or warnings for the components mentioned below
are not part of these installation and operating instructions. This and
other information can be found in the relevant documentation for the
respective components (products).
SRC 100 RF – 6721856014 (2024/11)
Explanation of symbols and safety instructions
2

Information on individual control

2.1

General description

This commissioning and user manual describes the general functionality
of the individual control feature, in which combination the feature can be
used and how it is activated (set). It has been created for trained
specialists.
Installation, operation or warnings for the components mentioned below
are not part of these installation and operating instructions. This and
other information can be found in the relevant documentation for the
respective components (products).
Appropriate components and settings are required to use the individual
control feature, which are described in more detail below. Use the
feature only in combination with the components listed in the
compatibility list.
The individual control feature is available in the following countries:
Germany, Austria, Switzerland, Luxembourg, Belgium, Netherlands,
Italy, Czech Republic, Poland and Hungary.
▶ Use only individual control in these countries.
2.2

General description of individual control

Individual control is a feature that can be used in combination with
certain wall hung condensing boilers or heat pumps to optimise the
heating system as a whole in terms of Comfort, Efficiency, Planning
and Commissioning.
• Comfort in every room
– Individual room temperature-dependent control and adjustable
time program (weekly profile) in every room. Everything at a
glance from the comfort of your sofa or on the move with the app
Bosch HomeCom Easy.
– The individual controls switch automatically between Heating,
Cooling, Off and Holiday mode. This means that it is no longer
necessary to switch all individual controls manually.
• Efficiency through intelligent networking
– The individual control automatically determines the optimum flow
temperature and thus ensures the most efficient operation of the
heat generator.
• Simple planning and commissioning
– Automatic determination of the flow temperature eliminates the
need for time-consuming determination and setting of the heating
curve.
– Even heat distribution in every room is regulated with the help of
automatic hydraulic balancing. This automatic system eliminates
the need for radiator-specific calculation and manual adjustment
at each radiator.
– Installation and operation is possible without the Internet.
Comparable individual control or smart home systems almost
always require an internet connection for installation and
operation. To use the Bosch HomeCom Easy app, the internet
connection can be set up by the end user later on.
– The demands-based control of cooling operation according to
cooling requirements and humidity ensures the highest possible
condensation protection with the networked individual controls
for underfloor heating system compared to systems with only one
humidity sensor. This eliminates the need to think long and hard
about the best position for the air humidity sensor.
51